Slide Unit Series CXWM/CXWL Provided with shock The slide unit can absorb energy in a wide range, in high-speed, low-load applications to low-speed, high-load applications, without requiring adjustments. Ensures high positional A high level of positional accuracy can be attained because the two parallel piston rods prevent the rods from rotating, and the workpiece mounting surface and the parallelism of the piston rods are made highly precise. The slide unit can be mounted on the housing or on the plate, depending on the application. It can also be bolted from the bottom or from the top. The piping can be fitted to the port in any of the three positions, according bottom side bottom side upper side upper side Series CXWM Built-in shock absorber Series CXWL Built-in shock absorber Note 1) Only E type reed switch is applicable as an auto switch when mounting a housing of a 10. )1 Note 2) The shock absorbers are to be mounted on the both sides for the 25-stroke of Note 3) The shock absorber is to be mounted on one side of the plate for the 25-stroke of

i Take precautions to prevent your fingers or hands from getting caught between the plate and the housing. • Exercise extreme caution when the cylinder is operating, to prevent injury to your fingers or hands. ©Make sure that the cylinder mounting surface is flat (a flatness of 0.05 or less {reference value}). If it is not flat, it could lead to a malfunction. ©Make sure not to scratch or gouge the cylinder mounting Be aware that if the flatness of the housing mounting surface or the mounting surface of the plates on both sides is affected, it could lead ©Be careful not to twist the two piston...

Series CX Prior to Use Comparison on the starting pressure by the moment (Reference data for selection a slide bearing or a ball bushing bearing) CMWM (Slide bearing) CXWL (Ball bushing bearing) Comparison on the starting pressure with the load mounted and the moment added Note) The diagram below does not show the allowable moment. It compares the starting pressure of the slide bearing to that of the ball bushing when the load of the moment is applied to the bearing. 0.35 0.30 0.25 0.20 1.25 1.50 1.75 2.0 0.35 0.30 0.25 0.20 3.5 Moment (Nm) Starting pressure (MPa) Starting pressure (MPa) 5.0...

1 Changing from the non-auto switch specification to the auto switch specification © Changing mounting style of the auto switch specification_ Series CXWÏ ® In the CXW L1 series, to change from the specification without auto switch to the plate mounting style with auto switch or to the housing mounting style with auto switch, refer to tables 1 and 2 before ordering. - Without auto switch/ CXWÎ? Plate mounting style with auto switch Housing mounting _. . (D In the CXW L series, to change from the plate mounting style with an auto switch to the housing mounting style with an auto switch or vice...

Slide Unit/Built-in Shock Absorber Series CXWM With Auto Switch Cylinder with auto switch • Slide bearing Cylinder bore size/Stroke (mm) • Number of auto switches • Auto switch * Refer to the table below for the part numbers for auto switches. Note 1) For the strokes Indicated In the parentheses of the a 10, 016 and a25, shock absorbers are to be J) mounted on both sides of the plate. For the strokes Indicated In the parentheses of the a20 and a32, a shock absorber Is to be mounted on single side of the plate. Note 2) Refer to p.2-67 for the strokes other than those Indicated above. Note 3) For...

Series Slide Unit/Slide Bearing: Built-in Shock Absorber Built-in shock absorber This is a built-in shock absorber style in which the shock absorber is enclosed in the housing. Compared to the CX2 series with shock absorber, this style achieves space savings in the longitudinal direction (except for the 25mm stroke). Dramatically reduced installation labour The machining precision required for positioning during the installation of the cylinder has been reduced through the adoption of a special pin hole machining process, thus decreasing the amount of labour involved in adjustment. Provided with...

CXWM Series Weight (kg) Stroke (mm) Model 25 50 75 100 125 150 175 200 CXWM10 0.28 0.35 0.42 0.49 — — — — CXWM16 0.46 0.59 0.72 0.85 0.98 1.11 1.24 1.37 CXWM20 0.69 0.87 1.03 1.22 1.40 1.58 1.75 1.93 CXWM25 0.95 1.17 1.38 1.60 1.82 2.03 2.31 2.47 CXWM32 2.01 2.38 2.77 3.16 3.56 3.94 4.34 4.72 Additional Weight for End Lock Model (CXWM-R) (kg) Applicable model Additional weight CXWM10 0.08 CXWM16 0.14 CXWM20 0.15 CXWM25 0.20 CXWM32 0.43 Accessory (Option) Straight knock pin Operating direction per pressurized port Operating direction of the housing when the plate part is fixed With end lock (CXWM-R)...

Slide Unit/Slide Bearing: Built-in Shock Absorber Construction: Series CXWM ø10, ø16, ø25 CXWM10 With end lock CXWM16, 25 ø16/With end lock ø25/With end lock Component Parts/With end lock Component Parts No. q w e r t y u i Description Rod cover Housing Piston Piston rod Plate Lock nut Adjusting bolt Set screw (For fixing rods) Material Aluminum bearing alloy Aluminum alloy Aluminum alloy Notes Aluminum alloy Carbon steel Chrome steel Hard anodized Chromated Hard chrome plated Hard anodized Nickel plated Nickel plated Chrome steel Nickel plated Carbon steel piping for machine constructions o...

Series CXWM Component Parts Component Parts Replacement Parts: Seal kits Note 1) The strokes Indicated In the parentheses are of CXWM20, and CXWM32 Includes the strokes Indicated In the parentheses. Replacement Parts: Seal kits * The seal kit Includes a piston seal ©, a rod seal © and a cylinder tube gasket ( List the order numbers In compliance with the respective models. (The piston gasket Is not replaceable.) * The seal kit Includes a body gasket ©, a rod seal ©, a piston seal © and an 0 ring ©. List the order numbers In compliance with the respective models