Group: SMC
Catalog excerpts
Ionizer New RoHS Potential amplitude: 25 V or less Rapid elimination of static electricity: Fastest time: 0.1 seconds Note 1) Dual AC type Note 2) Series IZS42 Potential amplitude is reduced with Dual AC type. Feedback sensor type Series IZS41 Rapid elimination of static electricity by a feedback sensor Standard type Series IZS40 Simple operation: Can be controlled by powering the ionizer ON. Note 1) IZS42, Installation height: 300 mm Note 2) Conditions/With feedback sensor Charged voltage: 1000 V 100 V Discharged object: Charged plate (150 mm x 150 mm, capacitance 20 pF) Installation distance: 200 mm (Tungsten electrode needle with air purge) Series IZS40/41/42 CAT.ES100-97A
Open the catalog to page 1Dual AC type Series IZS42 (Potential amplitude reduction specification) Potential amplitude: 25 V or less 80% reduction compared to the conventional model (Compared to the IZS31 series at the installation height of 300 mm) Potential amplitude is reduced with SMC independent Dual AC type sensor. Static electricity elimination may be achieved without causing damage to a device which is sensitive to electrostatic discharge (ESD). Potential amplitude applied to the applicable workpiece is reduced even if it the workpiece is mounted within close proximity of the ionizer. Independent Dual AC type...
Open the catalog to page 2_ . f_0_. (High speed static electricity Feedback SenSOr type Series /Zo4 7 elimination specification)^ Note) An ion balance sensor 'Rapid elimination of static electricity by a feedback sensor The speed of static electricity elimination has been increased by reading the workpiece's electrostatic potential by the feedback sensor (option) and continuously emitting ions with a reverse polarity. With sensor Without sensor Without sensor With sensor Feedback sensor Detects the polarity of a discharged object Supply pressure: 0.1 MPa Operation frequency: 30 Hz Electrode cartridge with rapid...
Open the catalog to page 3Reduction of adjustment and maintenance labor by auto balance sensor 'S? « Built-in type (Standard) The sensor is installed within the ionizer body and may be mounted anywhere. Monitoring the amount of ion emitted from an ionizer, the autobalance sensor maintains the initial ion balance by adjusting the +/- ion supply rate. Monitoring +/- return current rHigh accuracy type (Option) • The ion balance near the workpiece is accurately adjusted. • The object is not affected by the height of installation or any disturbance interference Auto balance sensor Low maintenance electrode cartridges are...
Open the catalog to page 4Refer to Features 5 for Models and Functions. Setting ionizer with remote controller “Ion balance adjustment at external signal input” or “Ion balance adjustment at any time” can be selectable. The auto balance sensor may be connected only when adjusting the ion balance. Automatic ion balancing by means of signal input Ion balance value (V) IZS 42 Total number of ionizers that may be connected IZS41: Max. 8 units. IZS42: Max. 5 units. 25 0 May be used to adjust and set several ionizers remotely. Can recognize and control up to 16 ionizers through address setting. Frequency setting Ion...
Open the catalog to page 5Ionizer Series IZS40/41/42 Models and Functions IZS42 IZS41 IZS40 Series Method of applying voltage Sensor (Auto balance) Dual AC AC, Sensing AC, DC AC, DC Built-in type (Standard) — High accuracy type (Option) — Feedback sensor (Option) — I/O — Transition wiring may be used. Note 1) — Electrode needle contamination detector — Incorrect high voltage ion discharge detection Low maintenance electrode Energy saving type de-ionizing Cartridge High speed de-ionizing With one-touch fitting (ø6, ø8, ø10) Bracket mount Non-standard bar length (Made to Order) Note 1) Order transition wiring...
Open the catalog to page 6Application Examples Eliminating static electricity from films Eliminating static electricity on film molded goods · Prevents adhesion of dust. · Prevents winding failure due to wrinkles etc. · Prevents attaching to conveyer. · Prevents dispersion of finished goods. Eliminating static electricity during wafer transfer Eliminating static electricity from packing films · Prevents breakage due to discharge between wafers and hands. · Prevents the filled substance from adhering to the packing film. · Reduces packing mistakes. Eliminating static electricity from lens Eliminating static...
Open the catalog to page 7Series IZS40/41/42 Technical Data Static Electricity Elimination Characteristics Note) Static electricity elimination features are based on the data using the charged plate (size: 150 mm x 150 mm, capacitance: 20 pF) as defined in the U.S. ANSI standards (ANSI/ESD, STM3.1-2006). Use this as a guideline purpose only for model selection because the value varies depending on the material and/or size of a subject. q Installation Distance and De-ionization Time (Electricity Elimination from 1000 V to 100 V) IZS40, 41 Static electricity elimination time (sec) 1) Without air purge 20 18 16 14 12...
Open the catalog to page 8Technical Data Series IZS40/41/42 2) With high speed de-ionizing cartridge, With air purge- Supply pressure: 0.1 MPa (8.6 L/min [ANR] per cartridge) 3) With energy saving type de-ionizing cartridge, With air purge- Supply pressure: 0.1 MPa (4.3 L/min [ANR] per cartridge) Supply pressure: 0.3 MPa (17.6 L/min [ANR] per cartridge) Supply pressure: 0.3 MPa (8.6 L/min [ANR] per cartridge) Supply pressure: 0.5 MPa (26.4 L/min [ANR] per cartridge) Supply pressure: 0.5 MPa (13.3 L/min [ANR] per cartridge)
Open the catalog to page 9Series IZS40/41/42 Static Electricity Elimination Characteristics Note) Static electricity elimination features are based on the data using the charged plate (size: 150 mm x 150 mm, capacitance: 20 pF) as defined in the U.S. ANSI standards (ANSI/ESD, STM3.1-2006). Use this as a guideline purpose only for model selection because the value varies depending on the material and/or size of a subject. w Static Electricity Elimination Range IZS40, 41 Frequency: 30 Hz 250 200 150 100 0 50 50 0 50 100 150 200 250 Installation distance in depth from ionizer to workpiece - Charged object location (mm)...
Open the catalog to page 10All SMC PNEUMATIC catalogs and technical brochures
-
SYJ300/500/700 Series
62 Pages
-
Vacuum Unit ZK2 Series
60 Pages
-
Air Cylinder CJ2 Series
117 Pages
-
AS-FS Series
36 Pages
-
IDF series
12 Pages
-
MHL2 Series
24 Pages
-
JCM Serie
18 Pages
-
EX245 Series
12 Pages
-
Pin Cylinder CJP2/CDJP2/CJP
19 Pages
-
5 Port Solenoid Valve VQC
63 Pages
-
5 Port Solenoid Valve VQ
79 Pages
-
SY
268 Pages
-
5-p0979-0980-hep500
2 Pages
-
5-p0977-0978-aep100
2 Pages
-
5-p0966-0971-lmu
5 Pages
-
5-p0960-0966-alb900
6 Pages
-
5-p0956-0960-ald600
5 Pages
-
5-p0948-0950-al800
3 Pages
-
es70-44c-vx2
52 Pages
-
es50-37-kq2
124 Pages
-
ex-pcw
23 Pages
-
1-p2124-2152-ex510
29 Pages
-
1-p2111-2122-ex500
12 Pages
-
1-p2063-2073-ex260
11 Pages
-
4-p0147-0178-msu-mds
32 Pages
-
es20-230b-crb2
59 Pages
-
1-p1869-1878-vp3145
10 Pages
-
VP300/500/700 series
42 Pages
-
1-p1789-1829-vqz100
41 Pages
-
1-p1727-1788-syj300
62 Pages
-
5 Port Solenoid Valve S0700
111 Pages
-
5 Port Solenoid Valve VF
59 Pages
-
5 Port Solenoid Valve SV
127 Pages
-
VH
9 Pages
-
CUJ
41 Pages
-
AL
3 Pages
-
kj mm
9 Pages
-
AQ
4 Pages
-
SY3000/5000-X13
2 Pages
-
Series MB
24 Pages
-
Series LES
23 Pages
-
Series LEFB
16 Pages
-
Series PF3W
28 Pages
-
Series IDG?A/IDG
56 Pages
-
Floating Joint
7 Pages
-
Series LEY
7 Pages
-
Series VHS
12 Pages
-
Series CY1S
28 Pages
-
SeriesCQ2/CQS/CQ
4 Pages
-
In-line Air Filter
12 Pages
-
5 Port Solenoid Valve
60 Pages
-
Series CQ2/CQS
2 Pages
-
AS series
2 Pages
-
corporate guide
13 Pages
-
ZP
69 Pages
-
ZFA
14 Pages
-
ZA
13 Pages
-
MHF
32 Pages
-
MHZ
68 Pages
-
CRB
44 Pages
-
D
117 Pages
-
RB
23 Pages
-
CEP
44 Pages
-
RSK
30 Pages
-
CLK
51 Pages
-
MK
20 Pages
-
GLJ
65 Pages
-
MGJ
7 Pages
-
Mx
36 Pages
-
MXH
18 Pages
-
My3
56 Pages
-
my1b
20 Pages
-
CC
15 Pages
-
J
14 Pages
-
CQ2
51 Pages
-
standard cylinder
84 Pages
-
VFN
6 Pages
-
SY3000
246 Pages
-
SJ3A6
18 Pages
-
1301/IW
14 Pages
-
CHQ/CHDQ
19 Pages
-
AC
95 Pages
-
HAW
4 Pages
-
HAA
3 Pages
-
ZB
24 Pages
-
CRB2
35 Pages
-
CJ1
5 Pages
-
SYJ
62 Pages
-
SJ
78 Pages