Miniature Guide Rod Cylinder > Integral wiring/piping Series Variations

Miniature Guide Rod Cylinder /limature Guide Miniature Guide Rod Cylinder Bore size Number of auto switches Auto switch type Refer to the following table ® and (2). Without auto switch (Built-in magnet) * Select the applicable auto switch from the table below. Table © Standard Strokes Table 2 Intermediate Stroke (by the 1 mm stroke) * The minimum auto switch mounting stroke is 4 mm. Applicable Auto Switches/Refer to pages 1719 to 1827 for detailed auto switch specifications. * Auto switches marked with o are produced upon receipt of order. * When using non-applicable auto switches, please consult...

Miniature Guide Rod Cylinder Series MG J This product should not be used as a stopper. Note) Within allowable kinetic energy use only Theoretical Output Allowable Rotational Torque of Plate For the rotational torque (T) added to the plate (rod end), use a value no more than the values in the table. Operation outside of this range may cause excessive impact, which may result in the damage to the devices. Plate Non-rotating Accuracy * When extending the cylinder (initial value), non-rotating accuracy 9, without loads and deflection of guide rods, it should be a value no more than the value in the...

Allowable Kinetic Energy Plate Allowable Lateral Load When driving the cylinder with inertial load, keep kinetic energy no more than the allowable value. The area between bold lines in the below graphic shows the relation between load mass and maximum speed. When the eccentric distance (L) generates from the plate (rod end), be sure to keep the load mass (W) no more than a value in the below graphic. Operation outside of this range may cause excessive impact, which may result Allowable Eccentric Load Make sure that the load mass (W) is within the range in the graph below when there is an eccentric...

P0255-P0352-E.qxd 08.11.17 2:18 PM Page 259 Miniature Guide Rod Cylinder Series MGJ Dimensions ø6 23 + Stroke 2 x M2.5 x 0.45 through 3.5 [≅ 23.3] 18.5 + Stroke 9 + Stroke 2 x ø3.3 through Counterbore ø6.2 depth 0.5 6 4 x M3 x 0.5 depth 5 29 20.5 2 ø5 20.5 ø3 [≅ 6.7] 9 28 20.5 ø5 2 x ø1.2 (Guide air release) [Auto switch] 8.4 6.1 + Stroke 2 x M3 x 0.5 (port size) 6 9 12 14.5 MGJ ø10 2 x M3 x 0.5 through 5 [≅ 24.5] 25 + Stroke 19 + Stroke 10.5 + Stroke 2 x ø4.3 through Counterbore ø8 depth 0.5 8 4 x M4 x 0.7 depth 5 2 x ø2 through (Guide air release) MGQ ø6 MGG 3 23 23 33 MGC ø5 [≅ 6.7] MGF MGZ...

Auto Switch Proper Mounting Position (Detection at Stroke End) Auto Switch Mounting Watchmaker's screwdriver Use a watchmaker's screwdriver with a handle about 5 to 6 mm in diameter when tightening the auto switch mounting screw. Tightening torque of auto switch mounting screw should be set 0.10 to 0.20 N-m.

Specific Product Precautions Be sure to read before handling. Refer to front matters 42 and 43 for Safety Instructions and pages 3 to 11 for Actuator and Auto Switch Precautions. 1. Do not put hands or fingers, etc. between the Care should be taken that hands or fingers do not get caught in between the cylinder body and the plate when air pressure is 1. Do not scratch or dent the sliding parts of the piston rod and guide rods. Damage to seals can cause air leakage or malfunction, etc. 2. When mounting the miniature guide rod cylinder with screws, do not exceed the maximum tightening torque. (The...