Mist Spray Unit Series Intermittent spray to cutting and press gear chains, etc. Model Inlet air pressure Oil tank set pressure range Oil tank capacity (cm3) Ambient and fluid temperature Solenoid valve voltage SUP Port size 0.1 to 1.0 MPa 0.05 to 0.2 MPa Total capacity: 3000 Effective capacity: 2500 5 to 50°C 100 VAC 50/60Hz, 200 VAC 50/60Hz, 24 VDC Rc 1/4 AIR : T0604 (ø6 tube) applicable : T0425 (ø4 tube) applicable 3 x Rc 1/4 OIL AIR BLOW : T0806 (ø8 tube) applicable 8.4 7.9 Mist spray unit Control Circuit Rated voltage ON/OFF valve for air blow ON/OFF valve for oil mist Air blow circuit Pressure gauge for tank pressure For the upper and lower limit control SW turns OFF when the float is on the upper side. SW turns ON when the float goes down. Contact capacity 50 VA AC, 50 W DC Pilot valve AIR BLOW Supply pressure Pressure gauge for supply pressure Float switch Recommended Equipment It is recommended to use each mist spray unit type with the mixing valves, magnet holders, branch pipes and nylon tubes listed in the table below. Regulator for tank Fixed orifice pressure setting Mist spray unit Mixing valve Magnet holder Branch pipe Nylon tube This unit, with an oil tank and a spray ON/OFF control unit, sends oil and air to the mixing valve. This valve adjusts the amounts of oil and air from the mist spray unit using built-in oil and air needles, and also discharges oil mist from the nozzle. This magnet holder enables the mixing valve installed on the arm end to be freely attached to the iron and steel parts such as machining tools, etc. This pipe is used to separate oil and air from the mist spray unit when using several mixing valves. This tube is used for the air piping and oil piping between the mist spray unit and the mixing valve. LMU200- ON/OFF valve for oil mist Pressure Pressure gauge gauge for for tank pressure supply pressure Pilot valve AIR Supply pressure Regulator for tank Fixed orifice pressure setting OIL Oil tank Application Examples Standing type machining center (Drilling center) Horizontal machining center

Series LMU100/200 Oil Discharge Rate (Representative Value) Construction/Working Principle Conditions Oil: Turbine oil class 1 ISO VG32 Oil temperature: 26°C ON/OFF valve for air blow Pressure gauge for supply pressure Oil adjusting needle 9 Mixing valve (LMV10-) Double pipe nozzle Pilot valve Lubrication plug Pressure gauge for tank pressure Number of oil needle rotations (turns) Air flow rate (Representative Value) Oil filler strainer Oil level gauge Regulator for tank pressure setting ON/OFF valve for oil mist 10 Air adjusting needle for mist Fixed orifice ON/OFF valve for oil mist 10 Air...

Mist Spray Unit Pilot valve Pilot valve Lubrication plug Regulator for tank pressure setting ON/OFF valve for oil mist ON/OFF valve for air blow Regulator for tank pressure setting ON/OFF valve for oil mist Supply pressure gauge Supply pressure gauge Tank pressure gauge Tank pressure gauge Main Parts List No. Spare Parts/Replacement Parts Part No. Material Mist spray body Aluminum die-casted Platinum silver coated Mist spray tank Aluminum die-casted Platinum silver coated Hard glass Body seal Lubrication plug Filler seal Level gauge Type C retaining ring for hole Stainless steel 10 Pressure gauge...

Related Products Mixing Valve: Series LMV Specifications Inlet air pressure Ambient and fluid temperature AIR Port size OIL AIR BLOW 0.3 MPa Max. 5 to 60°C T0604 (ø6 tube) applicable T0425 (ø4 tube) applicable T0806 (ø8 tube) applicable LMV 1 1 0 20 Nozzle tubing construction Air blow circuit 1 Mixing valve LMV10/ With air blow circuit Flexible tubing Copper tubing Nozzle tubing length: L 20 25 30 35 Oil adjusting needle Mixing valve (LMV20-) Double pipe nozzle Air adjusting needle for mist LMV20/ Without air blow circuit Double pipe nozzle Air adjusting needle for mist T0425 (ø4 x ø2.5) Applicable...

Mist Spray Unit Magnet Holder: Series LMH Magnet holder Symbol Construction Applicable mixing valve model 1 Available LMV10 2 Not available LMV20 Branch Pipe: Series LMD