*mydirectindustry

SX series
1 /138Pages

Catalog excerpts

5 Port Solenoid Valve Rubber Seal Pilot valves are concentrated on one-side, realizing wiring into a bundle and Compact design with large flow Response time 10 ms (Representative value) High reliability and long service life exceeding 50 million cycles or more (The valve may differ from a life under actual operating conditions. It is derived from our life test data.) Improved drainage resistance copper-free applications No exhaust mist, no exhaust noise <Common exhaust type for main and pilot valve> Bright color tone and state The fittings of the cylinder ports can be changed simply for the modification of the port size or for replacement. <Body ported> Indicator light and manual Same manifold base as Series SY The characteristic values shown in the catalog are representative values, not warranting the performance.

Open the catalog to page 1

Cylinder Speed Chart Body Ported Please confirm the actual conditions with SMC Sizing Program. Bore size — upward actuation * It is when the cylinder is extending that is meter-out controlled by speed controller which is directly connected with cylinder, and its needle valve with being * The average velocity of the cylinder is what the stroke is divided by the total stroke time. * Load factor: ((Load weight x 9.8)/Theoretical force) x 100% Base Mounted (With sub-plate) Bore size upward actuation It is when the cylinder is extending that is meter-out controlled by speed controller which is directly...

Open the catalog to page 2

Cylinder Speed Chart Conditions [When using SGP (Steel pipe)]

Open the catalog to page 3

Manifold Variations Bar stock type Body Ported Individual wiring í Direct piping to the main unit of a valve. Combinations of different fittings are possible. 20 Type P. 1-6-42 SX320 SX520 SX720 Bar stock type Flat ribbon cable í A 26 pins MIL connector permits onehand wiring of external cables in a bundle. 20 P Type N P. 1-6-48 SX320 SX520 SX720 Compact bar stock type Individual wiring í The base mounting facilitates maintenance after valves are changed. Compact bar stock type Flat cable í A 26 pins MIL connector permits one-touch wiring of external cables in a bundle. Bar stock type/Common...

Open the catalog to page 6

Be sure to read before handling. For Safety Instructions and Solenoid Valve Precautions, refer to page 1-7-2. Manual Override Operation ■ Non-locking push type Manual override for solenoid B Manual override for solenoid A Push-turn locking slotted type (Type D) After pushing down, turn in the direction of the arrow. If you do not turn, the mechanism is the same as that of a non-locking push type. Manual override for solenoid B Manual override for solenoid A When locking the manual override on the push-turn locking slotted type, be sure to push it down before turning. Turning without first pushing...

Open the catalog to page 8

Common Connector Assembly for Manifold Caution With the common connector assembly all of the common lead wires are tied together and this reduces wiring time. Common connector assembly part numbers Positive common specifications Negative common specifications For single solenoid For single solenoid SX100-42-4S SX100-43-4S Common Connector Assembly Wiring When only common connector assembly is ordered, wiring should be done as shown in How to Order Common Connector Assembly the illustration to the right. Refer to “How to Use Plug Connector” on page 1-6-8 for further information on socket mounting....

Open the catalog to page 9

Be sure to read before handling. For Safety Instructions and Solenoid Valve Precautions, refer to page 1-7-2. Light/Surge Voltage Suppressor Single solenoid Light/Surge voltage suppressor prevent reverse current Single solenoid Light/Surge voltage suppressor prevent reverse current Surge voltage suppressor Surge voltage suppressor prevent reverse current Double solenoid, 3 position type Light/Surge voltage suppressor prevent reverse current Double solenoid, 3 position type Light/Surge voltage suppressor Diode to prevent reverse current Surge voltage suppressor Surge voltage suppressor Diode to...

Open the catalog to page 10

I For details about certified products conforming to international standards, Body Ported Valve Single Unit 3 position closed center 3 position exhaust center 3 position pressure center Rated voltage Common specifications Positive common Negative common Manual override slotted type Light/Surge voltage Lead wire length Lead wire length With lead wire With lead wire Without lead wire Without lead wire without connector Without connector H * The LN or MN option includes 2 sockets for single solenoid ■v valves and 3 sockets for double solenoid valves. F1: With foot bracket F2: With side bracket •Thread...

Open the catalog to page 12

Body Ported L^r-I Made to Order Specifications I ff^ I (For details, refer to pages Mote) Impact resistance: No malfunction occurred when it is tested with a drop tester in the axial direction and at the right angles to the main valve and armature in both energized and de-energized states every once for each condition. (Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 2000 Hz. Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature. (Values at the initial...

Open the catalog to page 13

Body Ported Flow Characteristics/Weight Note) [ ]: Denotes normal position. Note) [ ]: Denotes normal position.

Open the catalog to page 14

Body Ported Note) [ ]: Denotes normal position.

Open the catalog to page 15

Body Ported Connector Assembly Positive common specifications Negative common specifications For double solenoid, evinn /M /in Lead wire length For detailed information on connector assembly, refer to page 1-6-8. 3 position closed center/exhaust center/pressure center 3 position closed center 3 position exhaust center 3 position pressure center (This figure shows a closed center type Component Parts

Open the catalog to page 16

Body Ported Series SX3000/5000/7000 How to Change Port Block Assembly The cylinder port block assembly can easily be changed. When changing block assembly, correct screw torque must be achieved. Cut off the air supply to confirm that no air is left in the manifold before starting operation. Remaining air or inappropriate installation may cause an accident. Ȝ For SX5000 Port block assembly Port block assembly (Cassette type) (Thread type) SV Fittings assembly SZ Mounting screw SY SYJ SX Caution Mounting screw tightening torques SX3000(M2): 0.17 N·m SX 5 000(M3): 0.8 N·m 7 ∗ Refer to “How to Order...

Open the catalog to page 17