Air does not exhaust after removal of tubing. > The body and the threaded portion can rotate.Pipe tape is not necessary. > Tubing materialTubing O.D.Nylon, Soft nylon, Polyurethane4, 6, 踸8, 10, 12 > FluidAir1.0 MPa3.0 MPa踖5 to 60 Proof pressureAmbient and fluid temperatureThreadThread seal (Standard)Copper-free (Standard) C (No freezing)JIS B 0203 (Taper thread for piping)Mounting sectionNut sectionWith thread sealJIS B 0211 Class 2 (Metric fine thread)Brass parts are all electroless nickel plated Maximum operating pressure > BodyC3604BD, PBTC3604BD (Thread portion)Stainless steel 304Stainless steel 304, POMPOMNBRStudChuck, Spring Guide Collet, Release buttonPOM Valve, RetainerC3604BD, POM StopperSeal, O-ring >

Male connector Straight union KCH P. 69 KCH P. 60 Use to pipe in the same direction from female thread.Use to pipe at right angles to female thread.Use to connect tubes in both 90 Male elbow Straight plug for frequent use It can save tube cutting labor in the case of frequent tube installation and removal. Use to connect a self- seal fitting and a tube in the same dierection. KCL P. 69 KCH P. 60 > Union tee directions.Use to branch line in the same direction. 2 branched ports has a self-seal function.Use to add the self-seal mechanism to the usual One-touch fittings, Series KQ.Use to connect...

1. First, tighten it by hand, then give it an additional 1/6 turn with the wrench. Excessive tightening may damage the threaded portion or deform the gasket to cause air leakage. Insufficient tightening may leave the thread loosened or cause air leakage. > 1. When inserting/removing the tubing is difficult under a pressurized condition, it should be inserted or removed by lowering the pressure or after fully exhausting. > Cut the tube perpendicularly, taking care not to damage the outside surface. (Use tube cutter TK-1, 2 or 3. Do not cut the tube with cutting pliers, nippers, scissors, etc.)...

These safety instructions are intended to prevent a hazardous situation and/or equipment damage. These instructions indicate the level of potential hazard by labels of "Caution", "Warning" or "Danger" . To ensure safety, be sure to observe ISO 4414 > Note 1) , JIS B 8370 > Note 2) and other safety practices. > Operator error could result in injury or equipment damage. Operator error could result in serious injury or loss of life. In extreme conditions, there is a possible result of serious injury or loss of life. Note 1)ISO 4414: Pneumatic fluid power--General rules relating to systems.Note 2)JIS...

If the compressed air supply is contaminated with chemicals, cynthetic materials, corrosive gas, etc., it may lead to break down or malfunction. 1. Confirm the specifications. > Products represented in this catalog are designed for use in compressed air appllications only (including vacuum), unless otherwise indicated. Do not use the product outside their design parameters. Please contact SMC when using the products in applications other than compressed air (including vacuum). 1.Do not use in environments where the product is directly exposed to corrosive gases, chemicals, salt water, water or...

CE Mark The CE mark indicates that machines and components meet essential requirements of all the EC Directives applied.It has been obligatory to apply CE marks indicating conformity with EC Directives when machines and components are exported to the member Nations of the EU. Once A manufacturer himselfӔ declares a product to be safe by means of CE marking (declaration of conformity by manufacturer), free distribution inside the member Nations of the EU is permissible. CE Mark SMC provides CE marking to products to which EMC and Low Voltage Directives have been applied, in accordance with CETOP...

Mark of compliance for CSAMark of compliance for CSA/UL > TSSA (MCCR) Registration Products TSSA is the regulation in Ontario State, Canada. The products that the operating pressure is more than 5 psi (0.03 MPa) and the piping size is bigger than 1 inch. fall into the scope of TSSA regulation. Products conforming to CE StandardWith CE symbol for simple visual recognition CSA Standards & UL Standards UL and CSA standards have been applied in North America (U.S.A. and Canada) symbolizing safety of electric products, and are defined to mainly prevent danger from electric shock or fire, resulting...

SMC Pneumatics (U.K.) Ltd. 9 08-563888 FAX: 01 9 08-561185GERMANY Vincent Avenue, Crownhill, Milton Keynes, MK8 0AN, Backinghamshire, U.K. TEL: 01 SMC Pneumatik GmbH Boschring 13-15 D-6332 9 Egelsbach, GermanyTEL: 06103-4020 FAX: 06103-40213 9 ITALY SMC Italia S.p.A. 9 271365 FAX: 02- 9 271365FRANCE Via Garibaldi 62 I-20061 Carugate Milano, Italy TEL: 02- SMC Pneumatique S.A. 1 Boulevard de Strasbourg, Parc Gustave Eiffel, Bussy Saint Georges, F-77600 Marne La Vallee Cedex 3 FranceTEL: 01-64-76-10-00 FAX: 01-64-76-10-10SWEDEN SMC Pneumatics Sweden AB EkhagsvҤgen 2 9 -31, S-141 05 Huddinge, Sweden...

FINLAND 9 -85 SMC Pneumatics Finland OY 9 5-80 FAX: 0 9 -85 9 5-85 9 5NORWAY AUSTRALIA 9 354-8222 FAX: 02- SMC Pneumatics (Australia) Pty.Ltd. 9 8 9 4-571 9 PL72, Tiistinniityntie 4, SF-02231 ESP00, Finland TEL: 0 SMC Pneumatics Norway A/S 9 0-20 FAX: 67-12- 9 0-21BELGIUM (Distributor) 14-18 Hudson Avenue Castle Hill NSW 2154, Australia TEL: 02- NEW ZEALAND 9 -573-7007 FAX: 0 SMC Pneumatics (New Zealand) Ltd. 9 -573-7002TAIWAN Vollsveien 13C, Granfoss NҦringspark N-1366 LYSAKER, Norway TEL: 67-12- SMC Pneumatics N.V./S.A. 8C Sylvia Park Road Mt.Wellington Auckland, New Zealand TEL: 0 SMC Pneumatics...