MXW
22Pages

Catalog excerpts

P0087-P0168-E.qxd 08.11.17 2:09 PM Page 147 Air Slide Table Series MXW ø8, ø12, ø16, ø20, ø25 Linear guide table provides long stroke. Table rigidity is constant throughout entire stroke. MXH Long stroke (Max. 300 mm) Linear guide provides long stroke, and it obtains smooth operation without vibration. Stroke (mm) 25 50 MXU Dual piston rod • Slim design provides 2 times the force of standard cylinder. MXW8: ø8 x 2 MXW20: ø20 x 2 MXW12: ø12 x 2 MXW25: ø25 x 2 MXW16: ø16 x 2 75 100 125 150 175 200 225 250 275 300 MXW8 MXW12 MXW16 MXW20 MXW25 MXS MXQ MXF MXW MXJ MXP MXY Shock absorber MTS Table for mounting Body mounting of workpiece Machining of positioning hole Stroke adjuster Piping, Wiring Piping is possible from 2 directions. Can pipe and wire switches from the same surface. • Auto switch can be attached to either side of body. • • Thread for body mounting • 2 mounting styles (Body tapped, Through-hole) are available. Lateral piping/wiring Body tapped Axial piping Body through-hole D- -X Individual -X 147

Open the catalog to page 1

Model Selection ©If intermediate stops by external stopper are done, avoid ejection. If ejection occurs, it may cause damage. In the case slide table is stopped at intermediate positions by the external stopper then forwarded to the front, after slide table is returned to the back for just a moment to retract the stopper, supply pressure to the opposite port to operate slide table. (3) Do not use it in such a way that excessive external force or impact force could work on it. This could result in damage. Maximum allowable load and allowable moment will vary depending on workpiece mounting...

Open the catalog to page 2

08.11.17 2:09 PM Page 149 Air Slide Table Dynamic Moment Series MXW Moment due to impact of load at end of stroke. ˾ Yaw moment Mey = 1/3∗ · We x 9.8 (L 2 + B) We: Equivalent mass for impact (kg) δ : Bumper coefficient With urethane bumper (standard) = 4/100 With shock absorber = 1/100 W: Mass (kg) V: Collision speed (mm/s) Va: Average speed (mm/s) MXW8 MXW12 MXW16 MXW20 MXW25 L3 C: Moment center position distance compensation amount (mm) 10 10 14 20 28 C ∗) Correction factor (Reference value) V B: Moment center position distance compensation (mm) We amount MXW8 MXW12 MXW16 MXW20 MXW25 Mey...

Open the catalog to page 3

P0087-P0168-E.qxd 08.11.17 2:09 PM Page 150 Air Slide Table Series MXW How to Order MXW 16 100 B M9BW Made to Order Refer to page 151 for details. Port thread type Nil TN TF M thread ø8 to ø16 Rc NPT ø20, ø25 G Number of auto switches 2 pcs. 1 pc. “n” pcs. Nil S n Auto switch Without auto switch (Built-in magnet) Nil ∗ For the applicable auto switch model, refer to the table below. Bore size (Stroke (mm)) ø8 ø12 ø16 ø20 ø25 25, 50, 75, 100, 125, 150 50, 75, 100, 125, 150 75, 100, 125, 150, 175, 200 100, 125, 150, 175, 200, 225, 250 100, 125, 150, 175, 200, 225, 250, 275, 300 Option Nil B...

Open the catalog to page 4

P0087-P0168-E.qxd 08.11.17 2:09 PM Page 151 Series Air Slide Table MXW Specifications Model MXW8 MXW16 MXW20 MXW25 ø8 x 2 Bore size (mm) MXW12 ø12 x 2 ø16 x 2 ø20 x 2 ø25 x 2 ø11 or its ø17 or its ø23 or its ø28 or its ø35 or its (equivalent ) (equivalent ) (equivalent ) (equivalent ) (equivalent ) Piping port size Rc 1/8 M5 x 0.8 Fluid Air Action Double acting Operating pressure MXH 0.15 to 0.7 MPa Proof pressure 1.05 MPa MXU –10 to +60 Ambient and fluid temperature Piston speed 50 to 500 mm/s MXS Both ends urethane bumper (Standard) Shock absorber at both ends (Option) Cushion MXQ...

Open the catalog to page 5

Table Deflection (Reference Values) The graphs below show the table displacement when the static moment load is applied to the table. The graphs do not show the loadable mass. Refer to the Model Selection Table displacement due to Table displacement due to pitch moment load yaw moment load Amount of displacement on A when the load is applied at F. Amount of displacement on A when the load is applied at F. roll moment load Amount of displacement on A when the load is applied at F.

Open the catalog to page 6

P0087-P0168-E.qxd 08.11.17 2:09 PM Page 153 Air Slide Table Series MXW Option Specifications Stopper Bolt Assembly Stopper bolt assembly can be ready for the following manner. Qty. needed for stopper bolt assembly Change of adjuster assembly How to Order Stopper Bolt Assembly Parts to be Changed Standard Option (-X11) (Refer to the figure below.) Changing the stroke adjustment W/o shock absorber range from 5 mm to 15 mm for With shock absorber one side — 2 4 Replace A B Changing to the one with shock absorber 2 — Add Changing to the one with shock absorber and stroke adjustment range of 15...

Open the catalog to page 7

P0087-P0168-E.qxd Series 08.11.17 2:09 PM Page 154 MXW Option Specifications Precautions Shock Absorber Adjustment Specifications Shock absorber model RB0805 RB0806 RB1007 RB1412 RB2015 -X552 -X552 -X552 -X552 -X552 Applicable slide table MXW8 MXW12 MXW16 MXW20 MXW25 Max. absorbing energy (J) 0.98 2.94 Stroke absorption (mm) 5 6 Max. collision speed (m/sec) 5.88 19.6 58.8 7 12 Caution Do not operate in such a state that the stopper blocks and stopper bolts on both sides are removed. 15 Doing so could create shocks, which could loosen and cause damage. 0.05 to 5 Max. operating frequency...

Open the catalog to page 8

P0087-P0168-E.qxd 08.11.17 2:09 PM Page 155 Air Slide Table Series MXW Construction MXH MXU MXS MXQ MXF MXW MXJ MXP MXY MTS Component Parts 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Material Description No. Body Table End plate Stopper block Rail Guide block Rod Piston assembly Rod cover Head cap End cap Floating bushing A Floating bushing B Stopper Stopper bolt Orifice Absorber shaft Adjusting bumper Piston seal Rod seal O-ring Note Aluminum alloy Hard anodized Aluminum alloy Hard anodized Aluminum alloy Hard anodized Aluminum alloy Hard anodized High carbon chrome bearing...

Open the catalog to page 9

P0087-P0168-E.qxd 08.11.17 2:09 PM Page 156 MXW Series MXW8/Stroke: 25, 50 mm Operating port 2 x M5 x 0.8 J 10 5.5 Width across hexagon socket hole 2.5 Note) If long bolts are used, they can touch the guide block and cause malfunction, etc. Refer to the Specific Product Precautions. 4 x M4 x 0.7 thread depth 6 Note) (Insert) 6 Operating port M5 x 0.8 Operating direction A 40 25 Y Y 5.5 24 84 Operating direction A 10 4 12 5 19 22 38 (Plug: M-5P) 46 4.5 49 + 0.030 depth 0 5H9 ø5H9 + 0.030 depth 0 4.5 Width across flats 8 Operating port M5 x 0.8 Operating direction B (Plug: M-5P) B ø7 ø6.5 10...

Open the catalog to page 10