Electric Actuators Rod Type Dust/Drip proof (IP65) specification: -X5 ∗ Size: 25, 32 Mounting variations • Direct mounting: 3 directions, Bracket mounting: 3 types • Either positioning or pushing control can be selected. Possible to hold the actuator with the rod pushing to a workpiece, etc. Rod type/ In-line motor type Auto switch mountable Series LEYG Lateral end load: 5 times more∗ ∗ Compared with rod type, size 25 and 100 stroke Compatible with sliding bearing and ball bushing bearing. Compatible with moment load and stopper (sliding bearing). • Either positioning or pushing control can be selected. Possible to hold the actuator with the rod pushing to a workpiece, etc. Guide rod type Guide rod type/ In-line motor type • High output motor Dust/Drip proof (IP65) specification: -X5 (100/200/400 W) • Improved high speed transfer ability • High acceleration/deceleration compatible (5,000 mm/s2) • Pulse input/CC-Link/SSCNET III types • With internal absolute encoder (For LECSB/C/S) Series LEYG Size: 25, 32 Step Motor (Servo/24 VDC) Servo Motor (24 VDC) Guide rod type/ In-line motor type Rod type/ In-line motor type Note) LEY63 is applicable only to the in-line motor type Controller/ Driver ̈ Step data input type Series LECP6/LECA6 64 points positioning ̈ Programless type Series LECP1 14 points positioning ̈ Pulse input type Series LECPA ̈ For absolute encoder ț Pulse input type Series LECSB ț CC-Link direct input type Series LECSC ț SSCNET III type Series LECSS ̈For incremental encoder țPulse input type/ Positioning type Series LECSA

Series LEY Step Motor (Servo/24 VDC) Control of intermediate positioning and pushing is possible. High precision with ball screws (Positioning repeatability: ±0.02 mm) Non-magnetizing lock mechanism Motor mounting position selectable Top mounting type is the standard product. Prevents a workpiece from dropping. (Holding) Right side parallel type Left side parallel type Motor cover available In-line motor type Offering 2 types of actuator cables Standard cable Robotic cable (Flexible cable) Manual override screw For manual piston rod operation Adjustment operation possible when power OFF Motor...

Electric Actuators AC Servo Motor Type High output motor (100/200/400 W) Improved high speed transfer ability High acceleration/deceleration compatible (5,000 mm/s2) Pulse input/CC-Link direct input/SSCNET III types With internal absolute encoder ∗ Incremental encoder can also be selected. Work load AC servo motor Step motor Servo motor Speed Rod type/In-line motor type Added large bore size 63! 80 kg Vertical 72 kg High output motor: 400 w Max. speed: 1,000 mm/s Work load Horizontal Dust/Drip proof specification Rod type/In-line motor type

Series LEY Step Motor (Servo/24 VDC) Compact integrated guide rods Lateral load resistance and high non-rotating accuracy Compatible with sliding bearing and ball bushing bearing Sliding bearing Suitable for lateral load applications such as a stopper where shock is applied Ball bushing bearing Smooth operation suitable for pusher and lifter In-line motor type Non-rotating accuracy improved by using two guide rods Improved rigidity ∗ Lateral end load: 5 times more ∗ Compared with rod type, size 25 and 100 stroke Sliding bearing Series LEYG /Size: 25, 32 Guide rod type/ In-line motor type For...

Electric Actuators Dust/Drip proof (IP65) specification Material: Nylon Retains grease oil film. Seal connector Prevents dust and water droplets from entering between the cable and motor cover. Aluminum cover Protects the motor. Vent hole Reduces internal pressure fluctuation to prevent dust and water droplets from entering. Groove for auto switch Water resistant type (Coolant) For checking the limit and intermediate signal ∗ Order the water resistant 2-color indication solid state auto switch separately. (Refer to page 27.) LEY-X5 (Refer to page 22.) Step Motor (Servo/24 VDC) Servo Motor (24...

Step Data Input Type Simple Setting to Use Straight Away Easy Mode for Simple Setting If you want to use it right away, select “Easy Mode.” Controller setting software Step data setting, test operation, move jog and move for the constant rate can be set and operated on one screen. Start testing Step data setting Setting of jog and speed of the constant rate Move for the constant rate Example of setting the step data Simple screen without scrolling promotes ease of setting and operating. Pick up an icon from the first screen to select a function. Set up the step data and check the monitor on the...

Normal Mode for Detailed Setting Select normal mode when detailed setting is required. Step data can be set in detail. Signals and terminal status can be monitored. Parameters can be set. JOG and constant rate movement, return to origin, test operation and testing of forced output can be performed. Controller setting software Step data setting, parameter setting, monitor, teaching, etc., are indicated in different windows. Step data setup window Parameter setup window Monitoring window Multiple step data can be stored in the teaching box, and transferred to the controller. Continuous test operation...

Programless Type No programming Capable of setting up an electric actuator operation without using a PC or teaching box 1 Setting position number Setting a registered number for the stop position Maximum 14 points 2 Setting a stop position Moving the actuator to a stop position using FORWARD and REVERSE buttons Registering the stop position using SET button 16-level adjustment Position number display Position selecting switch Pulse Input Type Speed adjustment switches SET button FORWARD and REVERSE buttons Acceleration adjustment switches Series LECPA A driver that uses pulse signals to allow...

Function Step data input type LECP6/LECA6 Pulse input type LECPA Step data and parameter setting • Input from controller setting software (PC) • Input from teaching box • Select using controller operation buttons • Input from controller setting software (PC) • Input from teaching box Step data “position” setting • Input the numerical value from controller setting software (PC) or teaching box • Input the numerical value • Direct teaching • JOG teaching • Direct teaching • JOG teaching • No “position” setting required Position and speed set by pulse signal Number of step data Operation command...