Catalogs >
SMC Corporation of America >
ISE/ZSE30A series

ISE/ZSE30A series
18Pages

Catalog excerpts

2-Color Display High-Precision Digital Pressure Switch Settings can be copied to up to 10 slave sensors at once. The settings of the master sensor can be copied to the slave sensors. b Reduced setting efforts chance of set-value input error Push Adjust to set-value with buttons. Finish setting Added vacuum range. –101 kPa 1 MPa b Rated pressure range: 0.0 to –101.0 kPa Expanded pressure range for positive-pressure type to the vacuum range. b Rated pressure range: –0.100 to 1.000 MPa 2 added outputs b NPN or PNP open collector 2 outputs b NPN or PNP open collector 1 output + Analog output (1 to 5 V or 4 to 20 mA) RoHS compliant

Open the catalog to page 1

Replaceable one-touch fittings Bracket configuration allows mounting in four orientations. The clip type allows easy removal of fittings. Fitting’s type and size can be changed. One-touch fitting Lead wire Added the connector cover. Connector cover Mounting example Mounting example Lead wire with connector (2 m) Panel mount Mountable side by side without clearance 4-digit display 4-digit display allows easy reading of displayed values. Example: 0.5 MPa One opening! • Reduction of panel-cut job • Space-saving Series 30A (New) Possible to check set-value during key locking Additional...

Open the catalog to page 2

2-Color Display High-Precision Digital Pressure Switch Series ZSE30A(F)/ISE30A How to Order Output Rated pressure range ISE30A –0.1 to 1 MPa NPN open collector 1 output PNP open collector 1 output NPN open collector 2 outputs PNP open collector 2 outputs NPN open collector 1 output + Analog voltage output NPN open collector 1 output + Analog current output PNP open collector 1 output + Analog voltage output PNP open collector 1 output + Analog current output For vacuum/ compound pressure Rated pressure range ZSE30A ZSE30AF Operating manual Calibration Booklet CD-ROM certificate — — ć — — —...

Open the catalog to page 3

Series ZSE30A(F)/ISE30A Specifications Model Rated pressure range Set pressure range Withstand pressure Minimum unit setting Applicable fluid Power supply voltage Current consumption Switch output Maximum load current Maximum applied voltage Residual voltage Response time Short circuit protection Repeatability Hystere- Hysteresis mode sis Window comparator mode Note 2) Voltage output Analog output Current output ISE30A (Positive pressure) –100.0 to 100.0 kPa –0.100 to 1.000 MPa –105.0 to 105.0 kPa –0.105 to 1.050 MPa 500 kPa 1.5 MPa 0.1 kPa 0.001 MPa Air, Non-corrosive gas, Non-flammable...

Open the catalog to page 4

2-Color Display High-Precision Digital Pressure Switch Analog Output Current output Analog output [mA] Rated pressure range Range For vacuum pressure Unit display Displays present unit (only for units of kPa and MPa). Output (OUT1) display (Green) Lights up when switch output (OUT1) is turned ON. Displays the current pressure, set mode, and error code. Always use red or green display; or switch between green and red according to the output. Four different display settings are available. Output (OUT2) display (Red) Lights up when switch output (OUT2) is turned ON. button (UP) Use this button...

Open the catalog to page 5

Series ZSE30A(F)/ISE30A Internal Circuits and Wiring Examples Main circuit Main circuit Max. 28 V, 80 mA Residual voltage 1 V or less Max. 80 mA Residual voltage 1 V or less Max. 28 V, 80 mA Residual voltage 1 V or less Main circuit Main circuit Max. 80 mA Residual voltage 1 V or less ∗ The FUNC terminal is connected using a dedicated lead wire (ZS-38-5L or ZS-38-U) when the copy function is used. (Refer to “Copy function” on page 10.)

Open the catalog to page 6

2-Color Display High-Precision Digital Pressure Switch NPN (1 output) + Analog voltage output PNP (1 output) + Analog voltage output Main circuit Main circuit White OUT2 Load FUNC Max. 28 V, 80 mA Residual voltage 1 V or less Max. 80 mA Residual voltage 1 V or less Analog voltage output Output impedance: Approx. 1 kΩ Analog voltage output Output impedance: Approx. 1 kΩ NPN (1 output) + Analog current output PNP (1 output) + Analog current output Brown DC (+) Main circuit Main circuit White OUT2 Load FUNC Max. 28 V, 80 mA Residual voltage 1 V or less Max. 80 mA Residual voltage 1 V or less...

Open the catalog to page 7

Lead wire with connector C6H One-touch fitting ø6 mm straight 17.95 One-touch fitting ø4 mm ø5/32 inch elbow One-touch fitting ø6 mm elbow One-touch fitting ø1/4 inch elbow One-touch fitting ø1/4 inch straight One-touch fitting ø4 mm ø5/32 inch straight

Open the catalog to page 8

2-Color Display High-Precision Digital Pressure Switch With bracket Bracket A (Option unit part no.: ZS-38-A1) ∗ Bracket configuration allows mounting in four orientations. Bracket B (Option unit part no.: ZS-38-A2) ∗ Bracket configuration allows mounting in four orientations.

Open the catalog to page 9

Series ZSE30A(F)/ISE30A Dimensions Panel mount B Panel mount adapter (Option unit part no.: ZS-27-C) D Panel mount adapter + Front protection cover (Option unit part no.: ZS-27-D) 42.4

Open the catalog to page 10

2-Color Display High-Precision Digital Pressure Switch Panel-cut dimensions 1 pc. mounting Multiple (2 pcs. or more) horizontal mounting Multiple (2 pcs. or more) vertical mounting 0

Open the catalog to page 11

Series ZSE30A(F)/ISE30A Function Details A Copy function (F97) The settings of the master sensor can be copied to the slave sensors. It is to reduce the time taken for setting and prevent the input of wrong values. Settings can be copied to up to 10 slave sensors at once. (Max. transmission distance: 4 m) Unit 1 1) The sensors are connected by a dedicated lead wire (ZS-38-5L (for master and one slave) or ZS-38-U (for master and up to 10 slaves)). Copying is performed through a dedicated communication line. Slave (Max. 10 units) Slave-side sensor Unit 1 Gray (Line for copying) Blue Gray...

Open the catalog to page 12

2-Color Display High-Precision Digital Pressure Switch F in brackets stand for the function codes. Refer to the operating manual for how to operate and function codes in detail. G Error indication function Error name Error code Solution Shut off the power supply. After eliminating the output factor that caused the excess current, turn the power supply back on. Load current of switch output (OUT1) exceeds 80 mA. Overcurrent error Load current of switch output (OUT2) exceeds 80 mA. A pressure of ±7% F.S. of atmospheric pressure is applied in the zero-out function. (±3.5% F.S. or more for...

Open the catalog to page 13