Dual rod cylinder with guide function suitable for pick & place applications. Ball bushing bearings and slide bearings are standard for all series. Dimensions for ball bushing bearings and slide bearings are the same. Mounting from 3 directions. Twice the thrust Non-rotating accuracy ±0.1° Adjustable stroke range: 0 to −5 mm Bottom fixing (Fixed body) Top fixing (Through-hole fixing) Work can be mounted on three faces. ∗ Except CXSJ Side fixing (Fixed body A) Series Variations Series Axial foot piping Cylinder with Stable Lubrication Function (Lube-retainer) CXSJ Page Compact type Basic type With end lock Double rod type (Ball bushing bearing only) (Ball bushing bearing only)

Auto switch can be installed from 3 directions. Reverse • Symmetric mounting Note) Slide bearing, 20 mm strokes Axial piping available (06, 010) • Allowable kinetic energy, allowable load, and nonrotating accuracy are equivalent to those of CXS basic type.

Air cushion only minimally adds to full length dimension, compared with the standard type cylinder. 1 Improved allowable kinetic energy: Two to three times that of the standard type 2 Improved noise reduction: Reduction of more than 6 dB is possible Unique air cushion mechanism with no cushion ring Elimination of the cushion ring used in current type air cushions has made it possible to reduce the overall length of the cylinder while retaining all the advantages of a compact profile. Working principle Piston seal 1. When the piston is retracting, air is exhausted through both A and A' until piston...

ICXSJ Series Model Selection A Caution Theoretical output must be confirmed separately, referring to the table on page 738. Model Selection Mounting orientation Mounting orientation ► Refer to the caution notes below. Max. speed (mm/s) Up to 400 Over 400 Up to 400 Over 400 Up to 400 Over 400 Up to 400 Over 400 Up to 400 Over 400 If the cylinder is horizontally mounted and the plate end does not reach the load’s center of gravity, use the formula below to calculate the imaginary stroke L' that includes the distance between the load’s center of gravity and the plate end. Select the graph that corresponds...

Model Selection CXSJ Series Vertical Mounting CXSJM CXSJL CXSJM CXSJL CXSJM CXSJL CXSJM CXSJL

CXSJ Series Horizontal Mounting V = Up to 400 mm/s V = Up to 800 mm/s CXSJM CXSJL Graph (9) V = Over 400 mm/s; Up to 10 mm stroke CXSJM CXSJL CXSJM CXSJL Graph (13) V = Over 400 mm/s; Up to 50 mm stroke CXSJM CXSJL

Model Selection CXSJ Series CXSJM CXSJL Graph (11) V = Over 400 mm/s; Up to 30 mm stroke CXSJM CXSJL Graph (14) V = Over 400 mm/s; Up to 75 mm stroke CXSJM CXSJL Graph (15) V = Over 400 mm/s; Up to 100 mm stroke CXSJM CXSJL

ICXS Series Model Selection/Basic Type A Caution Confirmation of theoretical output is required separately. Refer to “Theoretical Output” on page 750. Basic Type: CXS Horizontal Mounting Mounting orientation * Refer to the caution notes below. Up to 400 Over 400 Up to 100 Up to 300 Up to 4001 Over 400 Up to 100 Up to 300 Upto 400 Over 400 If the cylinder is horizontally mounted and the plate end does not reach the load’s center of gravity, use the formula below to calculate the imaginary stroke L' that includes the distance between the load’s center of gravity and the plate end. Select the graph...

CXS Series Horizontal Mounting CXSM CXSL CXSM CXSL CXSM CXSL

Model Selection/Basic Type Horizontal Mounting CXSM CXSL CXSM CXSL CXSM CXSL CXSM CXSL CXSM CXSL

ICXS Series Model Selection/With Air Cushion ^ Caution utput is required separately. Refer to “Theoretical Output Table” on page 762. Mounting orientation Stroke (mm) Selection graph - Horizontal MountingMounting orientation L (Example) When using CXSM20-10 and L = 10 mm: Imaginary stroke L' = 10 + 6 + 10 = 26 Therefore, the graph used for your model selection should be the one for CXSM20-30.

Model Selection/With Air Cushion Vertical Mounting Graph (2) V = 400 mm/s CXSM CXSL CXSM CXSL CXSM CXSL CXSM CXSL

CXS Series Horizontal Mounting Graph (6) V = Up to 800 mm/s; Up to 10 st CXSM CXSL CXSM CXSL CXSM CXSL CXSM CXSL CXSM CXSL CXSM CXSL CXSM CXSL

Port thread type Standard piping Axial piping Port location CXSJM® ^l5^-lM9BWfSl-n Compact type Number of auto switches Bearing type Auto switch Without auto switch (with built-in magnet) * Refer to the below table for auto switch model numbers. Moisture Control Tube IDK Series ^ When operating an actuator with a small diameter and a short stroke at a high frequency, the dew condensation (water droplet) may occur inside the piping depending on the conditions. Simply connecting the moisture control tube to the actuator will prevent dew condensation from occurring. For details, refer to the IDK...

Specifications Non-rotating Accuracy Bore size (mm) Note) Theoretical output (N) = Pressure (MPa) x Piston area (mm2) Deflection at the Plate End An approximate plate-end deflection X without a load is shown in the graph below. Maximum Load Mass - When the cylinder is mounted as shown in the diagrams below, the maximum load mass W should not exceed the values illustrated in the graph. Note) For axial piping of CXSJD6P-D and CXSJIU10P-III, please add the following weight. CXSJD6P-Q 0.009 kg, CXSJIH10P

Dual Rod Cylinder Compact Type CXSJ Series Construction: Standard Piping CXSJM (Slide bearing) CXSJM6 CXSJL (Ball bushing bearing) CXSJL6 Piston rod B-side piston Component Parts: Standard Piping Note) Stainless steel for CXSJM6. CX2 CXW CXT Replacement Parts/Seal Kit * Seal kit includes ©, !, and @. Order the seal kit, based on each bore size. * Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S-010 (10 g)

CXSJM (Slide bearing) CXSJM15 CXSJL (Ball bushing bearing) CXSJL15 CXSJM20 to 32 CXSJL20 to 32 Component Parts: Standard Piping No. Replacement Parts/Seal Kit Model * Seal kit includes ©, ©, and ©. Order the seal kit, based on each bore size. * Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S-010 (10 g)