ISO/VDMA Cylinder Series Variations With Lock Standard variations Built-in Stainless

ISO/VDMA Cylinder: Standard Type Double Acting, Single/Double Rod Without auto switch With auto switch Built-in magnet •- Mounting style •- Bore size Refer to "Standard Stroke" on page 6-12-4. Applicable Auto Switch/Tie-rod Mounting auto switches Auto switch Without auto switch switch model, refer to the table below. upon receipt of order. 6-1 for details of applicable auto switches in addition to those listed above. Auto Switch Mounting Bracket Part No.

ISOA/DMA Cylinder: Standard Type Double Acting, Single/Double Rod Series Mounting Accessory, Cylinder Rod/Head side flange Supplied with 4 screws Female head side clevis Male head side clevis Supplied with bolt, safety device Supplied with 4 screws Without lock With lock With ball joint Supplied with two pieces Supplied with 4 screws Female head side clevis Angled head side clevis with ball joint Note) See page 6-12-9 for male head side clevis with swivel CR50. Angled head side clevis See page 6-12-8 and 24 for dimensions. See page 6-12-10 for dimensions. See page 6-12-10 for dimensions. See...

Double acting Auto Switch Mounting Refer to page 6-12-16 for "Minimum Stroke for Auto Switch Mounting". Standard Stroke ■order0! Made to Order Specifications Intermediate strokes are available. * Please consult with SMC for longer strokes.

ISOA/DMA Cylinder: Standard Type Double Acting, Single/Double Rod Series Theoretical Output Allowable Kinetic Energy Note) Theoretical out put (N) = Pressure (MPa) x Piston area (mm2) Weight/Aluminum Tube Example: Load limit at rod end when air cylinder 063 is actuated with max. the intersection of lateral axis 500 Thus the allowable load is 80 kg.

[First angle projection] Component Parts Replacement Parts: Seal Kit • Seal kits consist of items © to ® contained in one kit, and can be ordered using the order number for each respective tube bore size.

ISOA/DMA Cylinder: Standard Type Double Acting, Single/Double Rod Series Dimensions: Without Mounting Bracket [First angle projection] C95SB Bore size - Stroke C95SB Bore size - Stroke W

Dimensions: Cylinder Mounting Accessory [First angle projection] Center trunnion style (T) Head side mounting (G) Head side Head side single clevis style (C) double clevis style (D)

ISO/VDMA Cylinder: Standard Type . r*nc Double Acting, Single/Double Rod Series UUo Dimensions: Cylinder Mounting Accessory C, D, E and CR [First angle projection] Mounting style (CR): Head side clevis with ball joint

Dimensions: Cylinder Mounting Accessory DS and ES [First angle projection]

ISOA/DMA Cylinder: Standard Type Double Acting, Single/Double Rod Series Dimensions: Piston Rod Mounting Accessory [First angle projection] Rod Clevis GKM (ISO 8140), Supplied with Bolt and Safety Device Piston Rod Ball Joint KJ (ISO 8139)

Made to Order Common Specifications: -XB6: Heat Resistant Cylinder (-10 to 150°C) Heat Resistant Cylinder (-10 to 150 C) Air cylinder which changed the seal material and grease, so that it could be used even at higher temperature up to 150 from -10°C. Applicable Series

Made to Order Common Specifications: -XB6: Heat Resistant Cylinder (-10 to 150°C) Heat Resistant Cylinder (-10 to 150°C) Heat resistant cylinder Be aware that smoking cigarettes, etc. after your hands have come into contact with the grease used in this cylinder can create a gas that is Note 1) Operate without lubrication from a pneumatic system lubricator. J) Note 2) Please contact SMC for details on the maintenance intervals for this cylinder, which differ from those of the standard cylinder. Note 3) In principle, it is impossible to make built-in magnet type and the one with auto switch. But,...

Made to Order Common Specifications: -XC18: NPT Finish Piping Port 23 NPT Finish Piping Port Air cylinder which piping port Rc threads were changed to NPT threads. Applicable Series

Made to Order Common Specifications: -XC18: NPT Finish Piping Port 23 NPT Finish Piping Port NPT finish piping port Specifications: Same as standard type. Dimensions (Connection port Size) (Dimensions other than below are the same as standard type/ Standard model no. -^Details on page 6-12-2

ISO/VDMA Cylinder: Non-rotating Rod Type Double Acting, Single/Double Rod Without auto switch With auto switch Built-in magnet Bore size Auto switch auto switches Nil | Without auto switch switch model, refer to Refer to "Standard Stroke" on page 6-12-14. Applicable Auto Switch/Tie-rod Mounting * Lead wire length symbols: 0.5 m- upon receipt of order. 6-1 for details of applicable auto switches in addition to those listed above. Auto Switch Mounting Bracket Part No.

ISO/VDMA Cylinder: Non-rotating Rod Type Double Acting, Single/Double Rod Series Double acting Note) Absorbable kinetic energy by cushion mechanism is identical to double acting single rod. Weight/Aluminum Tube

Intermediate strokes are available. Auto Switch Mounting Refer to page 6-12-16 on "Minimum Strokes for Auto Switch Mounting". Theoretical Output OUT side is identical to double acting single rod. Refer to table below for IN side. Pressure (MPa) x Piston area (mm2) [First angle projection] Replacement Parts: Seal Kit * Seal kits consist of items © to © and © contained in one kit, and can be ordered using the order number for each respective tube bore size.

ISO/VDMA Cylinder: Non-rotating Rod Type Double Acting, Single/Double Rod Series Dimensions: Without Mounting Bracket [First angle projection] C95KB Bore size - Stroke C95KB Bore size - Stroke W * Refer to pages 6-12-8 to 6-12-11 for dimensions with mounting bracket and accessories.

Auto Switch Mounting Position and Mounting Height [First angle projection] Auto Switch Mounting Position Auto Switch Mounting Height Other than the applicable auto switches listed in "How to Order", the following auto switches can be mounted. For detailed specifications, refer to page 6-16-1. * With pre-wire connector is available for solid state auto switches. For details, refer to page 6-16-60. * Normally closed (NC = b contact), solid state switch (D-Y7G/Y7H type) are also available. For details, refer to page 6-16-39.