*mydirectindustry

Catalogs
smartGAS Mikrosensorik GmbH
Carbon monoxide CO 2000 ppm

Carbon monoxide CO 2000 ppm

Product catalog summary

Product Overview: The FLOWEVO Infrared Gas Sensor for Carbon Monoxide (CO) is designed for detecting CO concentrations up to 2000 ppm. It features a pre-calibrated, compact design with a 3/5 mm gas line connector and operates on a 3.3–6 V DC supply voltage. The sensor supports Modbus ASCII or RTU communication and indicates status via an LED.

Applications: This sensor is suitable for gas analysis, biogas applications, environmental monitoring, process control, and emission monitoring. Additional equipment available includes gas coolers, particle filters, gas pumps, calibration software, and mounting equipment.

Technical Specifications:

Measurement Principle: Non-Dispersive Infra-Red (NDIR), dual wavelength.
Measurement Range: 0 to 2000 ppm Full Scale.
Flow Rate: 0.1 to 1.0 l/min.
Dimensions: 156 mm x 30 mm x 50 mm.
Warm-up Time: Less than 2 minutes for start-up, less than 30 minutes for full specification.

Performance:

Digital Resolution: 1 ppm.
Response Time: t90 ≤ 11.6 s, ton ≤ 15.9 s at 0.7 l/min.
Detection Limit: ≤ 20 ppm.
Repeatability: ≤ ± 20 ppm.
Linearity Error: ≤ ± 30 ppm.
Long-term Stability: Zero ≤ ± 100 ppm, Span ≤ ± 160 ppm over 1000 hours.

Environmental and Electrical Parameters:

Operating Temperature: 0 to +50 °C.
Storage Temperature: -20 to +60 °C.
Humidity: 0 to 95% relative humidity (non-condensing).
Supply Voltage: 3.3 V to 6.0 VDC.
Power Consumption: Average < 800 mW.

Additional Information: The sensor's performance is influenced by temperature, pressure, and flow rate. It requires a stable gas dew point of less than +5°C and a clean, particle-free sample gas. Calibration is recommended at first initiation and periodically thereafter. The document notes that specifications are subject to change and advises consulting smartGAS for specific requirements.

Catalog excerpts

FLOWEVO Infrared gas Sensor Carbon monoxide CO 2000 ppm smartGAS item number: F3-222205-05000 Pre calibrated Compact Design 3/5 mm gas line connector 3.3–6 V DC supply voltage Modbus ASCII or RTU Status indicated by LED Low drift Application examples Gas analysis Biogas application Environmental monitoring Process control Emission monitoring Available equipment Gas cooler Particle filter Gas pump Calibration Software Mounting equipment smartGAS Mikrosensorik GmbH I Huenderstr. 1 I 74080 Heilbronn I Germany T +49 7131 797553-0 I F +49 7131 797553-10 I [email protected] I www.smartgas.eu Available design in support Mechanical Installation Data communication Gas pre-treatment

Open the catalog to page 1

FLOWEVO I Carbon monoxide CO I F3-222205-05000 General features Measurement principle: Non-Dispersive Infra-Red (NDIR), dual wavelength Measurement range: by flow (nearly atmospheric pressure) Flow rate: Mounting dimensions: Warm-up time: < 2 minutes (start-up time) < 30 minutes (full specification) Measuring response* Digital resolution: Linearity error (straight line deviation): Long term stability (zero): Long term stability (span): Influence of T, P, flow rate, other* Temp. dependence (zero): Temp. dependence (span): Pressure dependence: Flow rate dependence: Cross sensitivity (zero) other...

Open the catalog to page 2

Carbon monoxide CO 2000 ppm

Carbon monoxide CO 2000 ppm

Catalog excerpts

All SmartGAS Mikrosensorik GmbH catalogs and technical brochures