*mydirectindustry

Catalogs
smartGAS Mikrosensorik GmbH
Carbon monoxide CO 15 Vol.-%

Carbon monoxide CO 15 Vol.-%

Product catalog summary

Product Overview
The FLOWEVO Infrared Gas Sensor for Carbon Monoxide (CO) by smartGAS Mikrosensorik GmbH is a pre-calibrated, compact device designed for various applications including gas analysis, biogas applications, environmental monitoring, process control, and emission monitoring. It features a 3/5 mm gas line connector, operates on a 3.3–6 V DC supply voltage, and supports Modbus ASCII or RTU communication protocols. The sensor's status is indicated by an LED, and it is designed to have low drift.

Specifications

Measurement Principle: Non-Dispersive Infra-Red (NDIR), dual wavelength
Measurement Range: 0 to 15 Vol.-% Full Scale (FS)
Gas Supply: By flow at nearly atmospheric pressure
Flow Rate: 0.1 to 1.0 l/min
Mounting Dimensions: 76 mm x 30 mm x 50 mm (L x W x H)
Warm-up Time: Less than 2 minutes for start-up, less than 30 minutes for full specification

Measuring Response

Digital Resolution: 0.01 Vol.-%
Response Time: t90 (10 to 90 % FS) ≤ 9.9 s, ton (0 to 90 % FS) ≤ 16.5 s
Detection Limit: ≤ 0.06 Vol.-%
Repeatability: ≤ ± 0.1 Vol.-%
Linearity Error: ≤ ± 0.3 Vol.-%
Long Term Stability: Zero ≤ ± 0.3 Vol.-% over 1000 hours, Span ≤ ± 1.55 Vol.-% over 1000 hours

Influence of Temperature, Pressure, and Flow Rate

Temperature Dependence: Zero ≤ ± 0.03 Vol.-% per °C, Span ≤ ± 0.08 Vol.-% per °C
Pressure Dependence: + 0.134 % of actual reading per hPa
Flow Rate Dependence: ≤ ± 0.05 Vol.-% per 0.1 l/min
Gas Dew Point Requirement: Less than +5°C dew point, stable, particle-free, and clean sample gas

Electrical Parameters

Supply Voltage: 3.3 V to 6.0 VDC
Supply Current: Peak < 400 mA @ 3.3 V, < 240 mA @ 5.0 V
Inrush Current: < 600 mA
Average Power Consumption: < 800 mW
Digital Output Signal: Modbus ASCII/RTU via UART, autobaud, autoframe
Calibration: Zero and span by software

Climatic Conditions

Operating Temperature: 0 to +50 °C
Storage Temperature: -20 to +60 °C
Air Pressure: 800 to 1150 hPa
Ambient Humidity: 0 to 95% relative humidity (not condensing)

Additional Information
All specifications are subject to change without notice. The data provided is for guidance only and does not constitute a specification or an offer for sale. Recalibration is recommended at first initiation and periodically thereafter. For more information, visit the smartGAS website or contact their sales team.

Catalog excerpts

FLOWEVO Infrared gas Sensor Carbon monoxide CO 15 Vol.-% smartGAS item number: F3-222157-05000 Pre calibrated Compact Design 3/5 mm gas line connector 3.3–6 V DC supply voltage Modbus ASCII or RTU Status indicated by LED Low drift Application examples Gas analysis Biogas application Environmental monitoring Process control Emission monitoring Available equipment Gas cooler Particle filter Gas pump Calibration Software Mounting equipment smartGAS Mikrosensorik GmbH I Huenderstr. 1 I 74080 Heilbronn I Germany T +49 7131 797553-0 I F +49 7131 797553-10 I [email protected] I www.smartgas.eu Available design in support Mechanical Installation Data communication Gas pre-treatment

Open the catalog to page 1

FLOWEVO I Carbon monoxide CO I F3-222157-05000 General features Measurement principle: Non-Dispersive Infra-Red (NDIR), dual wavelength Measurement range: by flow (nearly atmospheric pressure) Flow rate: Mounting dimensions: Warm-up time: < 2 minutes (start-up time) < 30 minutes (full specification) Measuring response* Digital resolution: Linearity error (straight line deviation): Long term stability (zero): Long term stability (span): Influence of T, P, flow rate, other* Temp. dependence (zero): Temp. dependence (span): Pressure dependence: Flow rate dependence: Cross sensitivity (zero) other...

Open the catalog to page 2

Carbon monoxide CO 15 Vol.-%

Carbon monoxide CO 15 Vol.-%

Catalog excerpts

All SmartGAS Mikrosensorik GmbH catalogs and technical brochures