Application Manual

Cleaner Buff Masking tape with Plastic sheet Scraper with blade Spray Bottle Aluminum Foil Non-oven fabric SKETCH Roller Roller Handle Glass Cleaner IRUV Cut Coat / Hardener Other Tools Remover Kitchen Paper Towel Bottle refill Temperature and humidity meter Electronic scale Blue Tarp Tools of consumables should be prepared on the day before the application. In addition, blue tarp and stepladder are required by the situation.

Points before application ◆Usable Containers◆ ①Oil film remover refill container – Any container is fine as long as it won’t break when dropped ②Primer refill container – Use polypropylene (PP) or polyethylene (PE) ※For ① and ②, it is convenient to have a cap like the one in the right photo ③Mixing cup – Use polypropylene (PP) or polyethylene (PE) ※ Dispose of after use at each site ④Spray bottle – Any container is fine as long as it won’t break when dropped ⑤Stirring rod – Use a glass rod cap Oil film remover refill container Primer refill container ◆Work Environment◆ ① Place a thermometer and...

Step １ Preparation ●Tools Masking Tape With plastic sheet Blue Tarp Scraper with blade Spray bottle Kitchen Paper Towel 0) Protect the floor with a blue tarp or protective mat for tools and equipment. 1）Cover the floor with a blue tarp or masking film with tape. Ensure a minimum distance of 1 meter from the window glass surface. 2） Apply masking to the silicone parts of the window sash frame using 15 mm masking tape. ※Widely cover them to protect the adhesion of glass cleaner. ※Avoid to drop the dirty water from Masking tape with plastic sheet. ２）Covering the sealing 3）Apply 15mm masking tape...

Step1-２ Window frame protection ● Protection points before surface preparation In the figure on the left, please consider the sash frame as the gray sections and the caulking as the black sections. Sash frame The red, green, and blue lines indicate the image when 15 mm masking tape is applied. 4mm line Exceeding the limit – Not acceptable Ensure it overlaps about 2 mm onto the glass for the best result. Not adhered to the glass surface. The caulking is not covered – Not acceptable. When reapplying masking before coating, a 4 mm masking tape will be placed on the glass surface. Therefore, during...

Step Preparation１-1（Glass Cleaning） ●Tools Cleaner Buff Spray Bottle Kitchen Paper Towel 300ml container for glass cleaner 1）Put 5 ~ 10g / m² of glass cleaner to buff and polish while spraying the water to spread on the entire glass. Polish until the glass becomes hydrophilic state (do not repel the water). ※If there are the strong oil film parts, add the glass cleaner to polish. ※Edges of window require special attention (due to put silicone rubber fine particle dust or oil) 2）Wipe off the glass cleaner with squeegee. ※When the glass cleaner dry out, spray the water again and polish it. 3）Spray...

Step Preparation１-2（Glass Cleaning） ●Points for the glass cleaning ① There are grease.(Oil film) ①Put the glass cleaner to entire the glass. Picture 1. ②Spread the glass cleaner with spraying water with little pressure. Picture 2. ③See the picture 3. There is a remaining of oil film. Oil film such as red circle point. Polish with strong pressure. ※Please make sure to remove all oil film spots. ④If the glass cleaner dries out especially in the summer, use the pad with spraying water instead of using the squeegee. Note：When it is a big glass, please divide the polishing process. The remaining of...

Step２-１ Covering around the sash frame by Masking tape ●Tools ※You can use 24mm or 30mm if these can cover window frame. ※We recommend to use 3M Products for masking tape. Masking Tape With plastic sheet (selling only by Sketch) 1）Cover the silicone part with 4mm Masking tape. ※In order to suppress the oil coming out from silicone part. ※When you remove IRUV, 4mm protects the any damage from remover. 2）Cover the window frame with 40mm Masking tape. ※ Put a 40mm masking tape on the 4mm masking tape that has already been applied, overlapping about 2mm. 3）Apply the circle part ◯ in the lower left...

Step２-２ Applying Masking Tape（Around the key) ●Tools ※You can use 24mm or 30mm if these can cover key frame. ※Please use 3M Masking tape. Thin Blade of scraper 1）Apply to the masking tape around the key. Put 15mm Masking tape within 6mm from the red line－which makes the line of 4 red circle points ○. ※Apply ①Diagonal (Up)⇒ ②Vertically ⇒ ③Diagonal(Down). Please apply in order to take off the tape easily. 2）Cut off the over lined masking tape. ( The part of－－－) 3）Cover the whole key by 40mm Masking Tape. ③Diagonal Do not the lock the key completely to apply easily.

Step３ Primer ●Tools Cleaner cotton 300ml container for primer liquid 1）Put Primer to Cleaner cotton and apply to the whole window glass. ※ Apply the primer (5 ~ 10ml / ㎡) evenly so that there is no uncoated area. ※When you apply and appear the white part because the amount of liquid is large. It will be disappear when you apply IRUV Cut Coat. ※ If you see marks on the glass surface that look like the primer has been repelled after applying the primer, reapply the primer so that there are no areas where the primer is repelled. ※Checking whether there is uncoated area or not. 3） Carefully apply...

Step４ Blending（IRUV H-SP/HARDNER) ～・ The guideline for mixing and removing dust from the medium hair roller is about 5 minutes. ・～ IRUV H-SP／Hardener SKETCH Roller Roller Handle Electronic scale Aluminum Foil Glass Rods 1) Calculate glass coating 25g per 1 sqm and first roller soaking amount 30g per a new roller. Coating solution（90%） 2）Formulation ratio/ IRUV Cut Coat coating agent 90%: Hardener 10% ※ * Please keep the compounding ratio in units of 1g of electronic scales. 3）Pour IRUV Cut Coat liquid to cup, then Pour Hardener into Main liquid. Stir the mixed liquid for 20 seconds with glass...

Step４-1 Applying IRUV Cut Coat H-SP (within 3minutes) ⓪Put the required amount of liquid (25 g / ㎡) in the tray and let it suck into the special roller. * The amount (MAX) that the dedicated roller can absorb at one time is about 50g (2㎡). Step1; Undercoating ① Roll the roller diagonally ②Apply some liquid to the window glass with vertical coating ③ Apply one round trip along the sash frames at the four corners. Step１ Undercoating ①Roll the roller diagonally * Apply force and roll so that the line comes out (100% pressure). ②Roll the rollers in the vertical direction (50% pressure against ①)...