Electronic counters SLIK-73 universal counter with batching function 2 pulse counting inputs 1 programmable function input 4 counter reset sources 0 or 1 REL / OC output prescaler and digital filter RS-485 / Modbus RTU free configuration software S-Config Universal programmable counter type SLIK-73 is equipped with many modern features required in simple and advanced automatic control systems. Two counting inputs (pulse inputs) can operate in few different modes (as two independent pulse inputs or single quadrature input). Additional programmable input can change basic function of counting inputs (addition or subtraction of pulses from inputs, change the direction of counting) or to stop counting without clearing. Build in RS-485 communication interface enables controlling of all settings by host, and allows use of unit in advanced network systems. SLIK-73 is equipped with independent clearing input. The device can be equipped with one relay (or OC type) output with independent threshold, which can be used to control external devices. The counter can be configured with the local keyboard or free S-Config software via the RS-485 communication port. TECHNICAL DATA Power supply Power consumption 19V ÷ 50V DC; 16V ÷ 35V AC or 85 ÷ 260V AC/DC, all separated for 85 ÷ 260V AC/DC and 16V ÷ 35V AC power supply: max. 4,5 VA; for 19V ÷ 50V DC power supply: max. 4,5 W LED, 6 x 9 mm high, red, brightness adjustable in 8 steps Displayed values range -99999 ÷ 999999 + decimal point, with signalling of overfilling pulse, galvanically isolated: - down-up and up-down or quadrature - programmable function - counter reset - common Input levels low level: 0 V ÷ 1 V; high level: 10 V ÷ 30 V (12 mA @ 24V) Input frequency electronic sensor: 10 kHz / 5 kHz (for quadrature) contact sensor: max. 90 Hz (adjustable filter) Output (option) Power supply output Communication interface RS-485, 8N1 and 8N2, 1200 bit/s ÷ 115200 bit/s, Modbus RTU (not galvanically isolated) non-volatile memory, EEPROM type Operating temperature Storage temperature -10°C ÷ +70°C (standard), -20°C ÷ +70°C (depending on option) Protection class IP 65 (front), available additional frame IP 65 for panel cut-out sealing; IP 20 (case and connection clips) panel mounting; material: NORYL - GFN2S E1 case (WxHxD): 72 x 36 x 97 mm panel cut-out dimensions: 66,5 x 32,5 mm installation depth: min. 102 mm board thickness: standard 7 mm or other depending on used board thickness brackets (see Accessories) Data memory SIMEX Ltd., Wielopole 11, 80-556 Gdańsk, Poland, tel. (+48) 58 762-07-77, fax 58 762-07-70, ww

Electronic counters DIMENSIONS 5 Side view Case dimensions Panel cut-out dimensions 9 10 D - counter reset input C - programmable input counting inputs D - counter reset input A C - programmable input counting inputs type of outputs: 0 : no output 1 : REL 2 : OC options: 00 : no options 01 : IP 65 frame 08 : operating temp. -20°C ÷ +50°C 0P : IP 65 frame + operating temp. -20°C ÷ +50°C power supply: 3 : 24V AC/DC 4 : 85V - 260V AC/DC SIMEX Ltd., Wielopole 11, 80-556 Gdańsk, Poland, tel. (+48) 58 762-07-77, fax 58 762-07-70, www.simex.pl

Counters accessories MOUNTING PLATES SMP-147/73 maskownica 144 x 72 mm do montażu urządzeń w obudowie 72 x 36 mm BOARD THICKNESS BRACKETS / ADAPTORS SPH-07 1 ÷ 7 mm board thickness brackets (2 pcs) standard included with device SPH-05 1 ÷ 5 mm board thickness brackets (2 pcs) SPH-45 1 ÷ 45 mm board thickness brackets (2 pcs) SOFTWARE S-Config 2 is used for the simultaneous detection of devices in multiple Modbus RTU networks and allows user to change the configuration of most of them. For each detected device a list of its registers, which the user can modify, is displayed and also additional...