Electronic counters SLE-73 economical pulse counter 1 pulse counting input 1 programmable function input power supply output 24V DC prescaler and digital filter RS-485 / Modbus RTU free configuration software S-Config The SLE-73 meters have been designed exclusively for applications where a progressive counting of impulses is required. They feature two entry ports: counting and with a programmable function that can be used for resetting the meter to zero or stopping / changing its direction of travel (as required). The built-in entry port divisor with programmable value from 1 to 9999, along with an adjustable decimal point, permits a simple transfer of incoming impulses into the units required. The counter can be configured with the local keyboard or free S-Config software via the RS-485 communication port. TECHNICAL DATA Power supply Power consumption 19V ÷ 50V DC; 16V ÷ 35V AC or 85 ÷ 260V AC/DC, all separated for 85 ÷ 260V AC/DC and 16V ÷ 35V AC power supply: max. 4,5 VA; for 19V ÷ 50V DC power supply: max. 4,5 W LED, 6 x 9 mm high, red, brightness adjustable in 8 steps Displayed values range -99999 ÷ 999999 + decimal point, with signalling of overfilling pulse, galvanically isolated: - counting down-up and up-down (PNP) - programmable function (PNP) - common (COM) Input levels low level: 0 V ÷ 1 V; high level: 10 V ÷ 30 V (12 mA @ 24V) Input frequency electronic sensor: 3 kHz contact sensor: max. 90 Hz (adjustable filter) Power supply output Communication interface RS-485, 8N1 and 8N2, 1200 bit/s ÷ 115200 bit/s, Modbus RTU (not galvanically isolated) non-volatile memory, EEPROM type Operating temperature Storage temperature -10°C ÷ +70°C (standard), -20°C ÷ +70°C (depending on option) Protection class IP 65 (front), available additional frame IP 65 for panel cut-out sealing; IP 20 (case and connection clips) panel mounting; material: NORYL - GFN2S E1 case (WxHxD): 72 x 36 x 97 mm panel cut-out dimensions: 66,5 x 32,5 mm installation depth: min. 102 mm board thickness: standard 7 mm or other depending on used board thickness brackets (see Accessories) Data memory SIMEX Ltd., Wielopole 11, 80-556 Gdańsk, Poland, tel. (+48) 58 762-07-77, fax 58 762-07-70, ww

Electronic counters DIMENSIONS 5 Side view Case dimensions Panel cut-out dimensions EXAMPLARY PIN ASSIGNMENT +24V RS-485 /100mA + Uo - GND DATA DATA + - common input + programmable input (PNP) + counting input (PNP) ORDERING SLE-73-1400-1-X-XX1 options: 00 : no options 01 : IP 65 frame 08 : operating temp. -20°C ÷ +50°C 0P : IP 65 frame + operating temp. -20°C ÷ +50°C SIMEX Ltd., Wielopole 11, 80-556 Gdańsk, Poland, tel. (+48) 58 762-07-77, fax 58 762-07-70, www.simex.pl

Counters accessories MOUNTING PLATES SMP-147/73 maskownica 144 x 72 mm do montażu urządzeń w obudowie 72 x 36 mm BOARD THICKNESS BRACKETS / ADAPTORS SPH-07 1 ÷ 7 mm board thickness brackets (2 pcs) standard included with device SPH-05 1 ÷ 5 mm board thickness brackets (2 pcs) SPH-45 1 ÷ 45 mm board thickness brackets (2 pcs) SOFTWARE S-Config 2 is used for the simultaneous detection of devices in multiple Modbus RTU networks and allows user to change the configuration of most of them. For each detected device a list of its registers, which the user can modify, is displayed and also additional...