Catalogs >
SIMEX Sp. z o.o. >
MultiCon modules catalogue V1.13.043

MultiCon modules catalogue V1.13.043
21Pages

Add to favorites

Catalog excerpts

MultiCon modules catalogue V1.13.043 - 1

INPUT / OUTPUT / POWER SUPPLY / COMMUNICATION modules

Open the catalog to page 1

MultiCon modules catalogue V1.13.043 - 2

Input modules Output modules current

Open the catalog to page 2

MultiCon modules catalogue V1.13.043 - 3

Controllers, data recorders, HMI The MultiCon series includes advanced controllers and data recorders with great potential closed in small casings. MultiCon CMC has been specifically designed for advanced applications in industrial automatic control engineering. It does not mean, however, that the device cannot be applied in smaller systems. MultiCon CMC can be equipped with three isolated RS-485 interfaces which make it a perfect solution for distributed systems to work as CPU. Thanks to Ethernet interface the device can be monitored via the Internet. A wide range of input and output...

Open the catalog to page 3

MultiCon modules catalogue V1.13.043 - 4

HI slot P - power supply module — ■ slot D - communication module available modules listed below The installation of the R81 module in slot B only in the case where in the slot C another relay module (R81 or R45) was installed. B Available for PS32 and PS42 power supplies only

Open the catalog to page 4

MultiCon modules catalogue V1.13.043 - 5

Power supply modules PS3, PS31: 19V ÷ 50V DC; 16V ÷ 35V AC PS42: 85V ÷ 260V DC or AC PS42 PS3, PS31 and PS42 modules are used to supply the MultiCon. PS3 and PS31 modules can be supplied with: 19V ÷ 50V DC 16V ÷ 35V AC PS42 module can be supplied with: 85V ÷ 260V DC or AC Additionally modules contain: - service purpose input (service port), - 24V DC output, used to supply external sensors (not available in PS31), - digital input, used for digital signal measurement, - RS-485 port, used for communication with other devices using Modbus protocol. Power supply Power supply 85V÷260V AC/DC Pin...

Open the catalog to page 5

MultiCon modules catalogue V1.13.043 - 6

Input modules - universal UN3: 3 isolated universal inputs UN5: 5 isolated universal inputs On customer's request, it is possible to install modules equipped with 3 or 5 universal inputs. Each module includes a sensor for cold junction compensation. It is most advanced input module, available for the CMC. With its help user can make many different kind of measurements in each channel. This module can measure: voltage, current, resistance, temperature using resistance sensors or thermocouples. Pin description: IN_T : Cold Junction temperature sensor UN modules parameters are: - Name -...

Open the catalog to page 6

MultiCon modules catalogue V1.13.043 - 7

Input modules - current I16: 16 current inputs I24: 24 current inputs IS6: 6 isolated current inputs MultiCon can be equipped with modules having 16 or 24 non isolated or 6 isolated current inputs. To make sensor connection easier, modules I16 and I24 have inputs groupped into fours. IS6 module has all inputs separated one from another and signal polarity on it's inputs has no matter. 2 Power supply (depending on version) Examplary connection for 2 - wire sensors and IS6 module IS6 6 isolated current inputs IS6 6 isolated current inputs Current inputs parameters are: - Name - read-only...

Open the catalog to page 7

MultiCon modules catalogue V1.13.043 - 8

Input modules - voltage U16: 16 voltage inputs U24: 24 voltage inputs On customer's request, the MultiCon device can be equipped with 16 or 24 voltage input modules. To make sensor connection easier, inputs are grouped and all ground terminals are common but separated from power supply and other modules. GND +24V DC ±5% (Imax. = 200mA) digital input 0/15..24V DC GND B- Measurement range Hardware limitation Hardware resolution Internal impedance Sampling period 10 ms (CMC reads modules every 100 ms) 10 ms (CMC reads modules every 100 ms) 2 Power supply (depending on version) Connections for...

Open the catalog to page 8

MultiCon modules catalogue V1.13.043 - 9

Input modules - voltage/current UI4: 4 voltage + 4 current inputs UI8: 8 voltage + 8 current inputs UI12: 12 voltage + 12 current inputs The MultiCon UI modules include 8, 16 or 24 voltage / current inputs, mixed where half of them are voltage and half are current. To make sensor connection easier, inputs are grouped and all ground terminals are common but separated from power supply and other modules. UI8 4 current + 4 voltage inputs 2 Power supply (depending on version) 4 current + 4 voltage inputs Connections for 3 - wire sensor (voltage) Connections for 3 - wire sensor (current) Voltage...

Open the catalog to page 9

MultiCon modules catalogue V1.13.043 - 10

Input modules - thermocouple TC4: 4 thermocouple inputs TC8: 8 thermocouple inputs TC12: 12 thermocouple inputs The range of TC modules consist of 4, 8 and 12 thermocouple input modules, each equipped with 1 input for connectors temperature measurement. Primary destination of these modules is temperature measurement using thermocouple sensors, but it is also possible to measure voltage with typical thermocouple ranges. TC modules parameters are: - Name - read-only input name given by the device, - Unit - read-only field which displays „°C” or „mV”, depending on Mode parameter settings, -...

Open the catalog to page 10

MultiCon modules catalogue V1.13.043 - 11

Input modules - RTD RT4: 4 RTD inputs RT6: 6 RTD inputs The range of RTD modules consist of 4 and 6 RTD input modules. These inputs are used for temperature measurement using RTD type temperature sensors (by 2-, 3- and 4-wire method), or for resistance measurement in the ranges up to 3kΩ. The RT modules cooperate with many kinds of resistance thermometers and thanks to this, there is no need to change the module when another temperature sensor has been used, the user only needs to change the settings in the MultiCon unit. Schematic diagram for the RT4 module and MB1 Modbus port Pt100 sensor...

Open the catalog to page 11

MultiCon modules catalogue V1.13.043 - 12

Input modules - digital D8: 8 isolated digital inputs D16: 16 isolated digital inputs D24: 24 isolated digital inputs On customer's request, the MultiCon device can be equipped with modules having 8, 16 or 24 digital inputs. These inputs can be used singly, in groups of four or all inputs available in the module. The measurement results are presented in decimal system. D16 D modules parameters are: - Name - read-only input name given by the device, - Filter time - defines minimal time that has to elapse from last input state change, if this change wants to be noticed. Internal structure of...

Open the catalog to page 12

MultiCon modules catalogue V1.13.043 - 13

Input modules - universal counters CP2: 2 isolated universal counters CP4: 4 isolated universal counters The MultiCon CMC can be also equipped with modules having 2 or 4 universal counters. Each counter can be configured independently and has two counting inputs (Inp[n]1, Inp[n]2), programmable input (Prog[n]), reset input (Res[n]), where „n” means counter number from 1 to 4. The counter parameters are: - Name - read-only input name given by the device, -Unit - read-only field which displays measurement unit: pulses, - Low Limit - value determining amount of pulses, below which in logical...

Open the catalog to page 13