Simax 150
9Pages

TECHNICAL FEATURESE PRODUCTION TABLE INFORMAZIONI TECNICHE

INTRODUCTION: Out Simax150 is a sawing machine with entirely automatic high-efficiency carbide blade. This sawing machine is used in the cutting production of bars of round section, and squares. Is equipped of an automatic loader to feed the unit of cut in continuous cycle. Exemple model CUTTING SECTION: BLADE

CUTTING SPECIFICATIONS: NUMBER OF BLADE THEET MOTOR POWER CUTTING SPEED RATE RAPID SPEED RATE STROKE FEEDING OF THE MATERIAL FEEDING GRIPPER MOTOR POWER FORWARD CALIPER SIZER FEED SPEED MINIMUM WASTE LENGTH (with third axis) ELECTRICAL CONSUMPTION APROX MACHINE WEIGHT DIMENSIONI UNITA' DI TAGLIO INLET STANDARD BAR LENGTH

CUTTING HEAD: The movement of the head movement is commanded by a brushless motor (an axis) that is moving by a ball screw system, the slides is moving by a rollers recycle. This function units are lubricated automatically. The motorization of the cutting head that does turns the blade, is using a motor to varying speed by electronic inverter that allows to get a varying assembly of the number of loops of the blade in mode from can optimize the speed in operation of the material to cut, this various assembly after 50 to 170 loops per minute. The speed of the head movement is commanded by a...

MATERIAL IN-FEEDING: The material in-feeding happens by a vice mounted on two cylindrical chromium-plated slips that allow to feed the material in the consistent location to the cut. MATERIAL IN-FEEDING By means of a ball screw driven by a Brushless motor (stroke 800[mm]) No manual adjustments needed Closing material On both sides of the blade nipper closing Hydraulic nipper closing , both vertical and horizontal In-feeding unity Raise the feed unit to avoid scratches in the material In-feeding speed Automatic lubrication of clamping devices The trolley comes operated by a brushless motor...

EXHAUST DEFLECTOR CHIP CONVEYOR SMOKE EXTRACTOR REMOTE SUPPORT THIRD AXIS Via ethernet cable or wi-fi Mounted after the cutting unit, it allows to support the long pieces while they are being cut and also allows the reduction of waste by optimizing the end of the bar. The movements are all pneumatic. THIRD DISCHARGER ASSY: Auto-centring device with ball-screw drive by Servo and hydraulic gripper with variable pressure, this allow 2 functions: 1. In case of long pieces the third axis move the cut piece to open the cut and do not let touch the material to the blade. 2. Allow to reduce the...

LOADING DEVICES: BEAM LOADER Bar lenght Load capacity Automatic loading device where the operator places the bundle of bars in the cradle Round bar from Ø40 [mm] to Ø150 [mm] Square bar 40x40 [mm] or 100x100 [mm] From 3000 to 6500 [mm] (optional up to 12000 [mm]) 6000 [Kg] Single manual loader adjustment, by handwheel, based on the diameter of the bar to be cut. Possibility of covering the parts in contact with the material to avoid scratching the bar. INCLINED PLANE Capacity Automatic loading device with load capacity limited to the inclined plane Round bar from Ø40 [mm] to Ø150 [mm]...

Exemple model UNLOADER: The unloading of the cut pieces happens automatically. In the machine the trim-cuts and the scraps are discharged in one specific side while the chippings are going in one specific box only for them. To share the scrap from the good pieces there is a pneumatic deflector. The unloading is built on customer request. The Motorized belt with speed controlled by inverter Heavy duty stainless steel conveyor belt N ° 2 Unloading positions of the pieces N ° 1 position for the unloading of scraps (butting and end of bar

Exemple model The machine can be despatched with an automatic loader (stocker). 1. Take in of the bar that is deposited on the roller way (in automatic way) 2. material in-feeing to the blade 3. positioning for the trim-cut 4. vice closing 5. start of the motor of the blade 6. descent of the head till cutting all the section of the material. 7. return of the head to do the material in-feeding. 8. vice opening 9. material in-feeding 10. Vice closing with consequent resumption of the cycle from the point 4 till the point 9 in the case a special sensor senses that the bar is finished the...