Catalogs >
Siglent Technologies Co., Ltd >
USB-GPIB User Manual_Siglent

USB-GPIB User Manual_Siglent
13Pages

Add to favorites

Catalog excerpts

User's Guide USB-GPIB 适配器 USB-GPIB Adapter

Open the catalog to page 1

Open the catalog to page 2

一般安全概要本手册描述USB-GPIB适配器的基本使用注意事项以及基本使用方法。在使用设备之前请详细阅读了解此用户手册为避免造成可能的伤害请务必按照规定使用本产品。正确插拔仪器正在工作时请勿插拔当黄色LED灯在亮时表示适配器正在处于通讯此时插拔会造成数据的丢失或仪器的损坏请勿损坏本产品适配器损坏时或与适配器连接的产品损坏时请勿运行本产品请勿在潮湿环境下使用操作请勿在易燃易爆环境下操作避免起火和人身伤害请保持产品表面的清洁和干燥

Open the catalog to page 3

如怀疑本产品已经出现故障请及时联系SIGLENT服务与支持切勿自行拆机检查只有SIGLENT授权的有资质人员才能执行维修程序怀疑产品出故障时请勿进行操作。 USB-GPIB适配器简介鼎阳SIGLENTUSB-GPIB 适配器是用于集成了USB Host 接口但未集成GPIB接口的鼎阳仪器例如SDS1000系列数字示波器连接到GPIB总线控制上的设备即未集成GPIB接口的鼎阳设备扩展出GPIB接口使鼎阳仪器可通过GPIB指令更轻松地完成各项操作任务。本GPIB连接端遵循IEEE488.2标准USB 连接端遵循USB 2.0规范详细的GPIB命令请查阅配套的“远程命令控制手册”。性能特点 ·本适配器由USB Host 接口供电无需外接电源 ·本适配器可以通过鼎阳仪器的USB Host 接口进行GPIB控制 ·可通过GPIB控制器对鼎阳仪器的GPIB地址进行分配 ·可通过适配器上的LED灯获取其状态信息 ·GPIB接口只支持Device模式不支持Controller模式

Open the catalog to page 4

仪器的GPIB地址可以通过上位机进行设置本适配器默认 USB-GPIB 适配器的使用请参照如下步骤 3通讯状态在GPIB连接端有两个LED信号灯指示当前设备的通讯状态详细信息请查阅如下指示 ①红色“Power”灯灯亮表明USB-GPIB处于带电状态 ②黄色“Sys”灯灯闪烁表明处于运行状态 ①

Open the catalog to page 5

每个适配器只能对应一台仪器使用不支持通过USB集器对多台仪器进行控制如怀疑本产品已经出现故障请及时联系SIGLENT服务与支持切勿自行拆机检查。鼎阳科技有限公司保证生产和销售的产品从授权经销商发货之日起三年内附件一年不会出现材料和工艺缺陷。如产品在保修期限内确有缺陷鼎阳科技有限公司将根据保修单的详细规定提供修理或更换服务。若需要服务或索取保修单的完整副本请与最近的鼎阳科技有限公司销售或服务办事处联系。除此概要或适用的保修单中所提供的保修之外鼎阳科技有限公司不作其他任何明示或暗示的保修保证包括但不限于对适销性和特殊适用性的暗含保修。鼎阳科技有限公司对间接的、特殊的或由此产生的损坏不承担任何责任。

Open the catalog to page 6

联系我们如您在使用本产品的过程中有任何问题或需求可直接联系鼎阳公司服务与支持团队他们将为您解答产品的技术问题同时给您提供产品应用解决方案和产品培训服务。 STATEMENT Copyright c by Siglent Technologies Co.,Ltd. all rights reserved. Siglent is a regisrered trademark of Siglent Corporation. Contents in this Manual are not allowed to copy, ectract and translate before being allowed by 获取最新产品和服务资讯请登录 http://www.siglent.com

Open the catalog to page 7

General Security Overview This manual describes notes on use are basic usage Do not damage this product: When adapter is damaged or the product connect to adapter is broken, please do not use this product. of USB-GPIB Adapter. Please read fhrough this The USB-GPIB is intended for indoor use and manual before using this equipment to avod possible should be operated in dry,clean environment injury, and be sure to use this product in accordance with regulations. operated in dry, clean environment. Do not use in explosive atmosphere Connect anddisconnect properly: Please don't disconnect when...

Open the catalog to page 8

If the unit is suspected faulty, please contact SIGLENT service personnel immediately, disassemble on their own inspection. Only SIGLENT authorized qualified personnel is allowed to repair. Do not operate with suspected failure. Brief introduction of adapter SIGLENT USB-GPIB adapter is a kind of equipment that connects integrated USB host interface but not integrated GPIB interface SIGLENT instrument (such as SDS1000 series dso) to GPIB bus controller, namely extending a GPIB interface for SIGLENT instrument to make it finish all kinds of operating mission more easily via GPIB. This GPIB...

Open the catalog to page 9

·This adapter is powered by USB Host connector, no Follow the steps below when using the adapter need of extra power ·This adapter can GPIB control via USB Host interface of SIGLENT instrument ·It can allocate GPIB address of SIGLENT instrument via GPIB controller (1) Connection As shown in figure 1 below, connect USB-GPIB'S USB connector to the USB Host interface of SIGLENT instrument, and then connect the other end to GPIB bus controller. ·The status can be showed by its LED indicator ·GPIB interface only support Device mode, do not support Controller mode. Figurel Connection Diagram of...

Open the catalog to page 10

The GPIB address of instrument can be set through oscilloscope, the defaule address of this adapter is "13" . The GPIB address of instrument is set at oscilloscope side, and is saved in GPIB card. (3) Communication Status There are two LEDs at GPIB connection end to indicate the current communication status. For detailed information please refer to the indication NOTE: make sure the adapter and controller is powered off when plug out, Each adapter can only be used for one instrument, it can not control many instruments through USB concentrator. If there is a suspected failure of this...

Open the catalog to page 11

Service and Support The warranty above replaces all other warranties, Guarantee overview expressed or implied, including but not limited to any Siglent Technologies warrants each SIGLENT inplied warranty or merchantability, fitness, or manufactured and sold product against defects in adequacy for any particular purpose or use. SIGLENT material and workmanshio under normal use and shall not be liable for any special, incidental, or service for a period of three years from shipment consequential damages, whether in contract or (accessories one year). SIGLENT will either repair otherwise. The...

Open the catalog to page 12

If you need any help or have any questions when using this product, you can contact SIGLENT service department directly, they will answer your tdchnical qusetions, offer product solution and training service Siglent Technologies Co.,Ltd Add:3/F, Building 4, Antongda Industrial Zone,Liuxian3 Raod 68th District.Baoan District, Shezhen, P.R. China To get latest product and service information please

Open the catalog to page 13

USB-GPIB User Manual_Siglent 13Pages

Catalog excerpts

All Siglent Technologies Co. catalogs and technical brochures

USB-GPIB User Manual_Siglent
13Pages