Siglent SDG1000X Waveform Generators UserManual
168Pages

User Manual SDG1000X Series Function/Arbitrary Waveform Generator UM0201X-E01A

Declaration Copyright © SIGLENT TECHNOLOGIES CO., LTD. All rights reserved. Without permission, contents in this manual are not allowed to be copied, extracted or translated.

General Safety Summary Carefully read the following safety precautions to avoid any personal injuries or damages to the instrument and any product connected to it. To avoid potential hazards, please use the instrument as specified. Only qualified technical personnel should service this instrument. Avoid fire or open flame. Use properly rated power line connections. Use only the specified power line which has been approved by your local regulatory agency. Ground the Instrument. The instrument is grounded through the protective ground conductor of the power line. To avoid electric shock, the...

Safety Terms and Symbols Terms used on the instrument. Terms may appear on the instrument: DANGER: Indicates an injury or hazard that may immediately happen. WARNING: Indicates an injury or hazard that may not immediately happen. CAUTION: Indicates that a potential damage to the instrument or other property might occur. Symbols used on the instrument. Symbols may appear on the instrument: Hazardous Voltage Protective Earth Ground

Introduction to SDG1000X The manual covers the following 2 models of SDG1000X Series Function/Arbitrary Waveform Generators: SDG1032X and SDG1062X. SIGLENT‘s SDG1000X is a series of dual-channel function/arbitrary waveform generators with specifications of up to 60MHz maximum bandwidth, 150MSa/s sampling rate and 14-bit vertical resolution. The proprietary EasyPulse technology helps to solve the weaknesses inherent in traditional DDS generators when generating pulse waveforms, and the special square wave generator is capable of generating square waveforms with up to 60MHz frequency and low...

SIGLENT High precision Frequency Counter 196 kinds of built-in arbitrary waveforms Standard interfaces: USB Host, USB Device（USBTMC）, LAN（VXI-11） Optional interface: GPIB 4.3‖ display

1 Quick Start This chapter covers the following topics:  Handle Adjustment To Turn On/Off Output To Use Common Function Keys

Handle Adjustment To adjust the handle position of the SDG1000X, please grip the handle by the sides and pull it outward. Then, make the handle rotate to the desired position. Figure 1-1 Viewing Position and Carrying Position

This chapter will provide a brief introduction and description for the operation and functions of the front/rear panel. Front Panel SDG1000X has a clear and simple front panel which includes a 4.3 inch screen, menu softkeys, numeric keyboard, knob, function keys, arrow keys, and channel control area. User Interface Numeric Keyboard Arrow Keys Menu Softkeys Function Keys Channel Control Figure 1-2 Front Panel of SDG1000X

Rear Panel The rear panel provides multiple interfaces, including Counter, 10MHz In/Out, Aux In/Out, LAN, USB Device, Earth Terminal and AC Power Supply Input. 10 MHz Clock Input/Output Aux In/Out Counter Earth Terminal Figure 1-3 Rear Panel of SDG1000X AC Power Supply Input

User Interface The SDG1000X can only display parameters and waveform information for one channel at a time. The picture below shows the interface when CH1 chooses AM modulation of a sine waveform. The information displayed may vary depending on the function selected. 1 Figure 1-4 User Interface 1. Waveform Display Area Displays the currently selected waveform of each channel. 2. Channel Status Bar Indicates the selected status and output configuration of the channels. 3. Basic Waveform Parameters Area Shows the current waveform‘s parameters of each channel. Press Parameter and select the...

4. Channel Parameters Area Displays the load and output settings of the currently selected channel. Load ----Value of the output load, as selected by the user. Press Utility → Output → Load, then use the softkeys, number keys or knob to change the parameter value; or continue pressing the corresponding output key for two second to switch between High Impedance and 50Ω. High Impedance: display HiZ. Load: display impedance value (the default is 50Ω and the range is 50Ω to 100kΩ). Note: This setting does not actually change the instrument‘s output impedance of 50Ω but rather is used to...

SIGLENT 1-4 shows the parameters of ―AM modulation‖. 8. Modulation Parameters Area Shows the parameters of the current modulation function. After selecting the corresponding menu, use number keys or knob to change the parameter value.

Press Waveforms to enter the menu as Figure 1-5 shows. The example below will help familiarize with the waveform selection settings. Figure 1-5 Waveform Selections 1. Press Waveforms key and then press Sine softkey. The SDG1000X can generate sine waveforms with frequencies from 1μHz to 60MHz. By setting Frequency/Period, Amplitude/High level, Offset/Low level and Phase, a sine waveform with different parameters can be generated. Figure 1-6 Sine Display Interface 2. Press Waveforms key and then press Square softkey. The generator can generate square waveforms with frequencies from 1μHz to...

Figure 1-7 Square Display Interface 3. Press Waveforms key and then press Ramp softkey. The generator can generate ramp waveforms with frequencies from 1μHz to 500kHz and variable symmetry. By setting Frequency/Period, Amplitude/High level, Offset/Low level, Phase and Symmetry, a ramp waveform with different parameters can be generated. Figure 1-8 Ramp Display Interface 4. Press Waveforms key and then press Pulse softkey. The generator can generate pulse waveforms with frequencies from 1μHz to 12.5 MHz and variable pulse width and rise/fall times. By setting Frequency/Period, Amplitude/High...

SIGLENT a pulse waveform with different parameters can be generated. Figure 1-9 Pulse Display Interface 5. Press Waveforms key and then press Noise softkey. The generator can generate noise with a 60MHz bandwidth. By setting Stdev and Mean, noise with different parameters can be generated. Figure 1-10 Noise Display Interface 6. Press Waveforms key and then press Page 1/2, last press the DC softkey. The generator can generate a DC signal with a level up to ±10V into a HighZ load or ±5V into a 50Ω load.