Siglent SDG1000X Waveform Generators QuickStart
20Pages

{{requestButtons}}

Catalog excerpts

Siglent SDG1000X Waveform Generators QuickStart - 1

SDG1000X Series Function/Arbitrary Waveform Generator Quick Start

Open the catalog to page 1
Siglent SDG1000X Waveform Generators QuickStart - 2

c SIGLENT TECHNOLOGIES CO., LTD. All rights reserved. Information in this publication replaces all previous corresponding material. SIGLENT reserves the rights to change the specifications and the price. Contents of this manual are not allowed to be copied, extracted, or translated without the permission of Siglent Technologies.

Open the catalog to page 2
Siglent SDG1000X Waveform Generators QuickStart - 3

General Safety Summary Carefully read the following safety precautions to avoid any personal injuries or damages to the instrument and any product connected to it. To avoid potential hazards, please use the instrument as specified. Any service on this instrument should be performed by qualified repair personnel only. Avoid exposing this instrument to fire. Always use a proper power line voltage. Power this instrument only with the specified power line voltage approved by local regulations. Ground the Instrument. The instrument is grounded through the protective ground conductor of the power...

Open the catalog to page 3
Siglent SDG1000X Waveform Generators QuickStart - 5

Adjust the Handle When using the instrument, users can adjust the handle to a desired position for optimum use. Carrying Position Horizontal Position Figure 1 Adjust the Handle SDG1000X Quick Start-2

Open the catalog to page 5
Siglent SDG1000X Waveform Generators QuickStart - 6

The Front Panel The figure below shows the SDG1000X’s front panel layout: 1. Power Switch 2. USB Host 3. User Interface 5 6. Arrow Keys 7. CH1/CH2 Control/ Output Port 8. Channel Select Key 9. Function Keys 10. Waveform Option Key 11. Menu Softkeys Figure 2 SDG1000X Front Panel

Open the catalog to page 6
Siglent SDG1000X Waveform Generators QuickStart - 7

1.Power Switch This switch is used to turn on/off the SDG1000X. When the power switch is off, SDG1000X is in the power off state. 2.USB Host SDG1000X supports U-Disk using FAT format. It is used to read waveforms or state files from a U-Disk or store the current state of the instrument to the U-Disk. Users can update the firmware through a U-Disk. 3.User Interface SDG1000X has a 4.3 inch TFT-LCD screen, which displays current function menu, parameter settings, system state, prompts, etc. For detailed information, please refer to “User Interface”. 4.Numeric Keyboard Consists of numbers from...

Open the catalog to page 7
Siglent SDG1000X Waveform Generators QuickStart - 8

7.Channel Control Area CH1 Control/Output Key The Output key on the left is used to turn on/off CH1 output. The nominal output impedance of the BNC connector is 50 Ω. When pressing Output (the key backlight turns on), the connector outputs the waveform according to the current configuration of CH1. CH2 Control/Output Key The Output key on the right is used to turn on/off CH2 output. The nominal output impedance of the BNC connector is 50 Ω. When pressing Output (the key backlight turns on), the connector outputs the waveform according to the current configuration of CH2. CAUTION:...

Open the catalog to page 8
Siglent SDG1000X Waveform Generators QuickStart - 9

9.Function Keys Mod ----Modulation This key is used to enable the modulation screen and allow for several types of modulation. Types include AM, DSB-AM, FM, PM, ASK, FSK, PSK and PWM modulated signals. • Both “Internal” and “External” modulation sources are supported. • The corresponding key backlight will turn on when this function is selected. Sweep ----Sweep This key is used to generate sweeping frequency signals of Sine, Square, Ramp and Arbitrary functions. • The Sweep mode supports “Linear” and “Log” sweep profiles. • Sweep supports “Internal”, “External” and “Manual” trigger sources....

Open the catalog to page 9
Siglent SDG1000X Waveform Generators QuickStart - 10

Utility ----Utility Functions and System Settings This key is used to set system parameters and check version information. •Press this key and then press the help softkey to obtain built-in help information about the product. •The corresponding key backlight will turn on when this function is selected. Store/Recall ----Store and Recall Store/recall the instrument’s state or arbitrary waveform data edited by users. • Supporting the file management system, users can perform general file operations. • In addition to the built-in nonvolatile memory (C disk), an external U-Disk (D disk) can also...

Open the catalog to page 10
Siglent SDG1000X Waveform Generators QuickStart - 11

Waveforms ---- Ramp Provides ramp waveform output which ranges from 1 μHz to 500 kHz. • “Frequency/Period”, “Amplitude/High level”, “Offset/Low level”, “Phase” and “Symmetry” of the ramp waveform can be modified. Waveforms ---- Pulse Provides pulse waveform output which ranges from 1 μHz to 12.5 MHz. • “Frequency/Period”, “Amplitude/High level”, “Offset/Low level”, “Pulse Width/DutyCycle”, “Rise/Fall” and “Delay” of the pulse waveform can be modified. Waveforms ---- Noise Provides White Gaussian Noise output with a bandwidth of 60 MHz. • “Stdev” and “Mean” of the noise signal can be...

Open the catalog to page 11
Siglent SDG1000X Waveform Generators QuickStart - 12

Figure 3 SDG1000X Rear Panel

Open the catalog to page 12
Siglent SDG1000X Waveform Generators QuickStart - 13

1.Counter BNC connector. The input impedance is 1 MΩ. This connector is used to accept the signal measured by the frequency counter. 2.Aux In/Out BNC connector. The function of this connector is determined by the current operating mode of the instrument. • Sweep/Burst trigger signal input port of external trigger. • Sweep/Burst trigger signal output port of internal/manual trigger. • Burst gating trigger input port. • Synchronization output port. When synchronization is enabled, the port can output a CMOS signal with the same frequency as basic waveforms (except Noise and DC), arbitrary...

Open the catalog to page 13
Siglent SDG1000X Waveform Generators QuickStart - 14

5.AC Power Supply Input SDG1000X can accept two different types of AC input power. AC power: 100-240V, 50/60Hz or 100-120V, 400Hz Fuse: 1.25A, 250V 6.USB Device Used when connecting the instrument to an external computer to allow waveform editing ( i.e., EasyWave) and remote control. 7.LAN Interface Through this interface, the generator can be connected to a computer or network for remote control. An integrated testing system may be built, as the generator conforms to the VXI-11 class standard of LAN-based instrument control.

Open the catalog to page 14
Siglent SDG1000X Waveform Generators QuickStart - 15

User Interface SDG1000X can only display parameters and waveform of one channel at a time. The picture below shows the interface when CH1 is selected and AM modulation of a sine wave function is selected. The information displayed may vary depending on the function selected. Figure 4 User Interface 1.Waveform Display Area Displays the currently selected waveform of each channel.

Open the catalog to page 15

All Siglent Technologies Co. catalogs and technical brochures