SIEB & MEYER Unit Assembly Complying EMC EMC General Notes

Copyright Original instructions, Copyright © 2024 SIEB & MEYER AG All rights reserved. This manual or extracts thereof may only be copied with the explicit authorization by SIEB & MEYER AG. Trademarks All product, font and company names mentioned in this manual may be trademarks or registered trademarks of their respective companies. SIEB & MEYER Worldwide For questions regarding our products and technical problems please contact us. SIEB & MEYER AG Auf dem Schmaarkamp 21 21339 Lueneburg Germany Phone: +49 4131 203 0 Fax: +49 4131 203 2000 [email protected] http://www.sieb-meyer.com SIEB & MEYER...

Unit Assembly Complying EMC - General Notes

12 Safety-relevant Aspects, Residual Current Device 14.3.5 Connection to Unearthed/Asymm. Grounded Mains without Isolating 14.4.2 Connection to Grounded/Ungrounded/Asymmetrically Grounded Mains with Isolating Unit Assembly Complying EMC - General Notes

Unit Assembly Complying EMC - General Notes

1 About this Manual This chapter describes symbols, signal words and abbreviations possibly used in this manual. You can download more documentation from the SIEB & MEYER website under https:// www.sieb-meyer.com/downloads. In this manual, the warnings listed below are used. Depending on their degree of risk, the risk levels listed below exist: A Imminent risk of injury Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. ^ Follow the instructions in this manual to avoid danger. Indicates an imminently hazardous situation which, if not avoided,...

1.3 DimensionsBeside metric and inch units SIEB & MEYER uses the following units for dimensions: Abbreviation Unit Assembly Complying EMC - General Notes

Introduction SIEB & MEYER-devices only work properly and trouble-free in an EMC-compatible environment. This manual gives you valuable support in installing your devices complying to EMC. During the operation of an electronic or electric device interactions appear between the device and other nearby devices. The nearby devices act as interference source, affecting the other device as interference sink. This effect is shown in the following figure: The electromagnetic radiation emitted by device A (interference source) affects the electromagnetic immunity of device B (interference sink). Fig....

EU Directives Application of the EU directives regarding electromagnetic compatibility (EMC) with reference to SIEB & MEYER products. Basic Information The European Council enacted the EU Directives with the CE marking due to efforts to harmonize the individual national standards. The directives applying for industrial products aim to ensure the safe joint operation of electronic and mechanical apparatus without mutual interference as well as uniform safety labels of the apparatus. The EU directives are converted into bound national law in form of »harmonized standards« by the member states....

„... ‘electrical equipment’means any equipment designed for use with a voltage rating of between 50 and 1,000 V for alternating current and between 75 and 1,500 V for direct current,elektrische Betriebsmittel zur Verwendung bei einer Nennspannung...“ SIEB & MEYER-products meet the requirements of the Low-Voltage Directive 2014/35/ EU. An attestation of conformity is issued for all products.Possible peculiarities are listed in the conformity declaration. SIEB & MEYER applies the standard DIN EN 61800-2 “Adjustable speed electrical power drive systems - Part 2: General requirements”, which considers...

3.5.1 Application of the EMC Product Standard DIN EN 61800-3 SIEB & MEYER applies the EMC product standard DIN EN 61800-3 - "Adjustable speed electrical power drive systems - Part 3: EMC requirements and specific test methods", which considers the requirements of the following generic standards: Industrial, scientific and medical (ISM) radio frequency equipment To ensure conformity with the standard DIN EN 55016-2-1 / VDE 0877-16-2-1 you must use a line filter. ^ Consider the connection instructions of the line filter manufacturer to ensure sufficient filter effect. ^ SIEB & MEYER offers a number...

Regarding affixing the CE marking, Article 17 of the EMC Directive 2014/30/EU says: "1. The CE marking shall be affixed visibly, legibly and indelibly to the apparatus or to its data plate. Where that is not possible or not warranted on account of the nature of the apparatus, it shall be affixed to the packaging and to the accompanying documents. 2. The CE marking shall be affixed before the apparatus is placed on the market." The following table informs about the CE marking of products according to the EMC guideline. All SIEB & MEYER products are components that cannot be operated independently...

Stationary system According to the EMC Directive 2014/30/EU 'fixed installation' means: "aa particular combination of several types of apparatus and, where applicable, other devices, which are assembled, installed and intended to be used permanently at a predefined location;" Specific notes: ► Stationary systems must meet the basic protecting requirements of the EMC directive. ► Stationary systems do not require any formal conformity checks with CE marking and attestation of conformity. ► The compliance of the protecting requirements can be assumed for installations, if - CE markings have been...

The following figure shows a PDS setup with SIEB & MEYER drive components: PDS Machine manufacturer (OEM) Enclosure port Process measurement and control port Main power port Auxiliary power port Earth port Signal interface Power interface Other parts of PDS, e.g. motor SIEB & MEYER Basic Drive Module = frequency converter/servo drive Complete Drive Module = complete frequency converter/servo drive or CNC control Power Drive System = drive system of the machine/plant Generating high-frequency energy as by-product is the physically depending characteristics of every electronic apparatus with switched...