深圳市宇锡科技有限公司 SHENZHEN YOUSEE TECHNOLOG CO., LTD DISPLAY SPECIFICATION Product NO: (产品型号) YXM116B40-121-0102 Customer : (客 户) APPROVED BY CUSTOMER 客户签署栏 Approved by Remark 审核 备注 APPROVED BY YOUSEE 宇锡签署栏 Checked by 检查 电 子 结 构 深圳市宇锡科技有限公司 Shenzhen Yousee Technology Co.,Ltd 邹长城 LONG Tel:15818552076 E-mail: [email protected]

Shenzhen Yousee Technology Co., Ltd Product Specification RECORDS OF REVISION DATE

Shenzhen Yousee Technology Co., Ltd Product Specification 1. Application This specification applies to a color TFT-LCD Module, This Open-cell is a color active matrix LCD open-cell incorporating Oxide TFT (Thin Film Transistor).It is composed of a color TFT-LCD panel, driver ICs, a control circuit and power supply circuit. Graphics and texts can be displayed on a 1920*3x1080 dots panel with 16,777,216 colors by using eDP (Embedded Display Port) Ver1.2 interface and supplying +3.3V DC supply voltage for TFT-LCD panel driving. In this TFT-LCD panel, color filters for excellent color performance...

Shenzhen Yousee Technology Co., Ltd Product Specification 4. Input Terminals4-1 Driving interface of PWB CN1 (e [Note 4-1-1] Don’t input any signals or any powers into a NC pin. Keep the NC pin open. [Note 4-1-2] The shielding case is connected with signal GnD. • Corresponding connector: 20453-030T (I-PEX) (Panda is not responsible to its product quality, if the user applies a connector not corresponding to the above model.)

Shenzhen Yousee Technology Co., Ltd Product Specification The equivalent circuit figure of the terminal.

Shenzhen Yousee Technology Co., Ltd Product Specification T«ruination is typically lntagratad into the transmitter and racaivar Fig.4-2-3 AUX Link differential pair 5. Electrical Characteristics 5-1 Absolute Maximum Ratings (*) “Absolute Maximum Ratings” is regulations that do not exceed it even momentarily. (*) Stress beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. [Note 5-2]Backlight control signals (BL_ENABLE,BL_PWM_DIM)

Shenzhen Yousee Technology Co., Ltd Product Specification 5. DC Characteristics 5-2-1. TFT-LCD panel driving DC Electrical Characteristics

6. Backlight drivingThe backlight system is an edge-lighting type with white-LED.(It is usually required to measure under the following condition: Ta=25°C±2°C) Parameter

Shenzhen Yousee Technology Co., Ltd Product Specification LED-BL ON/OFF low voltage Input signal pin current BL_ENABLE BL_PWM_DIM [Note6-3-1] Vpwm Input : 100%= Max luminance 1%= Min luminance [Note6-3-2]The minimum value of the dimming signal pulse width is assumed regulations of the width of high and the width of low. [Note6-3-3] VCNT Input : High = BL turn on, Low or OPEN =BL turn off VBL-dip conditions

Shenzhen Yousee Technology Co., Ltd Product Specification 7. Timing characteristics of input signals7-1.Timing Characteristics Item

\ ///& Shenzhen Yousee Technology Co., Ltd Product Specification 0: Low level voltage, I: High level voltage. Each basic color can be displayed in 256 gray scales from 8 bit data signals. According to the combination of 24 bit data signals, the 16.7M color display can be achieved on the screen.

Shenzhen Yousee Technology Co., Ltd Product Specification EDID Specifications (TBD) Optical characteristics ighting the module at the following rating. *The measurement shall be taken 30 minutes after ^Condition: PWM Duty= 100% *The optical characteristics shall be measured in a dark room or equivalent. [Noie 9-1 ] Measurement of viewing angle range [Note 9-2] Measurement of luminance and Response time. Chromaticity and Contrast. Fig.91 Measurement of Viewing angle range Fig.9 2 Measurement of Contrast, Luminance, and Response time. Chromaticity, White variation, Crosstalk (Viewing angle range:...

Shenzhen Yousee Technology Co., Ltd Product Specification [Note 9-3]Definitions of viewing angle range [Note 9-4]Definition of contrast ratio: The contrast ratio is defined as the following. Luminance(Brightness) with all pixels white Luminance(Brightness) with all pixels Black [Note 9-5]Definition of response time: The response time is defined as the following figure and shall be measured by switching the input signal for "black" and "white”. Fig.9-4 Response time [Note 9-6] This shall be measured at center of the screen. [Note 9-7]Definition of white uniformity: White uniformity is defined...

Shenzhen Yousee Technology Co., Ltd Product Specification 10. Display Quality The display quality of the color TFT-LCD module shall be in compliance with the Incoming Inspection Standard. a) Be sure to turn off the power supply when inserting or disconnecting the cable. Please insert for too much stress not to join a connector in the case of insertion of a connector. b) Be sure to design the cabinet so that the module can be installed without any extra stress such as warp or twist. c) Since the front polarizer is easily damaged, pay attention not to scratch it. d) Wipe off water drop immediately....

Shenzhen Yousee Technology Co., Ltd Product Specification -The protection film must not touch driver-ICs, PWB and all components on PWB. -If adhesive may remain on the polarizer after the protection film peeling off , please remove with isopropylalcohol. Front view Caution for when bending FPC (1) Not to apply force at connection part (both panel side and PCB side) (2) Not to fold tightly (3) Please make sure to push a part where is no components on ,when sticking PCB on the back side of BL, Also, please make sure not to break other components by nail w) Precautions for Handling Tray (1) Hold...

Result Evaluation Criteria] Under the display quality test condition with normal operation state. Do not change these condition as such changes may affect practical display function. [Normal operation state] temperature : + 15~ + 35°C , Humidity : 45~75% , Atmospheric pressure : 86~106kPa

REV DATE Approval Date: Notes: 1.Unit:mm. 2.Do not scale drawing. 3.All radii without dimension R0.2. 4. n Modification Mark. 5.draft angle: 1° 6.Backlight luminance :模组200cd/m^2(Min),220cd/m^2(Typ) 7.Luminace uniformity: 75%(min)(min/max*100%) 8.UnSpecified Tolerance is ±0.2 9.Operation conditions :If= 100mA, Vf=23-27V Color coordinate:X=0.27-0.35,Y=0.27-0.35 10.All materials comply with RoHS 11.The measured value of luminace and A color coordinate bases FX's BM-7 Approval (核准) Check (检查) Design (设计) (塑胶框) (印制电路板) Wire (导线) LED (发光二极体) BEF(增光片)