深圳市宇锡科技有限公司 SHENZHEN YOUSEE TECHNOLOG CO., LTD DISPLAY SPECIFICATION Product NO: (产品型号) YX50093A Customer : (客 户) APPROVED BY CUSTOMER 客户签署栏 Approved by Remark 审核 备注 APPROVED BY YOUSEE 宇锡签署栏 Checked by 检查 电 子 结 构 深圳市宇锡科技有限公司 Shenzhen Yousee Technology Co.,Ltd 邹长城 LONG Tel:15818552076 E-mail: [email protected] Adress:深

Shenzhen Yousee Technology Co., Ltd Product Specification

Shenzhen Yousee Technology Co., Ltd Product Specification CONTENTS 目录 1.GENERAL INFORMATION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4 基本描述 2 .MODULE OUTLINE DRAWIN - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -5 产品外形图 3.INTERFACE DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -6 接口定义 4.ABSOLUTE MAXIMUM RATINGS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -7 极限参数 (IC) 5.ELECTRICAL CHARACTERISTICS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -7 模块电气特性 6.BACKLIGHT...

Shenzhen Yousee Technology Co., Ltd Product Specification 1. GENERAL INFORMATION 基本描述 Contents 内容 TFT-LCD /TRANSMISSIVE Module size 模组尺寸 Number of Dots 点阵 Outline dimensions 外形尺寸 Active area 有效区域 Pixel pitch 像素 Viewing direction 视角方向 Backlight type 背光类型 LCD Driver IC LCD 驱动 IC Interface type 接口类型

设计注意事项： 1.图中FRAME VA为推荐TP视窗位置 、大小，建议TP视窗位置、大小不 要超过FRAME VA。 2.整机机壳带泡棉产品，建议客户 机壳泡棉进入LCD单边0.5MM MIN, 防止漏光。 3.整机机壳不带泡棉产品，建议客 户整机TP的丝印黑油开窗或者LENS 丝印黑油开窗比LCD A.A区单边大 0.6MM MAX。 4.客户需保证触摸屏下表面到玻璃 上表面最少0.3MM MIN(非贴合)。 (CIRCUIT DIAGRAM) SHENZHEN YOUSEE TECHNOLOG CO.LTD

Shenzhen Yousee Technology Co., Ltd Product Specification 3. INTERFACE DESCRIPTION ^P^^

Shenzhen Yousee Technology Co., Ltd Product Specification 4. ABSOLUTE MAXIMUM RATINGS «#m(iC)_

Shenzhen Yousee Technology Co., Ltd Product Specification 6. BACKLIGHT CHARACTERISTICS 背光电气特性 Item 项目 Forward voltage 正向电压 Connection mode 连接类型 7. OPTICAL CHAYACTERISTICS 光学特性 Item Response time 响应时间 Contrast ratio Color gamut range 视角范围 LCM brightness 亮度 Chromaticity 色度坐标 Note1.Response time is the time required for the display to transition from White to black(Rise Time,Tr)and from black to wh

Shenzhen Yousee Technology Co., Ltd Product Specification FIG1. The definition of Response time 响应时间定义 Note2.contrast Ratio(CR) is defined mathematically by the following formula ,For more information see FIG2. Contrast Ratio(CR)=Average Surface Luminance with all white pixels/ Average Surface Luminance with all black pixels 备注 2.对比度是由以下公式计算所得。详见 FIG2. 对比度=显示白色画面时平均表面亮度（P1，P2,……)/显示黑色画面时平均表面亮度（P1，P2,……) FIG2. Measuring method for Contrast ratio,surface luminance,Luminance uniformity,CIE(X,Y) chromaticity. 对比度，表面亮度，均匀度，CIE 坐标测试方法 Note4.Viewing angle is the angel at which contrast ratio is greater...

Shenzhen Yousee Technology Co., Ltd Product Specification 备注 4.视角指对比度大于等于一个特定值时的可视范围，对 TFT 屏，对比对特定值为 10，对黑白屏 CSTN 屏，对比度特定值为 2，视角由横轴（X 轴），竖轴（Y 轴）同 Z 轴（垂直与 LCD 表面）之间的 夹角来定义，详见 FIG3.。 FIG3 The definition of viewing angle 视角定义 Note6.CIE(X,Y)chromaticity is the Center point value.For more information see FIG2. 备注 6.选择中心点，分别测试 X，Y 值，详见 FIG2.。 Note7.For Viewing angle and response time testing,the testing date is base on Autronic-Melchers's ConScope.Series instruments.For contrast ratio,Surface Luminance,Luminance uniformity and CIE,the testing date is base on CS-2000(BM-7/CA310) photo detector. 备注 7.视角和响应时...

Product Specification Shenzhen Yousee Technology Co., Ltd 8. Recommended Operating Sequence System Contra Display Signal Backlight Rower 1. When DISP pull “H" or “L", 1C will execute the internal power on or power off procedures Please be careful about the timing of DISP and do not interrupt it during power on or power off procedure, otherwise unexpected errors will occur 2. RGB interface Display signal: DCLK VSYNC;HSYNC, DE; DRpnf, DGf7:0}: DB[7:0] 3: LVDS interface Display signal: DCLK P/N, RX(3:0J P/N

Shenzhen Yousee Technology Co., Ltd Product Specification 8.2 Power off sequence 7/77 Symbol 1. When DISP pull “H" or “L\ 1C will execute the internal power on or power off procedures. Please be careful about the timing of DISP and do not interrupt it during power on or power off procedure, otherwise unexpected errors will occur. 2. RGB interface Display signal: DCLK VSYNC: HSYNC: DE; DR[7:0]: DG[7:0]: DB[7:0] 3. LVDS interface Display signal: DCLKP/N; RX[3:0J P/N

Shenzhen Yousee Technology Co., Ltd Product Specification 9. 1: RESET INPUT TIMING Shurtur than 5us NOTE: This section is only for reference,Details please refer to the IC specification. Input Timing

Shenzhen Yousee Technology Co., Ltd Product Specification NOTE: This section is only for reference,Details please refer to the IC specification. 备注：本节仅供参考,详细信息请参阅 IC 规格书 10. Production process control 生产过程控制管理 WORKFLOW CHART P/

Shenzhen Yousee Technology Co., Ltd Product Specification Flow Chart Related Files Form used Process Inspection Production department or Quality department Production department or Quality department Production department or storage (Production planning and control documents) (( Standard operation procedure) ((Corrective and Preventive control procedure)) (Finished goods inspection procedure) ((MX (Nonconforming Product Control Procedure) ( Reprocessing management ) ( Material handling management) First article Notices for corrective and preventive Storage lists Production design Production arrangements...

Shenzhen Yousee Technology Co., Ltd Product Specification

Shenzhen Yousee Technology Co., Ltd Product Specification lcd mm Note;The rest of the test items according to our standards 12. RELIABILITY TEST CONDITIONS

Shenzhen Yousee Technology Co., Ltd Test Item High Temperature Storage 高温存储测试 Product Specification Test Condition Inspection after test 实验后检查 Inspection after 2~4 hours storage at room temperature ,the sample shall be free from defects:实 Low Temperature Storage 低温存储测试 1.Air bubble in the LCD;模 块中有气泡 Temperature Cycle Damp Proof Test higher than initial value. 电