深圳市宇锡科技有限公司 SHENZHEN YOUSEE TECHNOLOG CO., LTD DISPLAY SPECIFICATION Product NO: (产品型号) Customer : (客 户) APPROVED BY CUSTOMER 客户签署栏 Approved by Remark 审核 备注 APPROVED BY YOUSEE 宇锡签署栏 Checked by 检查 电 子 结 构 深圳市宇锡科技有限公司 Shenzhen Yousee Technology Co.,Ltd 邹长城 LONG Tel:15818552076 E-mail: [email protected]

Shenzhen Yousee Technology Co., Ltd Product Specification CONTENT LIST Cover ----------------------------------------------------------------------------------------------1 Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification Record of Revisions Revision Version: First Edition

M. Shenzhen Yousee Technology Co., Ltd Product Specification YX50049A is a color active matrix TFT-LCD Panel using LTPS TFT's (Thin Film Transistors) as an active switching devices. This model is composed of a TFT-LCD Panel, a driving circuit and a back light system. It is a transmissive type display operating in the normal black. This TFT-LCD has a 5.0 inch diagonally measured active area with FHD resolutions (1080 horizontal by 1080 vertical pixel array). Each pixel is divided into Red, Green, Blue dots which are arranged in 1pixel 2 domain and this panel can display 16.7M colors. 1.2 Features...

Shenzhen Yousee Technology Co., Ltd Product Specification 1.3 General Specifications (H: horizontal length, V: vertical length) Parameter Pixel Pitch Active Area Pixel Arrangement Display Colors Color Gamut Display Mode Normally Black, Transmissive mode Dimensional Outline Viewing Direction (Human Eye) Note: 136.531x132.208x1.98 U/D/L/R free viewing direction 1. At the U/D/L/R direction, the viewing angle is same; 2. The TFT and CF LC Algin Direction; Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 2.0 ABSOLUTE MAXIMUM RATINGS The absolute maximum ratings are list on table as follows. When used out of the absolute maximum ratings, the LSI may be permanently damaged. Using the LSI within the following electrical characteristics limit is strongly recommended for normal operation. If these electrical characteristic conditions are exceeded during normal operation, the LSI will malfunction and cause poor reliability. If the absolute maximum rating of even is one of the above parameters is exceeded even momentarily, the quality of the...

Shenzhen Yousee Technology Co., Ltd Product Specification 3.0 ELECTRICAL SPECIFICATIONS 3.1 TFT LCD Module DC Characteristics 1. Calculator Value for reference ILED x VLED x LED Quantity = PLED 2. The LED Life-time define as the estimated time to 50% 30000hrs degradation of initial luminous. Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 4.0 INTERFACE CONNECTION4.1 Connector Part Number Connector Name / Designation Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 5.0 SIGNAL TIMING SPECIFICATIONVertical Timing Vertical Resolution=528+8xNL (VSSA=OV. VDD1=1.8V, VDD3=2.8V. TA=25°C) Nole: ( I) The VS and VBP pulse width are related to GSP and GCK timing. The GSP and GCK must be set at corresponding position for LCD normal display. Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification Note: (1) HSN^IBP must larger than 50 PCLK Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 6.0 POWER ON/OFF SEQUENCE Power on/off Sequence Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 7.0 OPTICAL SPECIFICATIONS7.1 Overview The test of Optical specifications shall be measured in a dark room(ambient luminance< 1 lux and temperature = 25±2°C) with the equipment of Luminance meter system (Topcon SR-UL1R and Westar TRD-100A) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of 0 and O equal to 0°.The center of the measuring spot on the Display surface shall stay fixed. The backlight should be operating for 30 minutes prior to measurement. 1. Viewing angle is the angle...

Shenzhen Yousee Technology Co., Ltd Product Specification 3. Surface luminance is the center point across the LCD surface 50cm from the surface with all pixels displaying white. This measurement shall be taken at the locations shown in FIG. 1. 4. Uniformity measurement shall be taken at the locations shown in FIG. 2, for a total of the measurements per display, measure surface luminance of these nine points across the LCD surface 50cm from the surface with all pixels displaying white. 5. The color chromaticity coordinates specified in Tablel shall be calculated from The spectral data measured...

Shenzhen Yousee Technology Co., Ltd Product Specification Figure 3. Response Time Testing Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 8.0 MECHANICAL CHARACTERISTICS8.1 Dimension Requirements for LCD PartMechanical outlines for the panel (H: horizontal length, V: Vertical length) Parameter Figure 5. LCM Outline Dimension (unit: mm) CfHFIDEt'mrr ZCNE I EtWBM -cl REVISIDM 1, DISPLAY HDDEi ADS Nornal Black E. OPERATING TEMPERATURE' -£0*C TO 60*C. 5. BACKLIGHT' 6 CHIP VHITE LEDS. TOLERANCE TABLEC±> Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 12.0 HANDDLING & CAUTIONS12.1 Mounting Method • The panel of the LCM consists of two thin glasses with polarizer which easily get damaged. So extreme care should be taken when handling the LCM. • Excessive stress or pressure on the glass of the LCM should be avoided. Care must be taken to insure that no torsional or compressive forces are applied to the LCM unit when it is mounted. • If the customer's set presses the main parts of the LCM, the LCM may show the abnormal display. But this phenomenon does not mean the malfunction of the LCM...