深圳市宇锡科技有限公司 SHENZHEN YOUSEE TECHNOLOG CO., LTD DISPLAY SPECIFICATION Product NO: (产品型号) Customer : (客 户) APPROVED BY CUSTOMER 客户签署栏 Approved by Remark 审核 备注 APPROVED BY YOUSEE 宇锡签署栏 Checked by 检查 电 子 结 构 深圳市宇锡科技有限公司 Shenzhen Yousee Technology Co.,Ltd 邹长城 LONG Tel:15818552076 E-mail: [email protected]

Shenzhen Yousee Technology Co., Ltd Product Specification

Shenzhen Yousee Technology Co., Ltd Product Specification

Shenzhen Yousee Technology Co., Ltd Product Specification 1 General Specifications Feature Note 1: Viewing direction for best image quality is different from TFT definition. There is a 180 degree shift. Note 2: Requirements on Environmental Protection: Q/S0002 Note 3: LCM weight tolerance: ± 5%

Shenzhen Yousee Technology Co., Ltd Product Specification 2 Input/Output Terminals 2.1 TFT LCD Panel

Shenzhen Yousee Technology Co., Ltd Product Specification Notel: I/O definition: I—Input O—Output P-—Power/Ground

Shenzhen Yousee Technology Co., Ltd Product Specification 3 Absolute Maximum Ratings 3.1 Driving TFT LCD Panel

Shenzhen Yousee Technology Co., Ltd Product Specification 4 Electrical Characteristics 4.1 Driving TFT LCD Panel

Shenzhen Yousee Technology Co., Ltd Product Specification Notel: The LED driving condition is defined for each LED channel. Note2: Under LCM operating, the stable forward current should be inputted. And forward voltage is for reference only. Note3: Optical performance should be evaluated at Ta=25°C only If LED is driven by high current, high ambient temperature & humidity condition. The life time of LED will be reduced. Operating life means brightness goes down to 50% initial brightness. Typical operating life time is estimated data. Note4: The LED driving condition is defined for each LED module....

Shenzhen Yousee Technology Co., Ltd Product Specification Block Diagram CD module diagram Shenzhen Yousee Technology Co., Ltd Product Specification

Shenzhen Yousee Technology Co., Ltd Product Specification 5 INTERFACE TIMING5.1 Serial Interface Characteristics(3-Pin serial) Parameter

Shenzhen Yousee Technology Co., Ltd Product Specification 5.2 Serial Data Transfer Interface The 3-Pin serial data packet contains a control bit DNC and a transmission byte. If DNC is low, the transmission byte is command byte. If DNC is high, the transmission byte is stored to command register. The MSB is transmitted first. The serial interface is initialized when NCS is high. In this state, SCL clock pulse or SDI/SDO data have no effect. A falling edge on NCS enables the serial interface and indicates the start of data transmission. Serial Interface protocol 3 wire serial interface (write mode)...

Shenzhen Yousee Technology Co., Ltd Product Specification 5.3 RGB Interface Characteristics5.3.1 Vertical timing for RGB I/F Item

Shenzhen Yousee Technology Co., Ltd Product Specification 5.3.2 Horizontal timing for RGB I/F Item

Shenzhen Yousee Technology Co., Ltd Product Specification

Shenzhen Yousee Technology Co., Ltd Product Specification 5.4 Reset Input Timing Note : (1).Spike due to an electrostatic discharge on NRESET line does not cause irregular system reset according to the table below: (2) Spike Rejection also applies during a valid reset pulse as shown below: (3)It is necessary to wait 5msec after releasing NRESET before sending commands. Also Sleep Out command cannot be sent for 120msec.

Shenzhen Yousee Technology Co., Ltd Product Specification 5.5 Power ON/OFF Timing

Shenzhen Yousee Technology Co., Ltd Product Specification

Shenzhen Yousee Technology Co., Ltd Product Specification Test Conditions: 1. Vf=19.2V, IF=20mA (One LED channel), the ambient temperature is 25C. 2. The test systems refer to Note 1 and Note 2.

Shenzhen Yousee Technology Co., Ltd Product Specification Note 1: Definition of optical measurement system. The optical characteristics should be measured in dark room. After 5 minutes operation, the optical properties are measured at the center point of the LCD screen. All input terminals LCD panel must be ground when measuring the center area of the panel. Photo detector Item Contrast Ratio Luminance TFT-LCD Module Chromaticity Lum Uniformity Response Time Photo detector Note 2: Definition of viewing angle range and measurement system. viewing angle is measured at the center point of the LCD...

Shenzhen Yousee Technology Co., Ltd Product Specification Note 3: Definition of contrast ratioLuminance measured when LCD is on the" White" state Contrast ratio (CR) = -;--—;-———-;————- “White state “:The state is that the LCD should be driven by Vwhite. “Black state”: The state is that the LCD should be driven by Vblack. Vwhite: To be determined Vblack: To be determined. The response time is defined as the LCD optical switching time interval between “White” state and “Black” state. Rise time (TON) is the time between photo detector output intensity changed from 90% to 10%. And fall time (TOFF)...

Shenzhen Yousee Technology Co., Ltd Product Specification Note 6: Definition of Luminance Uniformity Active area is divided into 9 measuring areas (Refer Fig. 2). Every measuring point is placed at the center of each measuring area. Luminance Uniformity (U) = Lmin/ Lmax L-------Active area length W----- Active area width Fig. 2 Definition of uniformity Lmax: The measured maximum luminance of all measurement position. Lmin: The measured minimum luminance of all measurement position. Note 7: Definition of Luminance: Measure the luminance of white state at center point.

Shenzhen Yousee Technology Co., Ltd Product Specification 7 Environmental / Reliability Test Item Functions, performance, appearance, etc. shall be free from remarkable deterioration within 50,000 hours under ordinary operating and storage conditions room temperature (25±10°C), normal humidity (45±20% RH), and in area not exposed to direct sun light. (Life time of backlight, please refer to Data about backlight.) For the final test the testing sample must be stored at room temperature for 24 hours, after the tests listed in up Table, Standard specifications for Reliability have been executed...