深圳市宇锡科技有限公司 SHENZHEN YOUSEE TECHNOLOG CO., LTD DISPLAY SPECIFICATION Product NO: (产品型号) Customer : (客 户) APPROVED BY CUSTOMER 客户签署栏 Approved by Remark 审核 备注 APPROVED BY YOUSEE 宇锡签署栏 Checked by 检查 电 子 结 构 深圳市宇锡科技有限公司 Shenzhen Yousee Technology Co.,Ltd 邹长城 LONG Tel:15818552076 E-mail: [email protected] Adress:深

Shenzhen Yousee Technology Co., Ltd Product Specification P/N:YX24010A Version: First Edition Page 2 of 22 YX-RD-001-A

Shenzhen Yousee Technology Co., Ltd Product Specification CONTENTS 目录 1.GENERAL INFORMATION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4 基本描述 2 .MODULE OUTLINE DRAWIN - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -5 产品外形图 3.INTERFACE DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -6 接口定义 4.ABSOLUTE MAXIMUM RATINGS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -7 极限参数 (IC) 5.ELECTRICAL CHARACTERISTICS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -7 模块电气特性 6.BACKLIGHT...

Shenzhen Yousee Technology Co., Ltd Product Specification 1. GENERAL INFORMATION 基本描述 Contents 内容 a-si TFT，Positive Transmissive type Number of Dots 点阵 Outline dimensions 外形尺寸 Active area 有效区域 Pixel pitch 像素 Module size 模组尺寸 Viewing direction 视角方向 Backlight type 背光类型 LCD Driver IC LCD 驱动 IC Interface type 接口类型 LCM Input voltage 模组输

设计注意事项： 1.图中FRAME VA为推荐TP视窗位置 、大小，建议TP视窗位置、大小不 要超过FRAME VA。 2.整机机壳带泡棉产品，建议客户 机壳泡棉进入LCD单边0.5MM MIN, 防止漏光。 3.整机机壳不带泡棉产品，建议客 户整机TP的丝印黑油开窗或者LENS 丝印黑油开窗比LCD A.A区单边大 0.6MM MAX。 4.客户需保证触摸屏下表面到玻璃 上表面最少0.3MM MIN(非贴合)。

Shenzhen Yousee Technology Co., Ltd Product Specification 3. INTERFACE DESCRIPTION 接口定义 System ground Chip Selected (“Low” is enable) Serial interface Clock input Serial data input/output PIN Reset Signal pin (“Low” is enable) System ground Data or command select pin. “H”: Date, “L”: Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 4. ABSOLUTE MAXIMUM RATINGS P/N:YX24010A Version: First Edition Page 7 of22 YX-RD-001-A

Shenzhen Yousee Technology Co., Ltd Product Specification 6. BACKLIGHT CHARACTERISTICS 背光电气特性 Item 项目 Forward voltage 正向电压 Connection mode 连接类型 7. OPTICAL CHAYACTERISTICS 光学特性 Item Response time 响应时间 Contrast ratio Color gamut Chromaticity 色度坐标 Note1.Response time is the time required for the

Shenzhen Yousee Technology Co., Ltd Product Specification 备注 1.响应时间是 Tr(上升时间）与 Tf(下降时间）的和，Tr 指显示黑色画面转为显示白色画面需要时 间，Tf 指显示白色画面转为显示黑色画面需要时间，详见 FIG1.。 FIG1. The definition of Response time 响应时间定义 Note2.contrast Ratio(CR) is defined mathematically by the following formula ,For more information see FIG2. Contrast Ratio(CR)=Average Surface Luminance with all white pixels/ Average Surface Luminance with all black pixels 备注 2.对比度是由以下公式计算所得。详见 FIG2. 对比度=显示白色画面时平均表面亮度（P1，P2,……)/显示黑色画面时平均表面亮度（P1，P2,……) FIG2. Measuring method for Contrast ratio,surface luminance,Luminance uniformity,CIE(X,Y) chromaticity....

Shenzhen Yousee Technology Co., Ltd Product Specification Note4.Viewing angle is the angel at which contrast ratio is greater than a specific value.For TET module,the specific value of contrast ratio is 10.For monochrome and color stn module,the specific value of contrast ratio is2.The angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface.For more information see FIG3 备注 4.视角指对比度大于等于一个特定值时的可视范围，对 TFT 屏，对比对特定值为 10，对黑白屏 CSTN 屏，对比度特定值为 2，视角由横轴（X 轴），竖轴（Y 轴）同 Z 轴（垂直与 LCD 表面）之间的夹 角来定义，详见 FIG3.。 FIG3 The definition...

Shenzhen Yousee Technology Co., Ltd Product Specification Note8.For TN type TFT transmissive module,Gray scale reverse occurs in the direction of panel viewing angle 8. Recommended Operating Sequence 8.1 Power on/off sequence with 2- power P/N:YX24010A Version: First Edition Page 11 of 22 YX-RD-001-A

Shenzhen Yousee Technology Co., Ltd Product Specification 8.2 Power on/off sequence with 3- power MIPI Active NOTE: This section is only for reference,Details please refer to the IC specification. P/N:YX24010A Version: First Edition YX-RD-001-A Page 12 of 22

Shenzhen Yousee Technology Co., Ltd Product Specification 9. RESET INPUT TIMING 9. During the Resetting period, the display wJf be blanked [The display enters the blanking sequence, which maximum time is 120 ms when Reset Starts in the Sleep Out mode. The display remains the blank state in the Sleep In mode.) and then return to Default condition for Hardware Reset. 4. Spike Rejection can also be applied dunng a valid reset pulse, as shown below: P/N:YX24010A Version: First Edition Page 13 of 22

Shenzhen Yousee Technology Co., Ltd Product Specification NOTE: This section is only for reference,Details please refer to the IC specification. 备注：本节仅供参考,详细信息请参阅 IC 规格书 10. Production process control 生产过程控制管理 WORKFLOW CHART 工作流程图 Flow Chart 流程图 Responsibility accounting 权责单位 Related Files Form used

Shenzhen Yousee Technology Co., Ltd Product Specification Production Production department or Quality department Production department or Quality department Production department or storage {Production planning and control documents)) {Corrective and Preventive control procedure » {Finished goods inspection procedure» (A {Nonconforming Product Control Procedure » {Reprocessing management » {Material handling management» First article Notices for corrective and preventive Storage lists Production arrangements P/N:YX24010A Version: First Edition Page 15 of 22 YX-RD-001-A

Shenzhen Yousee Technology Co., Ltd Product Specification D=(L+W)/2 P/N:YX24010A Version: First Edition YX-RD-001-A Page 16 of 22

Shenzhen Yousee Technology Co., Ltd Product Specification Note;The rest of the test items according to our standards 注：其余测试项按我司标准执行 12. RELIABILITY TEST CONDITIONS 可靠性测试条件 NO. Test Item Test Condition 序号 实验项目

Shenzhen Yousee Technology Co., Ltd Product Specification 1.Air bubble in the LCD;模 块中有气泡 Temperature Cycle Damp Proof Test 防潮测试 higher than initial value. 电流 IDD 大于初始值的 两倍。 测试前对样品进行外观和功能测试， 采用空气放电，对 TP 进行单次放 电，9 个点每一点放电一次，每次间 检查，如果合格就进行下一循环测 试，如果不合格，试验停止，并进行 问题判定 13. PRECAUTIONS FOR USING LCD MODULES 模组使用注意事项 1. Handing precautions 使用注意事项 1.1 The display panel is made of glass and polarizer.As glass is fragile.It tends to become or chipped during handing especially on the edges.Please avoid dropping or jarring.Do n