深圳市宇锡科技有限公司 SHENZHEN YOUSEE TECHNOLOG CO., LTD DISPLAY SPECIFICATION Product NO: (产品型号) YX21520376811FA-LP8 Customer : (客 户) APPROVED BY CUSTOMER 客户签署栏 Approved by Remark 审核 备注 APPROVED BY YOUSEE 宇锡签署栏 Checked by 检查 电 子 结 构 深圳市宇锡科技有限公司 Shenzhen Yousee Technology Co.,Ltd 邹长城 LONG Tel:15818552076 E-mail: [email protected]

Product Specification Document Revision History Change No.

Product Specification YX21520376811FA-LP8 is color active matrix thin film transistor (TFT) liquid crystal display (LCD) thal uses amorphous silicon TFT as a switching device. This model is composed of a TFT LCD panel and a driving circuit.This TFT LCD has a 21.5 (16:9) inch diagonally measured active display area with (1920 horizontal by 1080 vertical pixel) resolution. 21.5(16:9 diagonal) inch configuration Image Reversion: UP/DOWN and LEFT/RIGHT ROHS design

Note (1) Permanent damage may occur to the LCD module if beyond this specification. Functional operation should be restricted to the conditions described under normal operating conditions. (3) Test condition: LED Current 220 mA

■ Measuring spot size : field 2°

Product Specification Note (1) Definition of Vsat and Vth (at 20℃) Note (2) Definition of Viewing Angle : Note (3) Definition of Contrast Ratio(CR) : measured at the center point of panel Luminance with all pixels white CR = Luminance with all pixels black Note (4) Definition of Response Time : Sum of TR and TF

Product Specification Note (5) Definition of optical measurement setup Note (6) Definition of brightness uniformity Note (7) Rubbing Direction (The different Rubbing Direction will cause the different optima view direction.

Product Specification Module No.: YX21520376811FA-LP8 Note 1 : 11: White- hi lack-Red-Green- Hlue Pattern Aging, LiHEack pattern, when no LVOS signal

5.1 LADS Interface {T\; TTIC63LVDF83A or Equivalent) 5,2,1 LVDS Interlace

Product Specification

LT^LJl m-ul hj G7 - GO Invalid Data | x j MEM

Product Specification

Product Specification Module No.: YX21520376811FA-LP8

Product Specification (m Module No.: YX21520376811FA-LP8 the low or keep high impedance. 2. Do not keep the interlace signal high impedance when power is on. 3. Back Light must be turn on after power for logic and interlace signal are valid. 4. T7 decreases smoothly, there is none re-bouncing voltage. 5. The above power sequence should be satisfied at these case -.DC power On/Oft; AC power On -.Mode Change ( Resolution, frequency, timing, sleep mode, color depth change etc.) If not to follow power sequence, there is a risk of abnonnal display.

Product Specification FIGURE 5 (located in Appendix) shows mechanical outlines for the model MV215FIIB-N31 Other parameters are shown in Table 8. <Table 8. Dimensional Parameters>

测试取点 请如上图 深 圳 市 宇 锡 科 技 有 限 公 司 SHENZHEN YOUSEE TECHNO

This product is not authorized for use in life supporting systems, aircraft navigation control systems, military systems and any other application where performance failure could be life-threatening or otherwise catastrophic. 10.2.1 Please use the mounting hole on the module side in installing and do not bending or wrenching LCD in assembling. And please do not drop, bend or twist LCD module in handling. 10.2.2 Please design display housing in accordance with the following guide lines. 10.2.2.1 Housing case must be destined carefully so as not to put stresses on LCD all sides and not to wrench...

Product Specification 7.5 Absolute Maximum Ratings and Power Protection Circuit 10.5.1 Do not exceed the absolute maximum rating values, such as the supply voltage variation, input voltage variation, variation in parts’ parameters, environmental temperature, etc., otherwise LCD module may be damaged. 10.5.2 Please do not leave LCD module in the environment of high humidity and high temperature for a long time. 10.5.3 It’s recommended employing protection circuit for power supply. 10.6.1 Do not touch, push or rub the polarizer with anything harder than HB pencil lead.Use fingerstalls of soft gloves...