深圳市宇锡科技有限公司 SHENZHEN YOUSEE TECHNOLOG CO., LTD DISPLAY SPECIFICATION Product NO: (产品型号) Customer : (客 户) APPROVED BY CUSTOMER 客户签署栏 Approved by Remark 审核 备注 APPROVED BY YOUSEE 宇锡签署栏 Checked by 检查 电 子 结 构 深圳市宇锡科技有限公司 Shenzhen Yousee Technology Co.,Ltd 邹长城 LONG Tel:15818552076 E-mail: [email protected] Adress:深

Shenzhen Yousee Technology Co., Ltd Product Specification 1.GENERAL INFORMATION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4 基本描述 2 .MODULE OUTLINE DRAWIN - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -5 产品外形图 3.INTERFACE DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -6 接口定义 4.ABSOLUTE MAXIMUM RATINGS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -7 极限参数 (IC) 5.ELECTRICAL CHARACTERISTICS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -7 模块电气特性 6.BACKLIGHT CHARACTERISTICS...

Shenzhen Yousee Technology Co., Ltd Product Specification 1. GENERAL INFORMATION 基本描述 Contents 内容 a-si TFT，Positive Transmissive type Number of Dots 点阵 Outline dimensions 外形尺寸 Active area 有效区域 Pixel pitch 像素 Module size 模组尺寸 Viewing direction 视角方向 Backlight type 背光类型 LCD Driver IC LCD 驱动 IC Interface type 接口类型 LCM Input voltage 模组输入电压 Version: First Edition

设计注意事项： 1.图中FRAME VA为推荐TP视窗位置 、大小，建议TP视窗位置、大小不 要超过FRAME VA。 2.整机机壳带泡棉产品，建议客户 机壳泡棉进入LCD单边0.5MM MIN, 防止漏光。 3.整机机壳不带泡棉产品，建议客 户整机TP的丝印黑油开窗或者LENS 丝印黑油开窗比LCD A.A区单边大 0.6MM MAX。 4.客户需保证触摸屏下表面到玻璃 上表面最少0.3MM MIN(非贴合)。

Shenzhen Yousee Technology Co., Ltd Product Specification 3. INTERFACE DESCRIPTION 接口定义 Chip Selected (“Low” is enable) Serial interface Clock input Serial data input/output PIN Reset Signal pin (“Low” is enable) System ground Version: First Edition Data or command select pin. “H”: Date, “L”

Shenzhen Yousee Technology Co., Ltd Product Specification 4. ABSOLUTE MAXIMUM RATINGS 极限参数(IC) Parameter 参数 Operating temperature 操作温度 Storage temperature 存储温度 Supply voltage for logic 逻辑电压 I/O Input voltage for analog circuit 输入模拟电压 5. ELECTRICAL CHARACTERISTICS 模块电气特性 Parameter Analog operating voltage 模拟电压 Logic operating voltage 逻辑电压 Input voltage “H”level 输入高电平 Input voltage “L”level 输入低电平 Output voltage “H”level 输出高电平

Shenzhen Yousee Technology Co., Ltd Product Specification Forward voltage 正向电压 Connection mode 连接类型 7. OPTICAL CHAYACTERISTICS 光学特性 Item Response time 响应时间 Contrast ratio Color gamut Chromaticity 色度坐标 Note1.Response time is the time required for the display to transition from White to black(Rise Time,Tr)and from black to white(Decay Time,Tf).For additional information see FIG1... 备注 1.响

Shenzhen Yousee Technology Co., Ltd Product Specification Note2.contrast Ratio(CR) is defined mathematically by the following formula ,For more information see FIG2. Contrast Ratio(CR)=Average Surface Luminance with all white pixels/ Average Surface Luminance with all black pixels 备注 2.对比度是由以下公式计算所得。详见 FIG2. 对比度=显示白色画面时平均表面亮度（P1，P2,……)/显示黑色画面时平均表面亮度（P1，P2,……) FIG2. Measuring method for Contrast ratio,surface luminance,Luminance uniformity,CIE(X,Y) chromaticity. 对比度，表面亮度，均匀度，CIE 坐标测试方法 Note4.Viewing angle is the angel at which contrast ratio is greater than a specific value.For TET module,the...

Shenzhen Yousee Technology Co., Ltd Product Specification 角来定义，详见 FIG3.。 FIG3 The definition of viewing angle 视角定义 Note6.CIE(X,Y)chromaticity is the Center point value.For more information see FIG2. 备注 6.选择中心点，分别测试 X，Y 值，详见 FIG2.。 Note7.For Viewing angle and response time testing,the testing date is base on AutronicMelchers's ConScope.Series instruments.For contrast ratio,Surface Luminance,Luminance uniformity and CIE,the testing date is base on CS-2000(BM-7/CA310) photo detector. 备注 7.视角和响应时间，测试数据基于 Autronil Melchers's Conoscope 系列测试仪器，而对比度，表 面亮度，均匀度 CIE 坐标，测试数据基于 CS-2000(BM-7/CA310)光学测试仪 。...

8.2 Power on/off sequence with 3- power P/N: YX20008A Version: First Edition YX-RD-001-A Page 10 of 19

Shenzhen Yousee Technology Co., Ltd Product Specification NOTE: This section is only for reference,Details please refer to the IC specification. 9. RESET INPUT TIMING Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification Table 47: Reset Timing 3. During the Resetting period, the display will be blanked (The display enters (he blanking sequence, which maximum time is 12Q ms, when Reset Starts in the Sleep Out mode. The display remains the blank state in the Sleep In mode.) and then return to Default condition for Hardware Reset. 4. Spike Rejection can also be applied during a valid reset pulse, as shown below: NOTE: This section is only for reference,Details please refer to the IC specification. 10. Production process control WORKFLOW CHART P/N: YX20008A...

Shenzhen Yousee Technology Co., Ltd Responsibility accounting 权责单位 Flow Chart 流程图 Production design 生产计划排程 Production arrangements 生产准备 First article production 首件生产 First article assurance 首件确认 Process Inspection Product Material Control 生产计划与 物料控制 Production department 生产部 Production department 生产部 Quality department 品 质部 Production department or Quality department 生产部/品质 部 Quality department 品 质部 Production department 生 产部 Production department or Quality department 生产部/品 质部 Production department or storage 生产部/仓库 Product Specification Related Files Form used 《Production planning and control...

Shenzhen Yousee Technology Co., Ltd Product Specification rrrTOTO rrr^ ^rr rrrTOTO lcd r®® (^rr) rr x &r y Version: First Edition

Shenzhen Yousee Technology Co., LtdProduct Specification Y>0.8 Note;The rest of the test items according to our standards12. RELIABILITY TEST CONDITIONS NO. P/N: YX20008A Version: First Edition YX-RD-001-A Page 15 of 19

Shenzhen Yousee Technology Co., Ltd Product Specification Temperature Cycle Damp Proof Test 防潮测试 higher than initial value. 电流 IDD 大于初始值的 两倍。 测试前对样品进行外观和功能测试， 采用空气放电，对 TP 进行单次放 电，9 个点每一点放电一次，每次间 检查，如果合格就进行下一循环测 试，如果不合格，试验停止，并进行 问题判定 13. PRECAUTIONS FOR USING LCD MODULES 模组使用注意事项 1. Handing precautions 使用注意事项 1.1 The display panel is made of glass and polarizer.As glass is fragile.It tends to become or chipped during handing especially on the edges.Please avoid dropping or jarring.Do not subject it to a mechanical shock by dropping it or impact. 显示屏由玻璃和偏光片组成，由于玻璃是脆的，使用过程中要特别注意边缘区，请防止跌落或震 动，不能机械碰撞。...