␡ൣᐲᆷ䭑、ᢰᴹ䲀‫ޜ‬ਨ SHENZHEN YOUSEE TECHNOLOG CO., LTD DISPLAY SPECIFICATION Product NO: (ӗ૱රਧ)YX2010 Customer : (ᇒ ᡧ) APPROVED BY CUSTOMER ᇘᡭㆴ㖨ṅ Approved by Remark ᇗṮ ༽⌞ APPROVED BY YOUSEE ᆽ䭗ㆴ㖨ṅ Checked by Ỷḛ ⭥ ᆀ 㔃 ᶴ ␡ൣᐲᆷ䭑、ᢰᴹ䲀‫ޜ‬ਨ Shenzhen Yousee Technology Co.,Ltd 䛩䮯෾ LONG Tel:15818552076 E-mail: zouchangcheng@youseelcd

Shenzhen Yousee Technology Co., Ltd Product Specification Record of Revision Version Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification Version: First Edition YX-RD-001-A 3/30

Shenzhen Yousee Technology Co., Ltd Product Specification P/N: YX2010 Version: First Edition

Product Specification Shenzhen Yousee Technology Co., Ltd1. GENERAL DESCRIPTION 1.1 OVERVIEW YX156OMN237-M870lis a 15.6inch FHD TFT Liquid Crystal Display opencell without LED Backlight unit and 30 pins eDP interface. This module supports 1920^1080 FHD mode and can display 16.7M colors. Note (1) The specified power consumption (with converter efficiency) is under the conditions at VCCS =3.3 V, fV = 60 Hz, LED_VCCS = 12V(Typ), fPWM = 200 Hz, Duty=100% and Ta = 25 ± 2 °C, whereas mosaic patternis displayed. Note(2)Contrast Ratio is in CSOT BLU and after CSOT AutoVcom. Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification Please refer Appendix Outline Drawing for detail design. Connector Part No.: 300E30-1010RC-G3(Starconn) 3. ABSOLUTE MAXIMUM RATINGS 3.1 ABSOLUTE RATINGS OF ENVIRONMENT Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification Temperature (°C) (b) Wet-bulb temperature should be 39 °C Max. (Ta > 40 °C). Note (2) The temperature of panel surface should be 0 °C min. and 60 °C max. 3.2 ELECTRICAL ABSOLUTE RATINGS 3.2.1 TFT LCD MODULE Note (1) Stresses beyond those listed in above “ELECTRICAL ABSOLUTE RATINGS” may cause permanent damage to the device. Normal operation should be restricted to the conditions described in “ELECTRICAL CHARACTERISTICS”. Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification FUNCTION BLOCK DIAGRAM INPUT CONNECTOR DC/DC CONVERTER BACKLIGHT UNIT Input Signals INTERFACE CONNECTIONS No Connection ˈPlease let it open High Speed Ground True Signal-Main Lane 1 High Speed Ground True Signal-Main Lane 0 High Speed Ground True Signal-Auxiliary Channel Complement Signal-Auxiliary Channel High Speed Ground Power Supply +3.3V (typical) Power Supply +3.3V (typical) P/N: YX2010 Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 14 N ote (1) The pixel is shown in the following figure.

Shenzhen Yousee Technology Co., Ltd Product Specification 4.3 ELECTRICAL CHARACTERISTICS4.4 LCD ELETRONICS SPECIFICATION Parameter Note (1) The ambient temperature is Ta = 25 ± 2 °C. Note (2) Irush: the maximum current when VCCS is rising Iis: the maximum current of the first 100ms after power-on Measurement Conditions: Shown as the following figure. Test pattern: Mosaic Note (3) The specified power supply current is under the conditions at VCCS = 3.3 V, Ta = 25 ± 2 °C, DC Current and fv = 60 Hz, whereas a power dissipation check pattern below is displayed. Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification LED CONVERTER SPECIFICATION Note (1) ILEDRUSH: the maximum current when LED_VCCS is rising, ILEDIS: the maximum current of the first 100ms after power-on, Measurement Conditions: Shown as the following figure. LED_VCCS = Typ, Ta = 25 ± 2 °C, fPWM = 200 Hz, VLED rising time is 0.5ms Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification Note (2) PL = IL xVl (With LED converter transfer efficiency); Note (3) The specified LED power supply current is under the conditions at “LED_VCCS = Typ.”, Ta = 25 ± 2 °C, fPWM = 200 Hz, Duty=100%. Note (1) LED current is measured by utilizing a high frequency current meter : Note (2) For better LED light bar driving quality, it is recommended to utilize the adaptive boost converter with current balancing function to drive LED light-bar. Note(3):Recommended B/L :6S9P4.5 INPUT SIGNAL TIMING SPECIFICATIONS4.5.1 eDP AUX Channel Characteristics...

Shenzhen Yousee Technology Co., Ltd Product Specification Peak-to-peak voltage at TP1 4.5.2 eDP Main Link Receiver Characteristics Parameter 4.5.3 eDP AUX Channel Characteristics Parameter Single Ended Version: First Edition YX-RD-001-A 13/30

Shenzhen Yousee Technology Co., Ltd Product Specification 4.5.4 COLOR DATA INPUT ASSIGNMENT The brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input for the color. The higher the binary input the brighter the color. The table below provides the assignment of color versus data input. Data Signal Basic Blue Colors Cyan P/N: YX2010 Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 4.6 DISPLAY TIMING SPECIFICATIONSThe input signal timing specification is showed as the following table and timing diagram. Signal Version: First Edition YX-RD-001-A 15/30

Shenzhen Yousee Technology Co., Ltd Product Specification Note (1) Display timing signal should be contained and transferred by Display Port Main Link stream data packing described in VESA Display Port Standard V1.4b. INPUT SIGNAL TIMING DIAGRAM P/N: YX2010 Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 4.7 POWER ON/OFF SEQUENCE Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification t11 Note (1) Please follow the power on/off sequence described above. Otherwise, the LCD module might abnormal display or be damaged. Note (2) Please avoid floating state of interface signal at invalid period. Whenthe interface signal is invalid,be sureto pull down the power supply of LCD VCCS to 0 V Note (3) The backlight must be turned on after the power supply for the logic and the interface signal is valid. The backlight must be turned off before the power supply for the logic and the interface signal is invalid. Note (4) Please follow...