␡ൣᐲᆷ䭑、ᢰᴹ䲀‫ޜ‬ਨ SHENZHEN YOUSEE TECHNOLOG< CO., LTD DISPLAY SPECIFICATION Product NO: (ӗ૱රਧ) Customer : (ᇒ ᡧ) APPROVED BY CUSTOMER ᇘᡭㆴ㖨ṅ Approved by Remark ᇗṮ ༽⌞ APPROVED BY YOUSEE ᆽ䭗ㆴ㖨ṅ Checked by Ỷḛ ⭥ ᆀ 㔃 ᶴ ␡ൣᐲᆷ䭑、ᢰᴹ䲀‫ޜ‬ਨ Shenzhen Yousee Technology Co.,Ltd 䛩䮯෾LONG Tel:15818552076 E-mail: zouchangcheng@youseeOF

Shenzhen Yousee Technology Co., Ltd Product Specification Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification YX133B56-111-1901 is a color active matrix TFT LCD module using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This module has a 13.3 inch diagonally measured active area with Full-HD resolutions (1920 horizontal by 1080 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and this module can display 16.7 M colors. Figure 1. Drive Architecture • 2 lane eDP interface with 2.7Gbps link rates • Thin and light weight • 16.7M color depth, color gamut 72%...

Shenzhen Yousee Technology Co., Ltd Product Specification < Table 1. General Specifications > Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 2.0 ABSOLUTE MAXIMUM RATINGS The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and non-operational maximum voltage and current values are listed in Table 2. < Table 2. Environment Absolute Maximum Ratings> 1. These range above is maximum value not the actual operating temperature . Actual Operating temperature is no more than 50°C and temperature refers to the LCM surface temperature ; 2. BOE is not responsible for product problems beyond the use conditions. 3. When the...

Shenzhen Yousee Technology Co., Ltd Product Specification 3.0 ELECTRICAL SPECIFICATIONS 3.1 TFT LCD Module < Table3. LCD Module Electrical Specifications > [Ta =25 2 °C] Notes : 1. The supply voltage is measured and specified at the interface connector of LCM. The current draw and power consumption specified is for 3.3V at 25 °C Max value at Black Pattern 2. Calculated value for reference ILEDx VLED/0.85 = PLED Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification < Table 4. LED Driving guideline specifications > Ta=25+/-2°C Notes : 1. Calculator Value for reference Iled ^ VLED “ PLED 2. The LED Life-time define as the estimated time to 50% degradation of initial luminous under the condition of the ambient temperature of 25°C. Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 4.0 INTERFACE CONNECTION.4.0.1 Electrical Interface Connection The electronics interface connector is IS050-L30B-C10. The connector interface pin assignments are listed in Table 5 and 6. <Table 5. Pin Assignments for the Interface Connector> Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 4.2 Data Input Format Figure 2. Pixel Format Display Position of Input Data (V-H) Figure 3. Scan direction Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 5.0 SIGNAL TIMING SPECIFICATION5.0.1 The QV133FHB-N81 is operated by the DE only. Item Note: The DCLK range at last line of V-blanking should be set in 0-H-active/2. Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 6.0 POWER SEQUENCETo prevent a latch-up or DC operation of the LCD module, the power on/off sequence shall be as shown in below < T1 1. When the power supply VDD is 0V, keep the level of input signals on the low or keep high impedance. 2. Do not keep the interface signal high impedance when power is on. Back Light must be turn on after power for logic and interface signal are valid. Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 7.0 OPTICAL SPECIFICATION 7.0.1 Overview The test of view angle range shall be measured in a dark room (ambient luminance < 1lux and temperature = 25±2°C) with the equipment of Luminance meter system (Goniometer system and TOPCON CS2000/CA310) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of 0 and O equal to 0°. We refer to 00=0 (=03 ) as the 3 o’clock direction (the "right”), 0 0=90 (= 012 ) as the 12 o’clock direction ("upward”), 0 0=180 (= 09 ) as the 9 o’clock direction ("left”)...

Shenzhen Yousee Technology Co., Ltd Product Specification Notes : 1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing angles are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock direction with respect to the optical axis which is normal to the LCD surface (see FIGURE 1). 2. Contrast measurements shall be made at viewing angle of = 0 and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state . (see FIGURE 1) Luminance Contrast...

Shenzhen Yousee Technology Co., Ltd Product Specification 8.0 MECHANICAL OUTLINE DIMENSION ␡ൣᐲᆷ䭑、ᢰᴹ䲀‫ޜ‬ਨ SHENZHEN YOUSEE TECHNOLOGY CO.,

Shenzhen Yousee Technology Co., Ltd Product Specification 9.0 RELIABILITY TESTThe Reliability test items and its conditions are shown in below.<Table 8. Reliability test> No 1. The fixture must be hard enough , so that the module would not be twisted or bent. 2. Self- recovery and restart recovery is allowed. No hardware failures. Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 10.0 Precautions Please pay attention to the followings when you use this TFT LCD Panel. • (1) Use fingerstalls with soft gloves in order to keep display clean during the incoming inspection and assembly process. • (2) You must mount a module using specified mounting holes (Details refer to the drawings). • (3) Please make sure to avoid external forces applied to the Source PCB or FPC and D-IC during the process of handling or assembling. If not, It causes panel damage or malfunction. • (4) Note that polarizers are very fragile and could...