深圳市宇锡科技有限公司 SHENZHEN YOUSEE TECHNOLOG CO., LTD DISPLAY SPECIFICATION Product NO: (产品型号) Customer : (客 户) APPROVED BY CUSTOMER 客户签署栏 Approved by Remark 审核 备注 APPROVED BY YOUSEE 宇锡签署栏 Checked by 检查 电 子 结 构 深圳市宇锡科技有限公司 Shenzhen Yousee Technology Co.,Ltd 邹长城 LONG Tel:15818552076 E-mail: [email protected] Adress:深

Product Specification Shenzhen Yousee Technology Co., Ltd Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification Document Revision History Change No. Version: First Edition

Product Specification Shenzhen Yousee Technology Co., Ltd YX10123632781NC Display mode is a color active matrix thin film transistor (TFT) liquid crystal display (LCD) that uses amorphous silicon TFT as a switching device. This model is composed of a TFT LCD panel and a driving circuit.This TFT LCD has a 10.1(16:10) inch diagonally measured active display area with (800 horizontal by 1280 vertical pixel) resolution. 10.1 inch configuration Compatible with NTSC & PAL system Image Reversion: UP/DOWN and LEFT/RIGHT ROHS design Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 2.0 Optical Characteristics The optical characteristics are measured under stable conditions at 25TC (Room Temperature) : Note 1: Measurement method The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting . Backlight for 30 minutes in a stable, windless and dark room, and it should be measured in the center of screen. Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification of Average Luminance of White (YL): Measure the luminance of gray level 63 at 5 points，YL= [L (1)+ L (2)+ L (3)+ L (4)+ L (5)] / 5 L (x) is corresponding to the luminance of the point X at Figure in Note (1) Note 3：Definition of contrast ratio: Contrast ratio is calculated with the following formula. Note 4：Definition of Cross Talk (CT) CT = | YB – YA | / YA × 100 (%) Where YA = Luminance of measured location without gray level 0 pattern (cd/m2) YB = Luminance of measured location with gray level 0 pattern (cd/m2) Version: First Edition...

Shenzhen Yousee Technology Co., Ltd Product Specification Note 5: Definition of response time: The output signals of BM-7 or equivalent are measured when the input signals are changed from “Black” to “White” (falling time) and from “White” to “Black” (rising time), respectively. The response time interval between the 10% and 90% of amplitudes. Refer to figure as below. Note 6. Definition of viewing angle Viewing angle is the measurement of contrast ratio ≧10, at the screen center, over a 180° horizontal and 180° vertical range (off-normal viewing angles). The 180° viewing angle range is broken...

Product Specification Shenzhen Yousee Technology Co., Ltd 3.2.1 Electrical Absolute Rating Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 3.3 power on/off sequence Power on: IOVCC, VCCH Power Status Initial setting Video Packet SLPIN Mode SLPOUT Mode Version: First Edition

Shenzhen Yousee Technology Co., Ltd Version: First Edition Product Specification

Shenzhen Yousee Technology Co., Ltd Product Specification 3.4 MIPI Interface(Mobile Industry Processing Interface) The Display Serial Interface (DSI) specifies the interface between a host processor and a peripheral. DSI builds on existing MIPI Alliance specifications by adopting pixel formats and command set specified in DPI-2, DBI-2 and DCS standards. 3.4.1 MIPI Signal Timing Characteristics 3.4.1.1 AC Electrical Characteristics High-Speed Data-Clock Timing This section specifies the required timings on the high-speed signaling interface independent of the electrical characteristics of the...

Shenzhen Yousee Technology Co., Ltd Product Specification The same clock source is used to generate the DDR Clock and launch the serial data. Since the Clock and Data signals propagate together over a channel of specified skew, the Clock may be used directly to sample the Data lines in the receiver. Such a system can accommodate large instantaneous variations in UI. The allowed instantaneous UI variation can cause large, instantaneous data rate variations. Therefore, devices shall either accommodate these instantaneous variations with appropriate FIFO logic outside of the PHY or provide an accurate...

Shenzhen Yousee Technology Co., Ltd Product Specification Data-Clock Timing Specifications The Data-Clock timing specifications are shown in Table 13.12. Implementers shall specify a value UIinst.min that represents the minimum instantaneous Ul possible within a High-Speed data transfer for a given implementation. Parameters in Table 13.12 are specified as a part of this value.. The setup and hold times, TSetup[rx] and THold[rx], respectively, describe the timing relationships between the data and clock signals. TSetup[rx] is the minimum time that data shall be present before a rising or falling...

Shenzhen Yousee Technology Co., Ltd Product Specification Burst Mode Data Transmission CLK Figure 11.7: High-Speed Data Transmission in Bursts Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification Figure 11.8: Switching the Clock Lane between Clock Transmission and Low-Power Mode Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification Note: (1) The VS and VBP pulse width are related to GIP start pulse and GIP clock pulse timing. The GIP start pulse and GIP clock pulse must be set at corresponding position for LCD normal display. Following figure shows the relationship of the input signals and LCD pixel format. Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 5.0 Back-light Unit: PARAMETER Note (1) Permanent damage may occur to the LCD module if beyond this specification. Functional operation should be restricted to the conditions described under normal operating conditions. (3) Test condition: LED Current 180mA Version: First Edition