深圳市宇锡科技有限公司 SHENZHEN YOUSEE TECHNOLOG CO., LTD DISPLAY SPECIFICATION Product NO: (产品型号) Customer : (客 户) APPROVED BY CUSTOMER 客户签署栏 Approved by Remark 审核 备注 APPROVED BY YOUSEE 宇锡签署栏 Checked by 检查 电 子 结 构 深圳市宇锡科技有限公司 Shenzhen Yousee Technology Co.,Ltd 邹长城 LONG Tel:15818552076 E-mail: [email protected]

Shenzhen Yousee Technology Co., Ltd Product Specification CONTENT LIST Cover ----------------------------------------------------------------------------------------------1

Shenzhen Yousee Technology Co., Ltd Product Specification

Product Specification Shenzhen Yousee Technology Co., Ltd YX025Z6M-J80 is a color active matrix TFT-LCD Panel using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This model is composed of a TFT-LCD Panel, a driving circuit and a back light system. It is a transmissive type display operating in the normal black. This TFT-LCD has a 2.47 inch diagonally measured active area with Z6 resolutions (480 horizontal by 480 vertical pixel array). Each pixel is divided into Red, Green, Blue dots which are arranged in 2 domain stripe and this panel can display 16.7M colors....

Shenzhen Yousee Technology Co., Ltd Product Specification 1.4 General Specifications (H: horizontal length, V: vertical length) 1. At the U/D/L/R direction, the viewing angle is same;

Shenzhen Yousee Technology Co., Ltd Product Specification 2.0 ABSOLUTE MAXIMUM RATINGS The absolute maximum ratings are list on table as follows. When used out of the absolute maximum ratings, the LSI may be permanently damaged. Using the LSI within the following electrical characteristics limit is strongly recommended for normal operation. If these electrical characteristic conditions are exceeded during normal operation, the LSI will malfunction and cause poor reliability. If the absolute maximum rating of even is one of the above parameters is exceeded even momentarily, the quality of the...

Shenzhen Yousee Technology Co., Ltd Product Specification 3.0 ELECTRICAL SPECIFICATIONS 3.1 TFT LCD Module DC Characteristics 2. Quantity of LED: 2line x 3LEDs per line = 6 LEDs

Shenzhen Yousee Technology Co., Ltd Product Specification 3.3 Block Diagram GO AY control signal Bonding area

Shenzhen Yousee Technology Co., Ltd Product Specification

Shenzhen Yousee Technology Co., Ltd Product Specification 4.2 MIPI Characteristics MODE

Shenzhen Yousee Technology Co., Ltd Product Specification 5.0 SIGNAL TIMING SPECIFICATION5.1 Vertical timings DSI Packets (PCLK depend on DSI clock and data lanes)

Shenzhen Yousee Technology Co., Ltd Product Specification 6.0 POWER ON/OFF SEQUENCE6.1 Power on sequence Eytemal VDD1 / VC03 Cn Initial code / Before/Same with RESX HostCMD Video Packet m Note : MIPI Data/ CLK lane should be LP-11 state before RESX rising edge Initial SLPOUT DISPOM

Shenzhen Yousee Technology Co., Ltd Product Specification 7.0 OPTICAL SPECIFICATIONS 7.1 Overview The test of Optical specifications shall be measured in a dark room(ambient luminance< 1 lux and temperature = 25±2C) with the equipment of Luminance meter system (Topcon SR-UL1R and Westar TRD-100A) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of 0 and O equal to 0°.The center of the measuring spot on the Display surface shall stay fixed. The backlight should be operating for 30 minutes prior to measurement. 1. Viewing angle is the angle...

Shenzhen Yousee Technology Co., Ltd Product Specification 4. Uniformity measurement shall be taken at the locations shown in FIG. 1&2, for a total of the measurements per display, measure surface luminance of these nine points across the LCD surface 50cm from the surface with all pixels displaying white. Uniformity Min Luminance of 13 points Max Luminance of 13 points 5. The color chromaticity coordinates specified in Table1 shall be calculated from The spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the Module. 6. The electro-optical...

Shenzhen Yousee Technology Co., Ltd Product Specification Figure 3. Response Time Testing

Shenzhen Yousee Technology Co., Ltd Product Specification 8.0 MECHANICAL CHARACTERISTICS 8.1 Dimension Requirements for MDL Part Mechanical outlines for the panel (H: horizontal length, V: Vertical length) Parameter Panel size Active area Number of pixels Dimensional outline Display mode Normally Black Figure 5. LCM Outline Dimension (unit: mm)

Shenzhen Yousee Technology Co., Ltd Product Specification Figure 6. BLU Outline Dimension (unit: mm)

Shenzhen Yousee Technology Co., Ltd Product Specification

Shenzhen Yousee Technology Co., Ltd Product Specification 10.0 PACKING METHOD 10.1 Packing Tray L: 360mm; W: 260mm; H:80mm. (6ea Tray Product + 1ea Empty Tray)

Shenzhen Yousee Technology Co., Ltd Product Specification

Shenzhen Yousee Technology Co., Ltd Product Specification • Panel should be placed upwardly while in the tray. • Every six full trays with a blank one while twining twice on both sides by adhesive tape. • Every tray should be put crossly. • Panels should be packed in a vacuum with PE (anti-ESD) bag.

Shenzhen Yousee Technology Co., Ltd Product Specification Application area> (/) <Mode>

Shenzhen Yousee Technology Co., Ltd Product Specification 12.0 HANDDLING & CAUTIONS12.1 Mounting Method • The panel of the LCM consists of two thin glasses with polarizer which easily get damaged. So extreme care should be taken when handling the LCM. • Excessive stress or pressure on the glass of the LCM should be avoided. Care must be taken to insure that no torsional or compressive forces are applied to the LCM unit when it is mounted. • If the customer's set presses the main parts of the LCM, the LCM may show the abnormal display. But this phenomenon does not mean the malfunction of the LCM...

Shenzhen Yousee Technology Co., Ltd Product Specification 12.3 Caution Against Static Charge • The LCM use C-MOS LSI drivers, so customers are recommended that any unused input terminal would be connected to Vdd or Vss, do not input any signals before power is turn on, and ground you body, work/assembly area, assembly equipments to protect against static electricity. • Remove the protective film slowly, keeping the removing direction approximate 30-degree not vertical from panel surface, if possible, under ESD control device like ion blower, and the humidity of working room should be kept over...