␡ൣᐲᆷ䭑、ᢰᴹ䲀‫ޜ‬ਨ SHENZHEN YOUSEE TECHNOLOG CO., LTD DISPLAY SPECIFICATION Product NO: (ӗ૱රਧ) YX)+01 Customer : (ᇒ ᡧ) APPROVED BY CUSTOMER ᇘᡭㆴ㖨ṅ Approved by Remark ᇗṮ ༽⌞ APPROVED BY YOUSEE ᆽ䭗ㆴ㖨ṅ Checked by Ỷḛ ⭥ ᆀ 㔃 ᶴ ␡ൣᐲᆷ䭑、ᢰᴹ䲀‫ޜ‬ਨ Shenzhen Yousee Technology Co.,Ltd 䛩䮯෾ LONG Tel:15818552076 E-mail: zouchangcheng@youseelcd

Shenzhen Yousee Technology Co., Ltd Product Specification Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 1.0 GENERAL DESCRIPTION 1.1 Introduction B6 ?>,.34 is a color active matrix LTPS LCD using Low Temperature Poly-sil icon TFT‘ s (Thin Film Transistors) as an active switching devices. The LTPS-LCD has a 13.92 inch diagonally measured active area with FHD resolutions (1920horizontal by 1080vertical pix el arrays). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical st ripe and this module can display 16.7M colors. 1.2 Features Border (L/R/U/D) : NTSC73% wide viewing angle (U/D/L/R)80/80/80/80 Version: First Edition...

Shenzhen Yousee Technology Co., Ltd Product Specification The followings are general specifications of YX140FHM-N10. <Table 1. General Specifications> Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 2.0 ABSOLUTE MAXIMUM RATINGS The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and non-operational maximum voltage and current values are listed in Table 2. < Table 2. Absolute Maximum Ratings> [1] Liquid Crystal driving voltage Due to the characteristics of LC Material, this voltage varies with environmental temperature. 1. These range above is maximum value not the actual operating value . Actual Operating temperature is 25°C . bulb temperature should be 39 0C max. and...

Shenzhen Yousee Technology Co., Ltd Product Specification 3.0 ELECTRICAL SPECIFICATIONS3.1Electrical Specifications< Table 3. Electrical specifications > [Ta =25 ±2 °C] 1. VGH is TFT Gate operating voltage. 2. VGL is TFT Gate operating voltage. The low voltage level of VGL signal must be fluctuates with same phase as Vcom. 3. Vcom must be adjusted to optimize display quality, as Crosstalk and Contrast Ratio etc.. 4. The value is just the reference value. The customer can optimize the setting value . Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 3.0 ELECTRICAL SPECIFICATIONS 3.2 TFT LCD Module 1. The supply voltage is measured and specified at the interface connector of FOB. 2. The current draw and power consumption specified is for VDDIN=3.3V, Frame rate=60Hz. Test Pattern of power supply current is White pattern. Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 3.3 INPUT TERMINAL PIN ASSIGNMENT The electronics interface connector is W05030-30P-H/IS050-L30B-C10 The connector interface pin assignments are listed in Table 5. Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 4.0 OPTICAL SPECIFICATION 4.1 Overview The test of Optical specifications shall be measured in a dark room (ambient luminance <1lux and temperature = 25±2°C) with the equipment of Luminance meter system (Goniometer system and TOPCON BM-5) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of 0 and $ equal to 0°. We refer to 00=0 (=03 ) as the 3 o"clock direction (the “right”), 00=90 (= 012 ) as the 12 o"clock direction (“upward”), 00=180 (= 09 ) as the 9 o"clock direction (“left”) and...

Shenzhen Yousee Technology Co., Ltd Product Specification Note : 1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing angles are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock direction with respect to the optical axis which is normal to the LCD surface (see FIGURE 4). 2. Contrast measurements shall be made at viewing angle of ©= 0 and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state . (see FIGURE 1) Luminance Contrast...

Shenzhen Yousee Technology Co., Ltd Product Specification 6.0 Mechanical Characteristics 3KINGTOIGR*XG]OTM *XG]OTM'ZZGINSKTZ ,XUTZ Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 6.0 Mechanical Characteristics 3KINGTOIGR*XG]OTM *XG]OTM'ZZGINSKTZ (GIQ Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 7.0 APPENDIX Figure 1. Optical Test Equipment Setup Figure 2. Response Time Testing Figure 3. The Definition of Vth & Vsat Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification Figure 4. Viewing Angle Range is defined as follows; θ=0o UP (12 o’clock) z yuo Φ=90 θ LEFT xl (9 o’clock) Φ=180o Figure 5. Pol General Spec Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 8.0 RELIABILITY TEST The Reliability test items and its conditions are shown in below. <Table 8. Reliability test> Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 9.0 Handling & Cautions 9.1 Mounting Method • The panel of the LCD consists of two thin glasses with polarizers which easily get damaged. So extreme care should be taken when handling the LCD. • Excessive stress or pressure on the glass of the LCD should be avoided. Care must be taken to insure that no torsional or compressive forces are applied to the LCD unit when it is mounted. • If the customer's set presses the main parts of the LCD, the LCD may show the abnormal display. But this phenomenon does not mean the malfunction of the LCD...