深圳市宇锡科技有限公司 SHENZHEN YOUSEE TECHNOLOG CO., LTD DISPLAY SPECIFICATION Product NO: (产品型号) Customer : (客 户) APPROVED BY CUSTOMER 客户签署栏 Approved by Remark 审核 备注 APPROVED BY YOUSEE 宇锡签署栏 Checked by 检查 电 子 结 构 深圳市宇锡科技有限公司 Shenzhen Yousee Technology Co.,Ltd 邹长城 LONG Tel:15818552076 E-mail: [email protected] Adress:深

Shenzhen Yousee Technology Co., Ltd Product Specification Version History

Shenzhen Yousee Technology Co., Ltd Product Specification

Shenzhen Yousee Technology Co., Ltd Product Specification 2 Features2.1 Product Applications Tablet, notebook, portable GPS, handheld game console... 2.2.1 Display color: 1.07B (RGB x 10 bits) 2.2.3 Pixel arrangement: Real RGB 2.2.4 Display Interface: MIPI 2-port D-PHY TP Interface: SPI 2.2.6 Touch screen: On-cell; Touch IC: GT6975P 2.2.7 Module type: Full module

Shenzhen Yousee Technology Co., Ltd Product Specification 4 Mechanical Specifications Item a) MT TP_AVDD, AM LDO iA^MMA(fIAA'^)A/T 250mA, OCP (MMM)A b) ^MMUKUAMfiiAT, ^MMSfiMAAAU, AAMX c) XASX: MA^MU LDO PW/XASXo tfcA TP 3.0V, U LDO PW/XASXA 0.2V,MMU LDO iA^AAt^KT 3.2V. AA^MASA,A

Shenzhen Yousee Technology Co., Ltd Product Specification 池电压可能会降，且带载能力变差，此时整机电源若不满足 LDO 的最小压差要求，可能会因压差不 足，导致 AVDD 电压不稳定，影响触控模组性能 TP_AVDD 上建议不要串磁珠或电感等，以防压降,TP_AVDD 如需要串电阻处理时，建议串接 0 欧姆。 1) Normal Mode Power Supply: VDDI=1.8V VCI=3.3V Frame Frequency: Fframe =120HZ @ 25degC, Brightness 450 nits, Command Mode, Display Condition 100% Pixel On 450nits VELVDD=4.6V VELVSS= -3.5V IELVDD /ELVSS 2) HBM Mode Power Supply: VDDI=1.8V VCI=3.3V Frame Frequency: Fframe =120HZ @ 25degC, Brightness 600 nits, Command Mode, Display Condition 100% Pixel On 600 nits VELVDD=4.6V VELVSS= -3.5V IELVDD /ELVSS 5.2 TP IC...

Shenzhen Yousee Technology Co., Ltd Product Specification Consumption( W/Driver) Sleep

Shenzhen Yousee Technology Co., Ltd Product Specification

Shenzhen Yousee Technology Co., Ltd Product Specification Note1:该接口为 MIPI D-PHY v1.1 带 VESA DSC 1.1 压缩 5.4 Graphic memory writing direction 5.5 Recommended Operating Sequence 5.5.1 Timing Specification of Power On/Off Sequence

Shenzhen Yousee Technology Co., Ltd Product Specification Timing Specification of Power On/Off Sequence

Shenzhen Yousee Technology Co., Ltd Product Specification 5.5.4 SPI 通讯 GT6975P 提供 SPI 接口，仅支持 CPOL=0、CPHA=0 模式。由 SPI_MOSI（从机数据输入）， SPI_MISO（从机数据输出），SPI_CLK（时钟），SPI_CS（片选）与主控进行通信。GT6975P 始终 作为从设备，所有通信都是由主控发起。 SPI 写操作协议 CMD(W)：写操作命令，固定为 0xF0 ADDR_0~ADDR_3：待写入的寄存器 32 位地址（大端模式：高字节在前，低字节在后） DATA_0~DATA_n：待写入的字数据 SPI 读操作协议 1.One Byte 模式

Shenzhen Yousee Technology Co., Ltd Product Specification

Shenzhen Yousee Technology Co., Ltd Product Specification

Shenzhen Yousee Technology Co., Ltd Product Specification Environmental conditions: Temp.25°C±3°C, 65±20%RH, Dark Room. Distance of OLED display center to measuring machine is 50cm. Measure 13 points of Display Brightness, Brightness Uniformity=Lmin/LMaxx100% Note3: Contrast Ratio Dark Room C.R=LW/LB LW: full white brightness of display center P0; LB : full black brightness of display center P0. Out-spec panel(4.5~5.5JNCD) should be less than 5%

Shenzhen Yousee Technology Co., Ltd Product Specification Note5: Cross-talk 4% black or white window ，127 gray background. |LWi_ON − LW_OFF | × 100%(i = 5 ݑpݑ 8) LW_OFF |LBi_ON ܢȒ LB_OFF | × 100%(i = 5 to 8) LB_OFF For black windows ABi (i = 5 to 8). The maximum cross-talk value shall be noted in the measurement report. Note6: Response Time Response time=Pixel turn on and turn off time (White<=>Black). It is measuring transition time from 10% to 90% of luminance.

Shenzhen Yousee Technology Co., Ltd Product Specification Note 7: Flicker Suggested Instruments: Konica Minolta CA-310 or Klein Instruments K-8 The flicker level is defined by Fast Fourier Transformation (FTT) as follows: Where fFFTC(n) is the n-th FFT coefficient. fFFTC(0) is the 0-th FFT coefficient which is DC component. FS(Hz) is the flicker sensitivity as a function of frequency. The peak flicker level shall be reported based on the calculation using above formula in which FS(Hz) is determined by the flicker weighing factor shown below.

Shenzhen Yousee Technology Co., Ltd Product Specification Note8 Short-burn in To measure the burn-in e⌽㎤ ect, a test pattern with full white background (area B) and a black circle (area A) is applied to the AMOLED display at 420 nits setting with ACL off. The area of the black circle should not exceed the 20% of the whole displayed area and is big enough for brightness measurement. Not aged area Checking point for luminance change After the minimum time specied below (e.g. 200 hours), a full white image is applied on the display, and the luminance in area A and B are measured at 25℃and compared...

Shenzhen Yousee Technology Co., Ltd Product Specification at same time start to use CA310 (or similar optical device) measures the luminance of A and B(LA' / LB'), measure 60 times and each interval step is 1 sec; Calculate the JND as below method:JND=|(LB'-LA')/(LB'+LA')-(LB-LA)/(LB+LA)| / 0.004,Record the time which satisfy the JND value less than 1;

Shenzhen Yousee Technology Co., Ltd Product Specification 7.2 Touch Sensor Specification No

Shenzhen Yousee Technology Co., Ltd Product Specification TP works well under below condition: -20C to 50/10min. Check TP performance at -10C/25C/50C. TP should work well. ^7mm slug ,1mm distance to TP surface. No touch report . When 20cm palm on TP surface, no touch report and the reset area of TP still work well Execute Function Reset after power on and rouse the Pad.

Shenzhen Yousee Technology Co., Ltd Product Specification

Shenzhen Yousee Technology Co., Ltd Product Specification

Shenzhen Yousee Technology Co., Ltd Product Specification Cover lens

Shenzhen Yousee Technology Co., Ltd Product Specification 9 Outline Dimension Drawing 10 Packing Specification TBD The control of hazardous substances meet RoHS and REACH requirements.