␡ൣᐲᆷ䭑、ᢰᴹ䲀‫ޜ‬ਨ SHENZHEN YOUSEE TECHNOLOG< CO., LTD DISPLAY SPECIFICATION Product NO: (ӗ૱රਧ) Customer : (ᇒ ᡧ) APPROVED BY CUSTOMER ᇘᡭㆴ㖨ṅ Approved by Remark ᇗṮ ༽⌞ APPROVED BY YOUSEE ᆽ䭗ㆴ㖨ṅ Checked by Ỷḛ ⭥ ᆀ 㔃 ᶴ ␡ൣᐲᆷ䭑、ᢰᴹ䲀‫ޜ‬ਨ Shenzhen Yousee Technology Co.,Ltd 䛩䮯෾LONG Tel:15818552076 E-mail: zouchangcheng@youseeOF

Shenzhen Yousee Technology Co., Ltd Product Specification Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 1 General Specifications Feature Note 1: Requirements on Environmental Protection: RoHS. Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 2 Input/output Terminals 2.1 Main FPC Pin Assignment FPC connector: FH26-39S-0.3SHW. Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification Note: l=lnput; 0=0utput; P=Power; l/0=lnput / Output Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 2.2 Circuit block diagram (Display) 2.3 MCU and Display Module Interface Configuration ELVDD Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 3 Absolute Maximum Ratings3.1 Driving AMOLED PanelMaximum Ratings (Voltage Referenced to VSS) Vss=0V, Ta=25°C Item Note: Functional operation should satisfy the limits in the Electrical Characteristics tables or Pin Description section. If the module exceeds the absolute maximum ratings, permanent damage may occur. Besides, if the module is operated with the absolute maximum ratings for a long time, the reliability may also drop. 4.1 Driving AMOLED Panel_Ta=25°CNotel: The input digital voltage is the I/O reference voltage.Note2: VDDIO...

Shenzhen Yousee Technology Co., Ltd Product Specification Note4: 60Hz command mode at 800 Mbps. P/N: YX601106 Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 5 AC Characteristics5.1 MIPI Interface Characteristics HS Data Transmission Burst P/N: YX601106 Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification Bus turnaround (BAT) from MPU to display module timing Timing Parameters: Parameter Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification Note 2. During the resetting period, the display will be blank (The display is entering blankingsequence, Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification whose maximum time is 120 ms, when Reset Starts in Sleep Out-mode. The display remains blank in Sleep In -mode) and then return to Default condition for H/W reset. Note 3. During Reset Complete Time, data in OTP will be latched to internal register during this period. This loading is done every time when there is H/W reset complete time (tREST) within 5ms after a rising edge ofRESX. Note 4. Spike Rejection also applies during a valid reset pulse as shown below: 5.3 TE Timing CharacteristicsModel, The Tearing Effect Output line consists...

Shenzhen Yousee Technology Co., Ltd Product Specification 6 Recommended Operating Sequence 6.1 Display Power on / off Sequence Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification Use “command 5100h, data xxh” to adjust the Manual Brightness value of the display: In principle relationship is that 00h value means the lowest brightness and FFh value means the highest brightness. Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 7 Optical Characteristics Optical Specification Item Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification Test Conditions: 1. The test systems refer to Notel and Note2. Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification Note 1: Definition of optical measurement system. The optical characteristics should be measured in dark room. The optical properties are measured at the center point of the AMOLED screen. All input terminals AMOLED panel must be ground when measuring the center area of the panel. Note 2: Definition of viewing angle range and measurement system. Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification Note 3: Definition of contrast ratio Lumin ance measured when LCD is on the "white" state Contrastratio(CR) = - Lumin ance measured when LCDis on the "Black" state “White state A state where the AMOLED should be driven by Vwhite. “Black state”: A state where the AMOLED should be driven by Vblack. Note 4: Definition of response time The response time is defined as the AMOLED optical switching time interval between “White” state and “Black” state. Rise time (Ton) is the time between photo detector output intensity changing from 10% to 90%....

Shenzhen Yousee Technology Co., Ltd Product Specification Note 6: Definition of luminance uniformity Active area is divided into 9 measuring areas (Refer Fig. 2). Every measuring point is placed at the center of each measuring area. Luminance Uniformity(U) = Lmin/ Lmax L-------Active area length W—~ Active area width Lmax: The measured maximum luminance of all measurement position. Lmin: The measured minimum luminance of all measurement position. Note 7: Definition of luminance: Measure the luminance of white state at the center point. Note 8: Cross Talk A. Measure luminance at the position,...

Shenzhen Yousee Technology Co., Ltd Product Specification (a) Lw_off, Lb_off measuring pattern Version: First Edition

Shenzhen Yousee Technology Co., Ltd Product Specification 8 Environmental / Reliability Test No Test Item High Temperature Operation According to the customer request According to the customer request High Temperature Storage According to the customer request According to the customer request High Temperature & High Humidity Operation According to the customer request High Temperature & High Humidity Storage According to the customer request Thermal Shock (Non-operation) According to the customer request Electro Static Version: First Edition