深圳市宇锡科技有限公司 SHENZHEN YOUSEE TECHNOLOG CO., LTD DISPLAY SPECIFICATION Product NO: (产品型号) Customer : (客 户) APPROVED BY CUSTOMER 客户签署栏 Approved by Remark 审核 备注 APPROVED BY YOUSEE 宇锡签署栏 Checked by 检查 电 子 结 构 深圳市宇锡科技有限公司 Shenzhen Yousee Technology Co.,Ltd 邹长城 LONG Tel:15818552076 E-mail: [email protected] Adress:深

Shenzhen Yousee Technology Co., Ltd Product Specification Reversion History

Shenzhen Yousee Technology Co., Ltd Product Specification

Shenzhen Yousee Technology Co., Ltd Product Specification 1 Scope This Specification defines AMOLED manufactured by Shenzhen Yousee Technology Co., Ltd., from here on refer as Yousee. In the case of any unspecified item, it may require both Yousee and the party designs this module into its product to work out a solution. Consumer Electronics 3) Pixel arrangement: Sub Pixel Rendering 4) Interface: MIPI 4 lanes

Shenzhen Yousee Technology Co., Ltd Product Specification 4 Mechanical Specifications Item Note: Refer to 9 Outline Dimension Drawing Electrical Characteristics

Shenzhen Yousee Technology Co., Ltd Product Specification 5.1.2 Power supply circuit application (This is for reference only): 6 Electro-Optical Specification Item

Shenzhen Yousee Technology Co., Ltd Product Specification Note1: Temp.25ćˈ ˄Angleǃdistance˅ Environmental conditions˖Temp.25ć±3ćˈ65±20%RHˈDark RoomDŽ Distance of OLED display center to measuring machine is 50cmDŽ Note2: Brightness, Brightness Uniformity and Contrast Ratio definition Measure 5 points of Display Brightness. P1~P5. 1) Brightness definition Luminance = [ P1 + P2 + P3 + P4 + P5 ] / 5 2) Brightness Uniformity definition Brightness Uniformity = Y(min) / Y(max) 3) Contrast Ratio definition Dark Room C.R= Luminance (White) / Luminance (Black) Note3: Cross-talk 4% black or white window ˈ117...

Product Specification Shenzhen Yousee Technology Co., Ltd The maximum cross-talk value shall be noted in the measurement report. Note4: Response Time Response time=Pixel turn on and turn off time (White<=>Black). It is measuring transition time from 10% to 90% of luminance.

Product Specification Shenzhen Yousee Technology Co., Ltd

Shenzhen Yousee Technology Co., Ltd Product Specification 8 Recommended Operating Sequence

Shenzhen Yousee Technology Co., Ltd Product Specification 8.1 AC Characteristics (MiPi) 8.1.1 HS Data Transmission Burst Clock Lane Data Lane

Shenzhen Yousee Technology Co., Ltd Product Specification 8.1.4 Timing Parameters Parameter

Shenzhen Yousee Technology Co., Ltd Product Specification 8.1.5 Timing requirements for RESETB When RESETB of the reset pin equals to Low, it will be in the condition of reset. When it is in the condition of reset, it will make the device recover the initial set. However, in order to avoid the reset noise cause reset, there is a mechanism to judge about whether the reset is needed or not. The closed interval of Low can be shown as the following. Shorter than Iresw Normal Operation Initial Condition Figure: Reset timing Table: Reset timing

Product Specification Shenzhen Yousee Technology Co., Ltd

ᢩ䟿ӗ૱ᡀ૱Ӟᓖ‫ޜ‬ᐞѪf⍻ 䈅ᶑԦ,) P$/('9 9a9/(' ᢩ䟿ӗ૱ᡀ૱㢢඀ḷ‫ޜ‬ᐞѪf ᢩ䟿ӗ૱൷रᙗԕк 䇮䇑⌘᜿һ亩˖ മѝ)5$0(9$Ѫ᧘㦀73㿶デս㖞 ǃབྷሿˈᔪ䇞73㿶デս㖞ǃབྷሿн 㾱䎵䗷)5$0(9$DŽ ᮤᵪᵪ༣ᑖ⌑ỹӗ૱ˈᔪ䇞ᇒᡧ ᵪ༣⌑ỹ䘋‫ޕ‬/&'অ䗩000,1 䱢→┿‫ݹ‬DŽ ᮤᵪᵪ༣нᑖ⌑ỹӗ૱ˈᔪ䇞ᇒ ᡧᮤᵪ73Ⲵэঠ唁⋩ᔰデᡆ㘵/(16 эঠ唁⋩ᔰデ∄/&'$$४অ䗩བྷ 000$;DŽ ᇒᡧ䴰‫؍‬䇱䀖᪨ቿл㺘䶒ࡠ⧫⪳ к㺘䶒ᴰቁ

Shenzhen Yousee Technology Co., Ltd Product Specification 11 Handing Precautions 11.2 When cleaning ITO pad, avoid using hard and abrasive material or corrosive solution. 11.3 Keep module away from direct sunlight or fluorescent light, and keep it at room temperature and humidity. 11.4 Strong impact & pressure on module and packing is prohibited. 11.5 Following normal power on/off sequence is necessary for preventing abnormal display or permanent damage to display. 11.6 Optimal contrast ratio under ideal voltage is AMOLED module's characteristic, hence it is recommended a voltage control function...