深圳市万天源光电有限公司 Shenzhen Wanty Photoelectric Co.,Ltd PRODUCT : Wanty Photoelectric SPECIFICATION Revision: 0.0 T070GBP001-V2 This module uses ROHS material This specification may change without prior notice in order to improve performance or quality. Please contact Wanty department for updated specification and product status before design for this product or r

深圳市万天源光电有限公司 Shenzhen Wanty Photoelectric Co.,Ltd REVISION RECORD REV NO. REV DATE 0.0

深圳市万天源光电有限公司 Shenzhen Wanty Photoelectric Co.,Ltd CONTENTS 1、GENERAL INFORMATION 2、EXTERNAL DIMENSIONS 3、ABSOLUTE MAXIMUM RATINGS 4、ELECTRICAL CHARACTERISTICS 5、CTP CHARACTERISTICS 6、ELECTRO-OPTICAL CHARACTERISTICS 7、INTERFACE DESCRIPTION 8、INPUT TIMING 9、RELIABILITY

深圳市万天源光电有限公司 Shenzhen Wanty Photoelectric Co.,Ltd 1、GENERAL INFORMATION Item of general information Module Structure Normally White Viewing Direction Module size (W×H×T) Color Pixel Arrangement Module Interface Type System Support Power Supply Module Power consumption HDMI interface Android/Linux (need to be configured first) Color Numbers

深圳市万天源光电有限公司 Shenzhen Wanty Photoelectric Co.,Ltd

深圳市万天源光电有限公司 Shenzhen Wanty Photoelectric Co.,Ltd 5、CTP CHARACTERISTICS Item of CTP Panel Type Glass Cover + Glass Sensor Surface Hardness Interface Type Support Points Sampling Rate Supply voltage

Average Surface Luminance with all white pixels (PI, P2, P3, P4, P5, P6.P7, PS, P9) Average Surface Luminance with ail black pixels(Pl, P2, P3, P4, P5, P6, P7, PS, P9)

luminance at each test position 1 through 9, and then dividing the maximum luminance of 9points luminance by minimum luminance of 9 points luminance. For more information see Minimum Surface Luminance with all white pixels (PI, P2, P3, PA, P5, P6, PI, P8, P9) Maximum Surface Luminance with all white pixels (PI, P2, P3, PA, PSj P6, PI, P8, P9) Note 4. Response time is the time required for the display to transition from White to black(Rise Time, Tr) and from black to white(Decay Time, Tf). For additional information see FIG 1. Note 5. CIE (x, y) chromaticity ,The x,y value is determined by screen...

深圳市万天源光电有限公司 Shenzhen Wanty Photoelectric Co.,Ltd FIG.2. Measuring method for Contrast ratio, surface luminance, Luminance uniformity, CIE (x , y) chromaticity A : H/6 ; B : V/6 ; H,V : Active Area(AA) size Measurement instrument: BM-7; Light spot size=5mm, 350mm distance from the LCD surface to detector lens.

Application Note: Please connect the USB first, and then connect the HDMI interface. 8> LCD TIMING Horizontal input Timing table

深圳市万天源光电有限公司 Shenzhen Wanty Photoelectric Co.,Ltd 9、RELIABILITY TEST CONDITIONS No. Test Item Test Condition High Temperature Storage High Temperature Operating Temperature Cycle Storage A、Inspection after test: Inspection after 2~4 hours storage at room temperature, the sample shall be free from defects:  Air bubble in the LCD;  Sealleak;  Non-display;  Missing segments;  Glass crack;  Current is twice higher than initial value. B、Remark:  The test samples should be applied to only one test item.  Sample size for each test item is 5~10pcs.  Failure Judgment Criterion: Basic Specification,...

深圳市万天源光电有限公司 Shenzhen Wanty Photoelectric Co.,Ltd 10、INSPECTION CRITERION This specification is made to be used as the standard of acceptance/rejection criteria for TFT-LCD/IPS TFT-LCD module product, and this specification is applicable only in the case that the size of module equal to or exceed than 3.5 inch. 10.1 Sample plan Sampling plan according to GB/T2828.1-2003/ISO 2859-1：1999 and ANSI/ASQC Z1.4-1993,normal level 2 and based on: Major defect: AQL 0.65 Minor defect: AQL 1.5 10.2 Inspection condition Viewing distance for cosmetic inspection is about 30cm with bare eyes, and under an environment...

Zone A: character/Digit area Zone B: viewing area except Zone A (Zone A + Zone B=minimum Viewing area) Zone C: Outside viewing area (invisible area after assembly in customer’s product) Note: As a general rule, visual defects in Zone C are permissible, when it is no trouble for quality and assembly of customer’s product. B > Definition of some visual defect

Inspection standard Bright dot /dark dot defect Zone Note: Minimum distance between defective dots is more than 5mm; Pixel dots’ function is normal, but bright dots caused by foreign material and other reasons are judged by the dot defect of 5.2. 1. Minimum distance between defective dots is more than 5 mm; 2. The quantity of defect is zero in operating condition.

(i) Shifting in position should not exceed the glass outline dimension. (ii) Incomplete covering of the viewing area due to shifting is not allowed. Dirt which can be wiped easily should be acceptable. 5.4.3 Polarizer Dent & Air bubble (i) If the polarizer scratch can be seen after cover assembling or in the operating condition, judge by the linear defect of 5.3. (ii )If the polarizer scratch can be seen only in non-operating condition or some special angle, judge by the following: Using 3% ND filter, it’s NG if it can be seen in R,G,B picture. Visible under: ND3%; D = 0.15mm, Acceptable; 0.15mm<D...

Chips on the corner of terminal shall not be allowed to extend into the ITO pad or expose perimeter seal. It is only applicable to the upper glass of LCD.

深圳市万天源光电有限公司 Shenzhen Wanty