- Catalogs
- Shenzhen Ruicom Technology Co., Ltd.
- RUIOCM LTS6 current output low-power tilt sensor
- Company
- Products
- Catalogs
- News & Trends
- Exhibitions
RUIOCM LTS6 current output low-power tilt sensor
RUIOCM LTS6 current output low-power tilt sensor
The LTS6 series is a high-performance, cost-effective tilt sensor developed by RUICOM Technology. It features an anti-interference platform and next-generation MEMS sensing technology, offering wide temperature adaptability and excellent vibration resistance. The sensor is designed for a 10-year service life and uses a non-contact measurement principle to detect gravitational changes with high precision. It is easy to install and suitable for various applications, including engineering machinery, agricultural equipment, and industrial automation.
Application Scope
The sensor is applicable in agricultural machinery, construction hoisting equipment, aerial work platforms, medical equipment leveling, electric vehicle control systems, and woodworking machinery.
Technical Highlights
- Output: 4 ~ 20 mA
- Voltage input: 9 ~ 36V
- Vibration resistance: >3500g
- Working life: 10 years
Performance Parameters
- Output current: 4 ~ 20 mA
- Resolution: 0.1°
- Measurement accuracy: ±0.2° at 25℃
- Response time: 0.05s
- Temperature drift: -40℃ to +85℃ ±0.5°
- Output load: > 500 ohms
- Insulation resistance: > 100 megaohms
- Vibration resistance: 10 grms 10 ~ 1000 Hz
- Impact resistance: 100g@11 ms, triaxial
- Connector: M12 * 1.0-5 core male head
- Wiring: Standard 2-meter shielded cable
- Size: L64.5 × W50 × H18.5mm
- Weight: ≤200g
Ordering Selection
The model selection includes axis (X, Y, Dual), range (±10° to 360°), signal output (4~20mA), and installation direction (Horizontal, Vertical, etc.). Example: LTS6X10-A1-H indicates X-axis, ±10° range, 4~20mA output, horizontal installation.
Installation and Usage
Ensure the sensing axis is parallel to the tilt axis and the installation surface is flat. The sensor has an IP67 protection level, preventing rainwater and high-pressure water spray but not long-term immersion. Proper wiring is crucial to avoid short circuits.
Interface Definition
- PIN1/Brown: 9 ~36V (Power supply positive)
- PIN2/White: X-axis output
- PIN3/Blue: Y-axis output
- PIN4/Black: GND (Power supply negative)
- PIN5/Grey: Zero clearing
Output Characteristics
The sensor outputs a DC current of 4mA to 20mA, corresponding to the angle measurement range. Example: LTS6D30-A1-H has a range of ±30°, with a 0° output current of 12mA and sensitivity of 0.26667mA/°.
Catalog excerpts
dual axis tilt sensor
Open the catalog to page 1
Technical Highlights ❖ 4 ~20 mA output; ❖ Wide voltage input 9 ~36V; ❖ High vibration resistance >3500g; ❖ Long working life for 10 years. The LTS 6 series current output tilt sensor is a high-performance, cost-effective all-attitude angle measurement product independently developed by RUICOM Technology. Built on an innovative anti-interference platform Equipped with next-generation MEMS sensing technology It has wide temperature range adaptability and excellent vibration resistance. Excellent work stability It is designed to have a service life of up to 10 years. This product uses a non-contact...
Open the catalog to page 2
E.g: LTS6X10-A1 -H: X-axis, ±10° Range, 4~20mA output, horizontal installation. Note: The Range of 0 °~360° is limited to single axis X-axis (clockwise rotation measurement), and the vertical upward installation only.
Open the catalog to page 3
1. This sensor is based on the principle of Earth's gravity angle measurement. During installation, the sensing axis must be parallel to the measured tilt axis, and the installation surface must be flat and tightly fitted to ensure measurement accuracy. 2. Install in the direction selected by the factory. After power on, the current position can be set as the reference zero point through the zero reset command, and the relevant parameters are stored in the built-in memory. 3. IP67 protection level, can prevent rainwater and high-pressure water spray, but long-term immersion is prohibited; Damaged...
Open the catalog to page 4
Measurement direction Note: The product defaults to a horizontal upward installation method at the factory. Users can set the corresponding installation method according to their needs. Please refer to Article 2 of the user manual for the corresponding settings.
Open the catalog to page 5
Output characteristics This product outputs a DC current of 4mA to 20mA, corresponding to the minimum and maximum range of angle measurement. When calculating angles, the corresponding angle values can be obtained by allocating them proportionally; Example: LTS6D30-A1-H: indicates that the angle range of the product is ± 30 °, the output current is 4mA~20mA, and the proportional distribution of 0 ° output current is 12mA, with a sensitivity of 0.26667mA/°. LTS6D0393-A1-H: This indicates that the angle range of the product is -3 ° to+93 °, with an input current of 4mA~20mA. The proportional distribution...
Open the catalog to page 6All Shenzhen Ruicom Technology Co., Ltd. catalogs and technical brochures
- Display module
- Industrial display panel
- Acceleration sensor
- Color display panel
- Tilt sensor
- Digital inclination sensor
- Triaxial acceleration sensor
- Built-in display
- 2-axis tilt sensor
- MEMS inclination sensor
- Multi-axis tilt sensor
- High-precision tiltmeter
- Analog inclination sensor
- IP67 inclination sensor
- Industrial accelerometer
- 1-axis tilt sensor
- MEMS accelerometer
- RS-485 display panel
- Accelerometer with built-in electronics
- Vibration sensor