LTS6 Low-power tilt sensor Product manual V3.0-20260602

Technical Highlights ❖ Zero point can be set on-site; ❖ High vibration resistance >3500g. Product Introduction- The LTS 6 digital output series tilt sensor is a high-performance, cost-effective all-attitude angle measurement device developed based on independent core technologies . This product utilizes an innovative anti-interference structural platform. Integrating next-generation MEMS sensing elements It features wide operating temperature range, excellent resistance to mechanical vibration, and long-term operational stability. It is designed to have a service life of up to 10 years. This...

Signal Output Installation Direction H:Horizontal installation HD:Horizontal downwards V:Vertical installation VD:vertically downward VL:Vertical leftwards VR:Vertical rightwards E.g: LTS6X10-232MB-H: X-axis, ±10° Range, RS232 signal output, MODBUS protocol, horizontal installation. Note: The measurement range of 0°~360° is limited to single axis X-axis (clockwise rotation measurement), and the installation method can only be selected for vertical upward installation. 1. Gravity-based tilt sensor. Align its sensing axis parallel to the target tilt axis with flat, tight mounting surfaces for precision....

Interface Definition Pin/wire color positive power terminal Receive data Send data negative terminal of power supply Product dimensions Shell Size: L64.5×W50×H18.5mm Recommended screws: 2 M4 screws

Measurement direction Mounting surface r777777T. Horizontal installation Mounting surface SfdTuW Horizontal downwards Mounting surface 777777777777777TT7^7rrg7T7777777777777777 t / / / f /1 / / / / 'Ground' ' ' ' ' '' ' ' " Vertical installation vertically downward Mounting surface Mounting surface 777777777777777777^^777777777777777777 Vertical leftwards Vertical rightwards

Serial Communication Protocol- 1. Data frame format: (8-bit data bits, 1 -bit stop bit, no checksum, default rate 9600) Data format: hexadecimal; Data length: the length from data length to checksum (including checksum); Address code: The address of the collection module, which defaults to 00; The data domain varies according to the content and length of the command word; Checksum: The sum of data length, address code, command word, and data field does not consider carry. 2. Command word parsing__

02 10Hz automatic output mode 03 15Hz automatic output mode 04 20Hz automatic output mode command to read the angle before the sensor responds to the relative angle; Automatic output system: After the sensor is powered on, it automatically outputs X and Y angles, and the output frequency is set as shown in the table on the right. (This function can save power off) Sensor response reply command Data Domain (1 byte) E.g: 68 05 00 8C 00 91 The numbers in the data domain represent the results of the sensor response 00: Setting successful FF: Setting failed Set module address command The default address...

2. Read angle data: MODBUS function code 03H_ 8/11

Data word 3, lower 8 bits Data word 3, high 8 bits Data word 4, lower 8 bits Data word 4, high 8 bits CRC Example of application of command to read measurement data 1: 3. Set the relative/absolute zero point of the sensor: Modbus function code 06H_

The above example is to set the byte format to: one start bit+8 data bits without parity+1 stop bit Effective after re powering on. The factory default is a start bit+8 data bit parity+1 stop bit.

Note: 0009 is the register address, which controls the communication character format of the sensor. 0000H: One start bit+8 data bit parity checks+1 stop bit 0001 H: One start bit+8 data bits without checksum+1 stop bit Web:www.ruicomtech.com Tel:0755-23087719 E-mail:[email protected] Add:Building 1, Lixinhu Creative Park, No. 1 Furui Road, Qiaotou Community, Fuhai Subdistrict, Bao'an District, Shenzhen, China