Catalogs >
SHENZHEN RION TECHNOLOGY CO.,LTD >
vibration sensor for wind turbine

vibration sensor for wind turbine
39Pages

Catalog excerpts

RION RAM900S Technical Manual ○INCLINOMETER ○3D COMPASS ○ACCELEROMETER ○GYRO ○NORTH FINDER ○INS&IMU RION TECHNOLOGY SINCE2008 · SENSING AND INDUSTRIAL CONTR

Open the catalog to page 1

RION QUALIFICATION CERTIFICATION ○ Quality management system certification: GB/T19001-2016 idt ISO19001:2015 standard (certificate No.: 128101) ○ Quality Management System Certification: IATF16949:2016 (Certificate No.: T178487) ○ Intellectual property management system certification: GB/T29490-2013 standard (certificate No.: 41922IP00281-06R0M) ○ GJB9001C-2017 standard weapons and equipment quality management system certification (registration No.: 02622J31799R0M) ○ High-tech enterprise (Certificate No.: GR201844204379) ○ Shenzhen Specialized Special New Enterprise (No.: SZ20210879) ○...

Open the catalog to page 2

▶ INTRODUCTION RAM900S Accelerometer is an acceleration sensor independently developed by Rion Technology to detect vibration and shock. It provides accurate acceleration for the control system through CANopen or analog interface. The selected capacitive MEMS sensor has the highest operating accuracy, especially at small amplitudes, where measurement errors due to cross-axis sensitivity are negligible. Therefore, the RAM900S is ideal for the precise acquisition of vibration, such as vibrations on wind turbine towers. Even if the accelerometer is mounted on a solid load-bearing machine part,...

Open the catalog to page 3

Power-on repeatability Bias temperature coefficient Long-term stability Response time Response frequency Axis Bias calibration Resolution Full temperature range working accuracy Power-on start time Output signal CANopen, Analog(current 4~20mA)，Switch (relay switch) Supply voltage Supply current Relay switching threshold Note: CAN bus terminal resistance can be added on request, or remark can be added to PCBA. "|X,Y|" as its level of vehicle body acceleration. ○INCLINOMETER ○3D COMPASS ○ACCELEROMETER ○GYRO ○NORTH FINDER ○INS&IMU RION TECHNOLOGY SINCE2008 · SENSING AND

Open the catalog to page 4

RAM900S Accelerometer ▶ SWITCH OUTPUT CONTROL Relay switching maximum voltage: 30VDC Relay switching maximum current: 1.0A 继电器响应阀值：按用户要求进行设置（默认为|X，Y| = 0.16g). 继电器工作：正确情况下，设备上电后 NO 与 CO 接触闭合（closed)，NC 与 CO 断开(open)。当检测到 |X,Y|的加速度超过所设的阀值时，继电器 NO 与 CO 端断开（Open），NC 与 CO 端接触闭合（close）。 ▶ OUTPUT CONFIGURATION CANopen Filter type Relay trigger time Relay decay value Relay decay time Output Axial Range 3DB bandwidth Relay ID Relay Action Threshold * can provide according to the different configuration, the default relay action thresholds for: 0.16 g (|

Open the catalog to page 5

Color (if with cable） power ground TEST INPUT test input Dark green Analog ground Relay normally open Relay common Relay Normal close CAN_LOW signal light green CAN_HIGH signal test method of the TEST INPUT pin: TEST INPUT---Mainly used for relay testing during maintenance. In order to ensure the normal function of the relay, the user can perform periodical (once a year) maintenance on purpose, and can apply two consecutive high-level signals to the TEST INPUT pin, and the relay will meet the requirements. Perform action switching. ○INCLINOMETER ○3D COMPASS ○ACCELEROMETER ○GYRO ○NORTH...

Open the catalog to page 6

○INCLINOMETER ○3D COMPASS ○ACCELEROMETER ○GYRO ○NORTH FINDER ○INS&IMU RION TECHNOLOGY SINCE2008 · SENSING AND INDUSTRIAL CON

Open the catalog to page 7

RAM900S Accelerometer ▶ CANopen communication protocol 1. Product communication protocol object dictionary（EDS） Index Data/ Object Access Type Device type Error register Manufacturer status register errors/timeouts,etc Contains list of recent Predefined error field Device Name COB-ID SYNC message Hardware version Software version Store Parameters Largest supported sub-index Save all parameters Save communication parameters Save application parameters Save manufacturer parameters Restore default Largest supported sub-index Restore all default parameters communication parameters Restore...

Open the catalog to page 8

Consumer heartbeat Emergency COB-ID Largest supported sub-index Consumer heartbeat time Producer heartbeat time Identity object Largest supported sub-index Product code Revision number Serial number Largest supported sub-index Transmission type Event time Number of mapped objects Baud rate ○INCLINOMETER ○3D COMPASS ○ACCELEROMETER ○GYRO ○NORTH FINDER ○INS&IMU RION TECHNOLOGY SINCE2008 · SENSING AND INDUSTRIAL CONTR

Open the catalog to page 9

Filterband Outputs 2. Detailed specification of communication protocol objects 2.1Communication Profile Area(communication protocol area） 2.1.1OD Index（0x1000): Device Type(device type， UINT32， RO） I. Query device type SDO request message format CAN-ID 0x600+ Node_ID SDO Response message format CAN-ID 0x580+ Node_ID Note：Device Type = 0x0004019A. 2.1.2 OD Index（0x1001): Error Register(error register， UINT8， RO） I. Query the content of the error register and save the latest error type. SDO request message format CAN-ID 0x600+ Node_ID SDO response message format CAN-ID 0x580+ Node_ID Note:...

Open the catalog to page 10

RAM900S Accelerometer SDO response message format CAN-ID 0x580+ Node_ID Note: Manufacturer status Register = 0x00000000. 2.1.4 OD Index（0x1003): Pre-defined error field(pre-defined error field, ARRAY） This object represents errors generated on the CANopen sensor, programmed by the emergency object, and provides error history. 2.1.4.1 Sub-Index:0x00(Number of errors, RW) A. Query the number of errors in the error field If no errors exist, its sub-index 0x00 has the value 0x00. SDO request message format CAN-ID 0x600+ Node_ID SDO response message format CAN-ID 0x580+ Node_ID Note: Number of...

Open the catalog to page 11

RAM900S Accelerometer SDO response message format CAN-ID 0x580+ Node_ID Note: Error Code = 0x03008100。 The upper 16 bits of the Error Code are composed of additional information and the lower 16 bits of the error code. For error codes, please refer to the standard CANopen specification DS-302. 2.1.4.3 Sub-Index:0x02(the 2nd error,UINT32， RO) A. Query Sub-Index 0x02 Second error code SDO request message format CAN-ID 0x600+ Node_ID SDO response message format CAN-ID 0x580+ Node_ID Note: Error Code = 0x04068120。 The upper 16 bits of the Error Code are composed of additional information and...

Open the catalog to page 12

vibration sensor for wind turbine 39Pages

Catalog excerpts

All SHENZHEN RION TECHNOLOGY CO. catalogs and technical brochures

vibration sensor for wind turbine
39Pages