Rion inclinometer SDA116T
1 / 16Pages

SDA116T&SDA126T STRONG ANTI-VIBRATION INCLINOMETER STRONG ANTI-VIBRATION INCLINOMETER Technical Manual

SDA116T&SDA126T STRONG ANTI-VIBRATION INCLINOMETER ○ CE certification number :ATSZAHE190625019 ○ China National Intellectual Property Appearance Patent (Patent No.: ZL 201830753149.6) ○ Revision time:2024-08-07 Note: product functions, parameters and appearance will be adjusted as the technology is upgraded, please confirm with the pre-sales business contact before purchase. Disclaimer This product is developed exclusively for commercial applications and is prohibited from being used for illegal purposes, such as military activities, research related to nuclear, chemical, or biological...

SDA116T&SDA126T STRONG ANTI-VIBRATION INCLINOMETER ▶ DESCRIPTION SDA116T/SDA126T is the MODBUS output type dynamic anti-vibration strong dynamic tilt sensor for industrial field control field. Ensure high-precision measurement of products in a variety of working environments. Use RS485 hardware differential bus to transmit data. Built-in high-precision 16bit A/D differential converter, through the 5th order filtering algorithm, measure the tilt and pitch angle of the sensor output relative to the horizontal plane. Due to the built-in high-precision digital temperature sensor of ADI, the...

SDA116T&SDA126T STRONG ANTI-VIBRATION INCLINOMETER Measure range Measure axis Measure Accuracy Long term stability Zero Temp coefficient Sensitivity temp coefficient Power on time Response time Output rate Output signal Insulation Resistance Anti-vibration Protection glass Standard 1M length、wearproof、grease proofing、wide temperature、Shielded cables 4*0.4mm2, weight ≈40g ▶ ELECTRONIC CHARACTERISTICS PARAMETERS POWER SUPPLY Working current Working temperature Store temperature WORDS EXPLANATION Resolution: The sensor can detect and distinguish the smallest change value of measured within the...

SDA116T&SDA126T STRONG ANTI-VIBRATION INCLINOMETER communication protocol Output Interface Measuring range Installation method Measuring axis Shell sealed 68: RION 68 protocol MB: MODBUS RTU TTL: UART TTL 180: ±180°(Single axis only) E.g:SDA126T-10-232-MB:Standara shell sealed/Dual axis/horizontal installation/±10° 2: bared board,without measure range/RS232 interface/MODBUS communication protocol. ▶ MECHANICAL PARAMETERS ○ Connectors：1m lead cable（length optional） ○ Protection glass：IP67 ○ Material ：Aluminum alloy sanding oxidation ○ Installation ：3*M4 screws ▶ WORKING PRINCIPLE The core...

SDA116T&SDA126T STRONG ANTI-VIBRATION INCLINOMETER SDA116/126 with shell package RS485 electrical connection. ▼ SDA116/126 with shell package RS232 electrical connection.▼ SDA216/226 module electrical connection LINE COLOR GND RS232(RXD) FUNCTI Power Negative Or RS485(D+) ONSn SDA216/226 module RS485 electrical connection. ▼ SDA216/226 module RS232 electrical connection.▼

SDA116T&SDA126T STRONG ANTI-VIBRATION INCLINOMETER MODULE SIZE Shell size: L46×W35.5×H13.9mm Installation size: L37×W28.99mm ounting screws: 4M3 screws SHELL SIZE Shell size: L72.6×W42×H23mm Installation size: L63.5×W34.5×H4mm ounting screws: 3 M4screws

SDA116T&SDA126T STRONG ANTI-VIBRATION INCLINOMETER ▶ INSTALLATION During installation, keep the sensor mounting surface parallel to the measured surface, and avoid the influence of motion and acceleration on the sensor as possible. Please confirm the installation option with sales before ordering. Six installation options as the diagram below:

SDA116T&SDA126T STRONG ANTI-VIBRATION INCLINOMETER ▶ PRODUCTION INSTALLATION NOTES Please according to the correct method to install inclinometer, incorrect installation will create measurement errors, with particular attention to the "surface", "line":： 1）The Sensor installation surface and the measured surface must be fixed closely, stability,if the install surface unflat, may be created measuring angle error of sensor . 2) The sensor axis and the measured axis must be parallel ,and two axis try not to appear angle.

SDA116T&SDA126T STRONG ANTI-VIBRATION INCLINOMETER ▶ COMMUNICATION PROTOCOL 1. Data frame format: (8 data bits, 1 stop bit, no check, default rate 9600) Command Identifier Data length Address checksum word Data field (1byte) (1byte) code (1byte) (1byte) (1byte) 68 Data format: hexadecimal Identifier: fixed at 68 Data length: the length from data length to checksum (including checksum) Address code: the address of the acquisition module, the default is 00 The data field changes according to the different content and length of the command word. Checksum: The sum of data length, address code,...

SDA116T&SDA126T STRONG ANTI-VIBRATION INCLINOMETER Set relative/absolute zero: You can set the current angle to zero degrees for relative measurement, or you can set it back to the absolute factory zero degree, save after power off Example: 68 05 00 05 00 0A Sensor response reply command example: 68 05 00 85 00 8A Set communication speed Example: 68 05 00 0B 03 13 This command is set to take effect after power off and restart, and save function at power off Sensor response reply command example: 68 05 00 8B 90 Set sensor output mode Response system: The upper computer needs to send read the...

SDA116T&SDA126T STRONG ANTI-VIBRATION INCLINOMETER 0X0F Set module address command The default address of the sensor is 00, 1.If multiple sensors are connected to a group of buses at the same time, such as RS485, each sensor needs to be set to a different address to achieve separate control and response angles. 2.If the new address is successfully changed, the address code in all subsequent commands and response packets must be replaced with the new address code after the change to be effective, otherwise the sensor will not respond to the command. This command is a power-off save function....

SDA116T&SDA126T STRONG ANTI-VIBRATION INCLINOMETER ▶ RION PRODUCTS MODBUS COMMUNICATIONS PROTOCOL Please read the following items carefully before using: 1) MODBUS protocol stipulates that it should be over 3.5 byte time between two data frame(Eg. Under 9600 baud rate, the time is 3.5× （ 1/9600 ） ×11=0.004s ). This sensor increase the time to 10ms for a enough margin, so please set 10ms time interval at least between each data frame. Host send command--10ms interval--slave response command--10ms time interval--host send command... 2) MODBUS protocol stipulates broadcast address---content...