Rion inclinometer LCA316T
1 / 16Pages

Appearance patent no.：ZL 201830752874.1 DIGITAL SINGLE/DUAL AXIS INCLINOMETER

○ CE certification: AT18250EC100244 ○ RoHS certification:18300RC20410801 ○ China National Intellectual Property Appearance Patent (Patent No.: ZL 201830752874.1) ○ Revision time:2024-08-06 Note: Product functions, parameters, appearance, etc. will be adjusted as the technology upgrades. Please contact our pre-sales business to confirm when purchasing. Disclaimer This product is developed exclusively for commercial applications and is prohibited from being used for illegal purposes, such as military activities, research related to nuclear, chemical, or biological weapons, or any other...

▶ PRODUCT INTRODUCTION LCA316T / LCA326T series products are a new generation of digital small volume MEMS tilt sensor launched by RION Technology. It has a built-in dual-channel earth gravity tilt unit, which can be converted into tilt angle changes by measuring static gravity acceleration. So that the tilt angle of the sensor output relative to the horizontal plane can be measured. Output method RS232, RS485 or TTL. Because it is a built-in MCU control system, which correct the linearity of the sensor output twice, making up the accuracy drop for the analog type because of insufficient...

Measure range Measure axis Zero Temp. coefficient Sensitivity temp. coefficient Power on start time response frequency Measure accuracy Output rate Output signal Insulation Resistance Shockproof ≥100 MΩ 100g@11ms、3 Axial Direction (Half Sinusoid) Protection grade Cables Weight IP67 standard configuration: 1 meter wearproof、grease proofing、 wide temperature、Shielded cables 4*0.3mm2 ≤135g (including 1 meter cable) KEY WORDS Resolution: It refers to the smallest change value that the sensor can detect and distinguish in the measurement range. Measure accuracy: Refers to the combined error of...

▶ ELECTRICAL PARAMETERS PARAMETERS Power supply voltage Working current Working temp. Store temp. Output Interface Measure range Installation method Measure axis Shell sealed 3: Standara shell sealed E.g.: LCA326T-10-232-68：Standara shell sealed / Dual axis / standard type / ± 10 ° measure range / RS232 output / Rion 68 protocol. ▶ MECHANICAL PARAMETERS ○ Connector: 1m straight lead (customizable) ○ Protection level: IP67 ○ Shell material: aluminum alloy frosted and oxidized ○ Inst

▶ WORKING PRINCIPLE Adopt imported core control unit and apply the principle of capacitive micro-pendulum. Using the principle of earth's gravity, when the tilting unit tilts, the earth's gravity will produce a gravitational component on the corresponding pendulum, and the corresponding electric capacity will change. By amplifying and filtering the electric capacity, the inclination angle is obtained after conversion. ▶ELECTRICAL CONNECTION Color Function Power negative Power positive Power negative Power positive PCBA electrical connection Color Function

SHELL electrical connection ▶ SIZE PCBA SIZE

LCA316T/LCA326T DIGITAL INCLINOMETER SHELL SIZE Shell size: L55×W37×H24mm Installation size: L48×W28.6×H4mm ounting screws: 3 M4 screws ▶ INSTALLATION DIRECTION During installation, keep the sensor mounting surface parallel to the target surface to be measured, and reduce the impact of dynamics and acceleration on the sensor. This product can be installed horizontally or vertically, please refer to the following diagram for the installation method:

▶ INSTALLATION PRECAUTIONS Please install the tilt sensor according to the correct method. Improper installation will cause measurement error. Pay attention to the first "surface" and the second "line": 1) The mounting surface of the sensor and the measured surface must be tight, flat and stable. The unevenness of the mounting surface is easy to cause the angle error of the sensor measurement. 2) The axis of the sensor and the axis to be measured must be parallel, and the angle between the two axes should be avoided as much as possible. ▶ RION PRODUCT COMMUNICATION PROTOCOL 1. Data frame...

Set relative / absolute zero: The current angle can be set to zero degrees for relative measurement, or it can be set back to the absolute factory zero degree and save after power off E.g: 68 05 00 05 00 0A Sensor response reply command E.g.: 68 05 00 85 00 8A Set communication speed E.g.: 68 05 00 0B 03 13 This command is set to take effect after power off and restart, and save function after power off Sensor response reply command E.g.: 68 05 00 8B 00 90 Set sensor output mode Response system: The upper computer needs to read the angle command before the sensor responds 11 / 16 Data field...

to the relative angle Automatic output system: After the sensor is powered on, X, Y angles are automatically output, and the output frequency is set as shown in the table on the right. (This function has power off memory) E.g.: 68 05 00 0C 00 11 Sensor response reply command E.g.: 68 05 00 8C 00 91 Set module address command The default address of the sensor is 00, 1.If multiple sensors are connected to a group of buses at the same time, such as RS485, each sensor needs to be set to a different address to achieve separate control and response angles. 2.If the new address is successfully...

LCA316T/LCA326T DIGITAL INCLINOMETER 00 : Success 0X0D Query relative / absolute zero Used to query whether the current zero-degree mode of the sensor is relative zero or absolute zero E.g.: 68 04 00 0D 11 Sensor response reply command Example:68 05 00 8D 00 92 Data field (0byte) No data field command Data field (1byte), The number in the data field indicates the result of the sensor response 00 Absolute zero point 01 Relative zero point ▶ RION PRODUCT MODBUS COMMUNICATION PROTOCOL Note, please read the following items carefully before use: 1) Because the MODBUS protocol stipulates that the...

LCA316T/LCA326T DIGITAL INCLINOMETER 2. Read angle data Modbus function code 03H Host query command: Slave response: Sensor address Sensor address function code function code Access register First address Data length Data word 1 high 8 bits Data length Data word 1 low 8 bits Data word 2 high 8 bits Data word 2 lower 8 bits Data word 3 high 8 bits Data word 3 lower 8 bits Data word 4 high 8 bits Data word 4 lower 8 bits Read measurement data command example 1:： Host sends Note: The data field of the slave reply frame is 50H, 46H, 00H, 00H, 23H, 20H, 00H, 00H The X axis is the first 1-4 bytes...