ACA616T/ACA626T-CAN2.0A OUTPUT tilt sensor PATENT NO：ZL 201830752872.2 CE certification: AT011611743E FCC certification: AT011611744E RoSH certification: 18300RC20410801 CAN2.0A OUTPUT TILT SENSOR Technical Manual

ACA616T/ACA626T-CAN2.0A OUTPUT tilt sensor RION PRODUCT QUALIFICATION ○ CE certification: AT011611743E ○ FCC certification: AT011611744E ○ RoHS certification: 18300RC20410801 ○ Revision time:2024-08-06 Note: Product functions, parameters, appearance, etc. will be adjusted as the technology upgrades. Please contact our pre-sales business to confirm when purchasing. Disclaimer This product is developed exclusively for commercial applications and is prohibited from being used for illegal purposes, such as military activities, research related to nuclear, chemical, or biological weapons, or any other...

ACA616T/ACA626T-CAN2.0A OUTPUT tilt sensor ▶ GENERAL DESCRIPTION ACA616T/ACA626T-CAN2.0A is a full-temperature compensated high-precision single / dual-axis tilt sensor developed by RION Technology on the basis of high-precision inclination platform. Its good temperature stability can be used in a wide temperature environment of -40~85℃ In addition, the system has a built-in high-precision 24it A/D converter, and through a 5-level conversion algorithm, it can measure the tilt and pitch angle of the sensor output relative to the horizontal plane. Output protocol CAN2.0A. The characteristics of...

ACA616T/ACA626T-CAN2.0A OUTPUT tilt sensor Measure range Measure axis Measure accuracy Long term stability Zero Temp. coefficient Sensitivity temp-coeffi Power on time Response frequency Output rate Interface type Insulation Resistance Shockproof ≥100MΩ 100g@11ms、3 Axial Direction (Half Sinusoid) 10grms、10～1000Hz Anti-vibration Protection grade Cables Weight IP67 Standard configuration: 2m length, wear-resistant, wide temperature, shielded cable 5P * 5.7mm aviation connector 235g(without cable) KEY WORDS: Resolution : Refers to the sensor in measuring range to detect and identify the smallest...

ACA616T/ACA626T-CAN2.0A OUTPUT tilt sensor Output Interface Measure range Installation Direction Measure axis 1: Single Axis 2: Dual Axis E.g：ACA616T-10-C2：single Axis /Horizontal /±10° measure range /CAN2.0A output . ▶ MECHANICAL PARAMETERS ○ Connectors：Air Plug Connector (1m Direct Leading Cable Can Be Customized ) ○ Enclosure Material ：Aluminum Oxide ○ Installation ：4*M4 Screws 2*3mm Plug Position ▶ WORKING PRINCIPLE Adopt imported core control unit and apply the principle of capacitive micro-pendulum. Using the principle of earth's gravity, when the tilting unit tilts, the earth's gravity...

ACA616T/ACA626T-CAN2.0A OUTPUT tilt sensor Definition of aerial patch cord COLOR FUNCTION Vcc 9～36V Positive power supply size: L92×W48×H36mm Installation size: L82*W48*H6mm Mounting screws: 4 M4 screws/2 M3 positioning pins

ACA616T/ACA626T-CAN2.0A OUTPUT tilt sensor ▶ PRODUCTION INSTALLATION NOTES Please follow the correct way to install tilt sensor, incorrect installation can cause measurement errors, with particular attention to the "surface", "line" : 1) The Sensor mounting surface and the measured surface must be fixed closely, stability,if mounting surface uneven likely to cause the sensor to measure the angle error. 2) The sensor axis and the measured axis must be parallel ,the two axes do not produce the angle as much as possible.

ACA616T/ACA626T-CAN2.0A OUTPUT tilt sensor ▶ MEASURING DIRECTIONS The installation must guarantee the product bottom is parallel to measured face，and reduce the influence of dynamic and acceleration to the sensor. This product can be installed horizontally or mounted vertically (mounted vertically selection must confirm before production ), for installation please refer to the following scheme.

ACA616T/ACA626T-CAN2.0A OUTPUT tilt sensor ▶ RION PRODUCT COMMUNICATION PROTOCOL 1):Modify the node number, the ID bit width is 11 bits, and the default node number is 0x05 CAN-ID Table 1-3 Request message format CAN-ID Table 1-4 Response message format Note: If the controller sends CAN-ID=0x600+0x05, send data: 40 10 10 00 10 00 00 00 The sensor returns CAN-ID=0x580+0x05 (default), and the return data: 40 10 10 00 10 00 00 00 After power on again, the received frame ID is 0x590 (0x580+0x10), indicating that the frame ID is modified successfully. 2) Set CAN baud rate CAN-ID Table 1-5 Request...

ACA616T/ACA626T-CAN2.0A OUTPUT tilt sensor For example，XL=0x43，XM=0x53，XH=0x02,Xsign=0x01，The angle is -15.2387, and the conversion process is as follows: XH XM XL 0x02 0x53