Catalogs >
SHENZHEN RION TECHNOLOGY CO.,LTD >
LCA310T single axis inclinometer/level detection

LCA310T single axis inclinometer/level detection
7Pages

Catalog excerpts

LCA310T single axis inclinometer/level detection - 1

LCA310T- Voltage Type Single-axis Inclinometer SPECIFICATIONS Item No.LCA310T DescriptionVoltage Type Single-axis Inclinometer Production implementation standard reference ● Enterprise quality system standards: ISO9001: 2008 standard (certification number: 128101) ● Tilt sensor production standards: GB / T 191 SJ 20873-2003 inclinometer general specification of Level ●The Academy of metrology and quality inspection Calibrated in accordance to: JJF1119-2004 Electronic Level calibration Specification ● Gyro accelerometer test standard: QJ 2318-92 Gyro accelerometer test methods ● Software development reference standard: GJB 2786A-2009 military software development General requirements ● Product environmental testing standards: GJB150 ● Electromagnetic anti-interference test standards: GB / T 17626 ●Ver:.06 ●Date:2014.8.1

Open the catalog to page 1

LCA310T single axis inclinometer/level detection - 2

LCA310T- Voltage Type Single-axis Inclinometer General Description The LCA310T series inclinometer, developed by Rion Company for market with requirement on volume and cost, is a small volume low-cost single-axis tilt sensor. The output voltage goes through an internal secondary linearity correction, it is a linearity voltage output tilt sensor. Due to the latest built-in MEMS technology inclination unit, it achieves small size, low power consumption, high consistency and stability, working temperature up to the industry level -40 to +85, it is a ultra-high cost-effective inclination...

Open the catalog to page 2

LCA310T single axis inclinometer/level detection - 3

LCA310T-Voltage Type Single-axis Inclinometer Ordering information: -* 3: Standard shell sealed without shell E.g: LCA310T-10-v1: Single-axis/Standard /±10°Measuring range/0-5V output voltage Technical Data ZERO output Long term Response time Standard 1M length* wearproof* grease proofing* wide temperature* This Technical data only list ± 30 °, ± 60 °, ± 90 °, ± 360 ° series for reference, other measuring range RION TECHNOLOGY

Open the catalog to page 3

LCA310T single axis inclinometer/level detection - 4

LCA310T-Voltage Type Single-axis Inclinometer please refer to the adjacent parameters. Electronic Characteristics Resolution: Refers to the sensor in measuring range to detect and identify the smallest changed value. Absolute accuracy: Refers to in the normal temperature circumstances,the sensor absolute linearity, repeatability, hysteresis, zero deviation, and transverse error comprehensive error. Long term stability : Refers to the sensors in normal temperature conditions, the deviation between the maximum and minimum values after a year's long time work. Response time: Refers to the...

Open the catalog to page 4

LCA310T single axis inclinometer/level detection - 5

LCA310T-Voltage Type Single-axis Inclinometer Measuring Directions&Fix The installation must guarantee the product bottom is parallel to measured face, and reduce the influence of dynamic and acceleration to the sensor. This product can be installed horizontally or mounted vertically (mounted vertically selection is only applicable to the single axis), for installation please refer to Angle output calculation formula Angle=(output voltage—Zero position voltage^Angle sensitivity Angle sensitivity=output voltage range-r Angle measuring range E.g: LCA310T-30-V1 (±30° Measuring range 0~5V...

Open the catalog to page 5

LCA310T single axis inclinometer/level detection - 6

LCA310T-Voltage Type Single-axis Inclinometer Production installation notes: Please follow the correct way to install tilt sensor, incorrect installation can cause measurement errors, with particular attention to the "surface", "line":: 1) The Sensor mounting surface and the measured surface must be fixed closely, smoothly, stability,if mounting surface uneven likely to cause the sensor to measure the angle error. See Figure Pic.AB 2) The sensor axis and the measured axis must be parallel ,the two axes do not produce the angle as much as possible. See Figure Pic.CD Electrical Connection...

Open the catalog to page 6