CUSTOMER : CUSTOMER MODULE : HL MODEL  Preliminary Specification ■Final Specification Customer Confirmation column： Approved by : Please return one of the copies of the specification with your signature to us within two weeks after you receive this document.If it is not returned,we will assume that you agree to the entire contents of this specification document. HongGuang Display Co.,Ltd

深圳市鸿光显示有限公司 REVISION HISTORY (● )preliminary specification ( )Final specification Revision No. Initial Release HongGuang Display Co.,Ltd

General Description Absolute Maximum Ratings Electrical Specifications Optical Specifications Interface Connection Signal Timing Specifications Signal Timing Waveforms of Interface Signal Input Signals, Display Colors & Gray Scale of Colors Power Sequence Mechanical Characteristics Reliability Test Handling& Cautions Product Serial Number HongGuang Display Co.,Ltd

深圳市鸿光显示有限公司 1.0 GENERAL DESCRIPTION 1.1 Introduction HG215FH008T02 is a color active matrix TFT LCD module using amorphous silicon TFT' s (Thin Film Transistors) as an active switching devices. This module has a 21.5 inch diagonally measured active area with FHD resolutions (1920 horizontal by 1080 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and this module can display 16.7M colors. The TFT-LCD panel used for this module is adapted for a low reflection and higher color type. LVDS Input Signal LVDS Rx + T/CON + Mini LVDS Tx DC/DC...

深圳市鸿光显示有限公司 1.3 Application  Desktop Type of PC & Workstation Use  Slim-Size Display for Stand-alone Monitor  Display Terminals for Control System  Monitors for Process Controller 1.4 General Specification The followings are general specifications at the model HG215FH008T02. Active area Pixel pitch Pixel arrangement Display colors Display mode Normally Black Dimensional outline Bezel width (L/R/U/D) Surface Treatment Lower side 1-LED Light bar Type HongGuang Display Co.,Ltd

深圳市鸿光显示有限公司 2.0 ABSOLUTE MAXIMUM RATINGS The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and non-operational maximum voltage and current values are listed in Table 2. < Table 2. Absolute Maximum Ratings> [VSS=GND=0V] Parameter Power Supply Voltage Logic Supply Voltage Operating Temperature Storage Temperature Note : 1) Temperature and relative humidity range are shown in the figure below. Wet bulb temperature should be 39 OC max. and no condensation of water. (39,90)

深圳市鸿光显示有限公司 3.0 ELECTRICAL SPECIFICATIONS 3.1Electrical Specifications [Ta =25± 2 ℃] < Table 3. Electrical specifications > Power Supply Voltage Power Supply Current In-Rush Current Permissible Input Ripple Voltage High Level Differential Input Threshold Voltage Low Level Differential Input Threshold Voltage Differential input voltage Differential input common mode voltage Power Consumption Notes : 1. The supply voltage is measured and specified at the interface connector of LCM. The current draw and power consumption specified is for VDD=5.0V, Frame rate=75Hz. Test Pattern of power supply current...

LED Light Bar Input Voltage Per Input Pin LED Light Bar Input Current Per Input Pin LED bar consists of 72 LED packages,3 strings(parallel)*24packages(serial) Note1: There are one light bar ,and the specified current is input LED chip 100% duty current Note2: The sense current of each input pin is 80mA Note3: PBL=3 Input pins*VPIN × IPIN Note4: The lifetime is determined as the time at which luminance of LED become 50% of the initial brightness or not normal lighting at IPIN=80mA on condition of continuous operating at 25 ± 2 ℃ HongGuang Display Co.,Ltd

深圳市鸿光显示有限公司 4.0 OPTICAL SPECIFICATION 4.1 Overview The test of Optical specifications shall be measured in a dark room (ambient luminance  1 lux and temperature = 252℃) with the equipment of Luminance meter system (Goniometer system and TOPCONE PR730) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of θ and Φ equal to 0. We refer to θØ=0 (=θ3 ) as the 3 o’clock direction (the “right”), θØ=90 (= θ12 ) as the 12 o’clock direction (“upward”), θØ=180 (= θ9 ) as the 9 o’clock direction (“left”) and θØ=270(= θ6 ) as the 6 o’clock direction (“bottom”)....

Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock direction with respect to the optical axis which is normal to the LCD surface. Contrast measurements shall be made at viewing angle of = 0 and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. (See FIGURE 1 shown in Appendix) Luminance Contrast Ratio (CR) is defined mathematically. CR Luminance when displaying a white...

深圳市鸿光显示有限公司 5.0 INTERFACE CONNECTION. 5.1 Electrical Interface Connection 5.1.1 LED Light Bar -LED connector： 3707K-Q06N-08X manufactured by Entry < Table 5. LED Light Bar> Pin No HongGuang Display Co.,Ltd

深圳市鸿光显示有限公司 5.2 Electrical Interface Connection ● Module Side Connector : UJU IS100-L30R-C23or Equivalent User Side Connector : JAE FI-X30H or Equivalent Negative Transmission data of Pixel 0 (ODD) Positive Transmission data of Pixel 0 (ODD) Negative Transmission data of Pixel 1 (ODD) Positive Transmission data of Pixel 1 (ODD) Negative Transmission data of Pixel 2 (ODD) Positive Transmission data of Pixel 2 (ODD) Bist function Negative Transmission Clock (ODD) Positive Transmission Clock (ODD) Negative Transmission data of Pixel 3 (ODD) Positive Transmission data of Pixel 3 (ODD) Negative Transmission...

深圳市鸿光显示有限公司 5.2 LVDS Interface (Tx; THC63LVDF83A or Equivalent) 5.2.1 LVDS Interface Input Signal HongGuang Display Co.,Ltd