CUSTOMER MODULE :_ □Preliminary Specification ■Final Specification Customer Confirmation column: Approved by :Dept. :Data : Please return one of the copies of the specification with your signature to us within two weeks after you receive this document.If it is not returned,we will assume that you agree to the entire contents of this specification document.

REVISION HISTORY(• preliminary specification ( )Final specification Revision No. HongGuang Display Co.,Ltd

深圳市鸿光显示有限公司 1.0 GENERAL DESCRIPTION 1.1 Introduction HG215FH008 is a color active matrix TFT LCD module using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This module has a 21.5 inch diagonally measured active area with FHD resolutions (1920 horizontal by 1080 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and this module can display 16.7M colors. The TFT-LCD panel used for this module is adapted for a low reflection and higher color type. LVDS Input Signal LVDS Rx + T/CON + Mini LVDS Tx DC/DC Gamma...

1.3 Application • Desktop Type of PC & Workstation Use • Slim-Size Display for Stand-alone Monitor • Display Terminals for Control System • Monitors for Process Controller 1.4 General Specification The followings are general specifications at the model HG215FH008. <Table 1. General Specifications>

深圳市鸿光显示有限公司 2.0 ABSOLUTE MAXIMUM RATINGS The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and non-operational maximum voltage and current values are listed in Table 2. < Table 2. Absolute Maximum Ratings> [VSS=GND=0V] Parameter Power Supply Voltage Logic Supply Voltage Operating Temperature Storage Temperature Note : 1) Temperature and relative humidity range are shown in the figure below. Wet bulb temperature should be 39 OC max. and no condensation of water. (39,90)

3.0 ELECTRICAL SPECIFICATIONS 3.1Electrical Specifications < Table 3. Electrical specifications > [Ta =25 — 2 C ] Parameter Notes : 1. The supply voltage is measured and specified at the interface connector of LCM. The current draw and power consumption specified is for VDD=5.0V, Frame rate=75Hz. Test Pattern of power supply current a) Typ : Color Bar pattern b) Max : Gray level 255 pattern 2. Duration of rush current is about 2 ms and rising time of VDD is 520 ps ± 20 % 3. Calculated value for reference (VL x IL) X 3(channel) excluding driver loss. (LED Light bar: 24S3P)

LED bar consists of 72 LED packages,3 strings(parallel)*24packages(serial) Notel: There are one light bar ,and the specified current is input LED chip 100% duty current Note2: The sense current of each input pin is 80mA Note3: PBL=3 Input pins*VPlN X IPin Note4: The lifetime is determined as the time at which luminance of LED become 50% of the initial brightness or not normal lighting at IPIN=80mA on condition of continuous operating at 25 + 2 °C

4.0 OPTICAL SPECIFICATION 4.1 Overview The test of Optical specifications shall be measured in a dark room (ambient luminance < 1 lux and temperature = 25+2°C) with the equipment of Luminance meter system (Goniometer system and TOPCONE PR730) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of 0 and ® equal to 0°. We refer to 00=o (=03) as the 3 o’clock direction (the “right”), 00=9O (= 012) as the 12 o’clock direction (“upward”), 00=18O (= 09) as the 9 o’clock direction (“left”) and 00=27O(= 06 ) as the 6 o’clock direction (“bottom”). While...

Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock direction with respect to the optical axis which is normal to the LCD surface. Contrast measurements shall be made at viewing angle of = 0 and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. (See FIGURE 1 shown in Appendix) Luminance Contrast Ratio (CR) is defined mathematically. CR Luminance when displaying a white...

深圳市鸿光显示有限公司 5.0 INTERFACE CONNECTION. 5.1 Electrical Interface Connection 5.1.1 LED Light Bar -LED connector： 3707K-Q06N-08X manufactured by Entry < Table 5. LED Light Bar> Pin No HongGuang Display Co.,Ltd

5.2 Electrical Interface Connection • CN11 Module Side Connector : UJU IS100-L30R-C23or Equivalent User Side Connector : JAE FI-X30H or Equivalent Note 1 : H: White-Black-Red-Green-Blue Pattern Aging, L:Black pattern , when no LVDS signal Note2: This pin should be connected with GND.

5.2 LVDS Interface (Tx; THC63LVDF83A or Equivalent) 5.2.1 LVDS Interface

6.0 SIGNAL TIMING SPECIFICATION 6.1 The HG215FH008 is operated by the DE only. Note 1 : This DCLK range at last line of V-blanking should be set in 0~987.

深圳市鸿光显示有限公司 6.2 LVDS Rx Interface Timing Parameter The specification of the LVDS Rx interface timing parameter is shown in Table 4. Item CLKIN Period Input Data 0 nsec nsec nsec nsec nsec * Vdiff = (RXz+)-(RXz-),…. ,(RXCLK+)-(RXCLK-)

深圳市鸿光显示有限公司 7.0 SIGNAL TIMING WAVEFORMS OF INTERFACE SIGNAL 7.1 Sync Timing Waveforms H-Sync Fix H-Sync width Area 1) Need over 3 H-sync during V-Sync Low 2) Fix H-Sync width from V-Sync falling edge to first rising edge 7.2 Vertical Timing Waveforms Invalid Data HongGuang Display Co.,Ltd

深圳市鸿光显示有限公司 7.3 Horizontal Timing Waveforms HongGuang Display Co.,Ltd

深圳市鸿光显示有限公司 8.0 INPUT SIGNALS, BASIC DISPLAY COLORS & GRAY SCALE OF COLORS Color & Gray Scale Basic Colors Gray Scale of GREEN Gray Scale of BLUE Gray Scale of WHITE Black Blue Green Cyan Red Magenta Yellow White Black △ Darker △ ▽ Brighter ▽ Red Black △ Darker △ ▽ Brighter ▽ Green Black △ Darker △ ▽ Brighter ▽ Blue Black △ Darker △ ▽ Brighter ▽ White HongGuang Display Co.,Ltd