HG170SX006T01
20Pages

Catalog excerpts

specification for tft lcd modulecustomer :customer module :_ HLMODEL : -HG170SX006T01 Customer Confirmation column: Approved by : Dept. :Data : Please return one of the copies of the specification with your signature to us within two weeks after you receive this document.If it is not returned,we will assume that you agree to the entire contents of this specification document. HongGuang Display Co.,Ltd

Open the catalog to page 1

深圳市鸿光显示有限公司 Revision History Version NO. HongGuang Display Co.,Ltd FIRST ISSUE

Open the catalog to page 2

深圳市鸿光显示有限公司 CONTENTS GENERAL INFORMATION ELECTRICAL CHARACTERISTICS ELECTRO-OPTICAL CHARACTERISTICS RELIABILITY TEST CONDITIONS INSPECTION STANDARDS PACKAGE DRAWING HongGuang Display Co.,Ltd

Open the catalog to page 3

1. GENERAL INFORMATION 1.1 features 1) Structure: LCM+CTP 2) TN Type LCD 1280 dot-segment and 1024 dot-common outputs 3) 16.7M Color can be selected by software 4) White LED back light 5) Dual Channel LVDS interface

Open the catalog to page 4

HongGuang Display Co.,Ltd

Open the catalog to page 5

4. Electrical Characteristics 4.1 ABSOLUTE MAXIMUM RATINGS (GND=AGND=0V) Nate 3-1: Ifirush Cur lent i Measurement; Test oircuit;

Open the catalog to page 7

4.4 Color versus Input Data The following table is for color versus input data (8bit). The higher the gray level, the brighter the color.

Open the catalog to page 8

4.5 LVDS Specification 4.5.1 DC Characteristics: Symbol Use RxOCLK- & RxOCLK+ as example.

Open the catalog to page 9

4.6 Input Timing Specification It only support DE mode, and the input timing are shown as the following table. Note 3-3? The equal an 5 listed as loi lowing ^Igase don't exceed Lhg above recommended value Fh [Mir.1 = fclk tM n.j / Tfi 1M n.j-Fh i'Typ.J = Fclk (Typ.1 ftlh (Typ.)1 Fh (Max.)=i FclklMax.J / Th (Mm.j. Note 3-4; The equal cn g listed as isilowing ^lease don't exceed Lhg above recommended value Fclk 1M n.t = Fv (Mr.) x Th (Mir.) x Tv (Min ); Folk iTyp.) = Fv -:Typ.J xTh (Typ.} x Tv (Typ.y Fcxh [Max.) = Fv (Max.) xTh (Typ.) x Tv (Typ.);

Open the catalog to page 10

4.7 Input Timing Diagram 4.8 Power ON/OFF Sequence VDD power,LVDS signal and backlight on/off sequence are as following. LVDS signals from any system shall be Hi-Z state when VDD is off. I.VDS SiynLjJ HongGuang Display Co.,Ltd

Open the catalog to page 11

Power Sequence Timing Symbol Note 3-5 : Recommend selling IS = Oms lo avoic electronic noise when VDD s otl Note 3-6: During T5 mid Tfi period please k^ep the nr Enput :_VDS s.rjnals with Hr-Z slate 4.9 Backlight Unit The following shows the block diagram of the 17 inch Backlight Unit. And it includes 36 pcs LED in the LED light bar. (4 strings and 9 pcs LED of one string). HongGuang Display Co.,Ltd HG170SX006T01 12/20

Open the catalog to page 12

Note 4-1: Vs (Typ.) = V F (Typ.) X LED No. (one string); a. V F : LED chip forward voltage, V F (Min.)=2.8V, V F (Typ.)=3.2V, V F (Max.)=3.6V b. The same euqation to calculate Vs(Min.) & Vs (Max.) for respective V F (Min.) & V F (Max.); Note 4-2: AVs (Max.) = AV F X LED No. (one string); a. AV F: LED chip forward voltage deviation; (0.2 V , each Bin of LED V F ) Note 4-3: P BLU (Typ.) = Vs (Typ.) X Is (Typ.) X 4 ; ( 4 is total String No. of LED Light bar) P BLU (Max.) = Vs (Max.) X Is (Max.) X 4 ; Note 4-4: Definition of life time: a. Brightness of LED becomes to 50% of its original value...

Open the catalog to page 13

5. ELECTRO-OPTICAL CHARACTERISTICS Parameter

Open the catalog to page 14

Notel Definition of Contrast Ratio (CR): hk , Lumiriance measured when LCD on the White" state Contrast ratio (CRj — -Lumi n a nee mea su red wtie n L CD on the " 3 lack1' state Note2: Definition of Luminance Uniformity: Active area is divided into 9 measuring areas (Shown in below), every measuring point is placed at the center of each measuring area. , Bmin H/6 Luminance Uniformity = V/6 B • Bmax-Bmax: The measured maximum luminance of all measurement position. Bmin: The measured minimum luminance of all measurement position. Note 3:Definition of Response time: Sum of Trand Tf Display...

Open the catalog to page 15

深圳市鸿光显示有限公司 Note4.Definition of Viewing Angle: The viewing angle range that the CR≥10 Note 5: Definition of Color Chromaticity (CIE 1931) Color coordinate of white & red, green, blue at center point.

Open the catalog to page 16

1. The reliability items will be fully performed in new sample qualification, 2 .The reliability status will be tested as monitor during mass production. Individual reliability test shall be performed by lot, Moreover, the individual reliability item shall be decided according to reliability plan. 3. All samples are inspected after keeping in the room with normal temperature and humidity for 2 hours or above. 4. Vibration test: It is not necessary to test for those products without assembly frame , backlight, PCB and so on. 5. Dropping test: It is necessary for affirming new package. 6. For...

Open the catalog to page 17

HongGuang Display Co.,Ltd ）等维纤、屑毛、伤划感无、伤磨（陷缺状线）内以寸 2.6（：准标定判线、点寸尺小。等等)时要必(镜微显体实,镜大放,尺卡标游,卡比对林菲,机片单及线源电,板主,架测测电:具工验检 9.2.7 。秒 3-秒 1：间时验检，XUL0001-XUL006 为度照 :境环验检观外,下以 XUL002 为度照:境环验检测

Open the catalog to page 18