HG133FH017T01
32Pages

Catalog excerpts

SPECIFICATION FOR TFT LCD MODULE CUSTOMER : CUSTOMER MODULE :_ □Preliminary Specification ■ Final Specification Customer Confirmation column: Approved by : Dept. :Data : Please return one of the copies of the specification with your signature to us within two weeks after you receive this document.If it is not returned,we will assume that you agree to the entire contents of this specification document. HongGuang Display Co.,Ltd

Open the catalog to page 1

深圳市鸿光显示有限公司 REVISION HISTORY ( )Preliminary Specification (√ )Final Specification Revision No. Preliminary Specification HongGuang Display Co.,Ltd

Open the catalog to page 2

General Description Absolute Maximum Ratings Electrical Specifications Optical Specifications Interface Connection Signal Timing Specification Input Signals, Display Colors & Gray Scale of Colors Power Sequence Connector Description Mechanical Characteristics Reliability Test Handling & Cautions Mechanical Outline Dimension EDID Table HongGuang Display Co.,Ltd

Open the catalog to page 3

深圳市鸿光显示有限公司 1.0 GENERAL DESCRIPTION 1.1 Introduction HG133FH017T01 is a color active matrix TFT LCD module using amorphous silicon TFT's (Thin FilmTransistors) as an active switching devices. This module has a 13.3 inch diagonally measured activearea with Full-HD resolutions (1920 horizontal by 1080 vertical pixel array). Each pixel is divided intoRED, GREEN, BLUE dots which are arranged in vertical stripe and this module can display 262k(6bit+FRC) colors and color gamut 72%. The TFT-LCD panel used for this module is a low reflection andhigher color type. Therefore, this module is suitable...

Open the catalog to page 4

1.3 Application • Notebook PC (Wide type) 1.4 General Specification The followings are general specifications at the model HG133FH017T01. (listed in Table 1) <Table 1. General Specifications> Notes : 1. LED Lighting Bar (36*LED Array) HongGuang Display Co.,Ltd HG133FH017T01 5 / 32

Open the catalog to page 5

2.0 ABSOLUTE MAXIMUM RATINGS The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and non-operational maximum voltage and current values are listed in Table 2. < Table 2. Absolute Maximum Ratings> Notes : 1. Permanent damage to the device may occur if maximum values are exceeded functional operation should be restricted to the condition described under normal operating conditions. 2. Temperature and relative humidity range are shown in the figure below. 95 % RH Max. ( 40 ° C > Ta) Maximum wet - bulb temperature at 39 ° C or...

Open the catalog to page 6

3.0 ELECTRICAL SPECIFICATIONS 3.1 Electrical Specifications < Table 3. Electrical Specifications > Ta=25+/-2°C 1. The supply voltage is measured and specified at the interface connector of LCM. The current draw and power consumption specified is for 3.3V at 25 °C. a) Typ : Mosaic pattern 8*8 btMax : R/G/B patterns EE 2. Calculated value for reference (Vled x Iled) 3. Measure condition (Figure 4) 4. Input voltage range:3.0~3.6V.Test condition: Oscilloscope bandwidth 20MHz, AC coupling.

Open the catalog to page 7

3.2 Backlight Unit < Table 4. LED Driving Guideline Specifications > Ta=25+/-2°C 1. Power supply voltage12V for LED driver. Calculator value for reference IF x VF x36 /driver efficiency = PLED 2. The LED life-time define as the estimated time to 50% degradation of initial luminous. 3. 1% duty cycle is achievable with a dimming frequency less than 1KHz. 4. Measure condition (Figure 5) Kiting time-W.ED UV ,rm r, VMHH Figure 5. Inrush Measure Condition

Open the catalog to page 8

HongGuang Display Co.,Ltd

Open the catalog to page 9

4.0 OPTICAL SPECIFICATION 4.1 Overview The test of optical specifications shall be measured in a dark room (ambient luminance < 1 lux and temperature = 25±2°C) with the equipment of luminance meter system (PR730&PR810) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of 9 and O equal to 0°. We refer to 90=0 (=93 ) as the 3 o’clock direction (the “right”), 90=90 (= 912 ) as the 12 o’clock direction (“upward”), 90=180 (= 99 ) as the 9 o’clock direction (“left”) and 90=27O(= 96 ) as the 6 o’clock direction (“bottom”). While scanning 9and/or...

Open the catalog to page 10

Notes : 1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing angles are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock direction with respect to the optical axis which is normal to the LCD surface (see Figure 7). 2. Contrast measurements shall be made at viewing angle of Θ= 0 and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state . (see Figure 7) Luminance Contrast Ratio (CR) is defined mathematically. CR = Luminance...

Open the catalog to page 11

深圳市鸿光显示有限公司 4.3 Optical Measurements TFT-LCD module Optical characteristics measurement setup Figure 7. Measurement Set Up Figure 8. White Luminance and Uniformity Measurement Locations (5 points) Center Luminance of white is defined as luminance values of center 5 points across the LCD surface. Luminance shall be measured with all pixels in the view field set first to white. This measurement shall be taken at the locations shown in Figure 7 for a total of the measurements per display. HongGuang Display Co.,Ltd

Open the catalog to page 12

Figure 9. Uniformity Measurement Locations (13 points) The White luminance uniformity on LCD surface is then expressed as : ΔY5 = Minimum Luminance of five points / Maximum Luminance of five points (see Figure 8) , ΔY13 = Minimum Luminance of 13 points /Maximum Luminance of 13 points (see Figure 9). Figure 10. Response Time Testing The electro-optical response time measurements shall be made as shown in Figure 10 by switching the “data” input signal ON and OFF. Tr: The luminance to change from 90% to 10% ,Tf: The luminance to change from 10% to 90% . The test system : PR810 HongGuang...

Open the catalog to page 13

Figure 11. Cross Talk Modulation Test Description Where: YA = Initial luminance of measured area (cd/m2) YB = Subsequent luminance of measured area (cd/m2) The location 1/2/3/4 measured will be exactly the same in both patterns. The test background gray is from L64 to L192.Take the largest data as the result. Cross Talk of one area of the LCD surface by another shall be measured by comparing the luminance (YA) of a 25mm diameter area, with all display pixels set to a gray level, to the luminance (YB) of that same area when any adjacent area is driven dark.(Refer to Figure 11) The test...

Open the catalog to page 14