
Shenzhen Hongguang Display Co.,Ltd CUSTOMER : CUSTOMER MODULE : Preliminary Specification ■Final Specification Customer Confirmation column: Approved by : Please return one of the copies of the specification with your signature to us within two weeks after you receive this document.If it is not returned,we will assume that you agree to the entire contents of this specification document. Hongguang Display
Open the catalog to page 1Hongguang Display
Open the catalog to page 2Shenzhen Hongguang Display Co.,Ltd Revision History Version Hongguang Display Preliminary Specification first update Modify BLU connector pin definition
Open the catalog to page 3Shenzhen Hongguang Display Co.,Ltd 1. GENERAL DESCRIPTION 1.1 General Description The specification is applied to 11.6inch model (HG116FH008 ) TFT Liquid Crystal Display. The matrix uses a-Si Thin Film Transistor as a switching device. This TFTLCD has a 11.6 inch diagonally measured active display area with FHD resolution (1920 horizontal by 1080 vertical pixels array). All input signals are eDP1.2 interface compatible. Hongguang Display
Open the catalog to page 4Shenzhen Hongguang Display Co.,Ltd 1.2 Features (1) 2 lane eDP interface with 2.7 Gbps link rates (2)16.7M color depth, color gamut 68% (3) Green product (RoHS & Halogen free product) (4) On board LED driving circuit (5) LED Dimming Mode DC 1.3 General Specifications The followings are general specifications. Table 1.General Specifications Item Active area Pixel pitch Pixel arrangement Display colors Color gamut Display mode Normally Black Outline Dimension Surface treatment Surface hardness Power consumption 2. ABSOLUTE MAXIMUM RATINGS 2.1 Absolute Maximum Ratings Hongguang Display
Open the catalog to page 5Shenzhen Hongguang Display Co.,Ltd The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and non-operational maximum voltage and current values are listed in Table 2. Table 2.Absolute Maximum Ratings Ta=25+/-5°C Parameter Logic Supply Voltage Logic Input Signal Voltage Operating Temperature Storage Temperature Note (1) All the parameters specified in the table are absolute maximum rating values that may cause faulty operation or unrecoverable damage, if exceeded. Note (2) All the contents of electro-optical specifications and display...
Open the catalog to page 6Shenzhen Hongguang Display Co.,Ltd Relative Humidity (%RH) Storage Range Temperature (ºC) Figure 3. Absolute Ratings of Environmentof the LCD Module (ºC) 3. ELECTRICAL SPECIFICATIONS 3.1 Interface Connector Table 3. Signal Connector Type Item Manufacturer / Type Table 4. Signal Connector Pin Assignment SIGNAL NAME DESCRIPTION Hongguang Display
Open the catalog to page 7Shenzhen Hongguang Display Co.,Ltd 12 Hot Plug Detect Output System PWM Signal Input 3.2 Signal Electrical Characteristics Table 5. Display Port Main Link Parameter Differential Common Mode Voltage Differential Peak to Peak Voltage Level 1 Note: (1) Input signals shall be low or Hi- resistance state when VCC is off. (2) It is recommended to refer the specifications of VESA Display Port Standard. Hongguang Display
Open the catalog to page 8Shenzhen Hongguang Display Co.,Ltd Figure 4. Display Port Main Link Signal Figure 5. Display Port AUX_CH Signal Table 6. Display Port AUX_CH Parameter VCM VDiff P-P Common Mode Voltage When receiving Common Mode Voltage When transmitting DifferentialPeak to Peak Voltage Note: Follow as VESA Display Port standard. Table 7. Display Port VHPD Parameter Note: Follow as VESA Display Port standard. 3.3 Interface Timings Table 8. Interface Timings Parameter Clock Frequency Frame Rate Note1: HT *VT *Frame Frequency≤165.3 MHz Note2: All reliabilities are specified for timing specification based on refresh...
Open the catalog to page 9Shenzhen Hongguang Display Co.,Ltd Allowable Logic/LCD Drive Ripple Voltage LED Power Supply LED Driver Input Voltage PWM Signal Voltage LED Enable Voltage VPWM VLED_EN Duty Ratio Note (1)All of the specifications are guaranteed under normal conditions. Normal conditions are defined as follow: Temperature: 25℃, Humidity: 50±10%RH. Note (2) All of the absolute maximum ratings specified in the table, if exceeded, may cause faulty operation or unrecoverable damage. It is recommended to follow the typical value. Note (3) The specified VCC current and power consumption are measured under the VCC=3.3V,...
Open the catalog to page 10Shenzhen Hongguang Display Co.,Ltd 3.5 Power ON/OFF Sequence Interface signals are also shown in the chart. Signalsfrom any system shall be Hi-Z state or low level when VCCvoltageis off. T11 eDP Display HPD From Sink Video from source Automatic or sink RFB Black Video Automatic Black Video Sink AUX CH Source Main Link Data link trainin idle g valid video data or PSR active Figure 5. Power Sequence Hongguang Display
Open the catalog to page 11Shenzhen Hongguang Display Co.,Ltd Table 10. Power Sequencing Requirements Parameter Delay from VCC to automatic Black Video generation Delay from VCC to HPD high Delay from HPD high to link training initialization Link training duration Link idle Delay from valid video data from Source to video on display Delay from valid video data from Source to backlight enable Delay from backlight disable to end of valid video date Delay from end of valid video data from Source to VCC off Delay from VLED to PWM Delay from VLED to backlight enable Delay from backlight disable to VLED off Delay from PWM off...
Open the catalog to page 12Shenzhen Hongguang Display Co.,Ltd 4.OPTI CAL SPECIFICATION 4.1 The table below is the test condition of optical measurement. Table 13. Test condition of optical measurement Item Ambient Temperature Ambient Humidity Supply Voltage Driving Signal Refer to the typical value in Chapter 3: ELECTRICAL SPECIFICATIONS Vertical Refresh Rate Dark room Hongguang Display
Open the catalog to page 13Shenzhen Hongguang Display Co.,Ltd 4.2 Optical Specifications Table 14. Optical Specifications Item Under C-light Blue White Contrast Ratio Response Time Unit Note Viewing Angle Notes: (1)The color chromaticity coordinates specified in Table 14 shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel. (2) Definition of Contrast Ratio (CR): The contrast ratio can be calculated by the following expression, Contrast Ratio (CR): CR = CRW : Luminance of LCD module with full screen white pattern (255,255,255)...
Open the catalog to page 1430 Pages
21 Pages
20 Pages
64 Pages
23 Pages
32 Pages
22 Pages
27 Pages
12 Pages
12 Pages
38 Pages
19 Pages
19 Pages
18 Pages
24 Pages
21 Pages
20 Pages
19 Pages
19 Pages
20 Pages
20 Pages
18 Pages
20 Pages
20 Pages
20 Pages
22 Pages
25 Pages
23 Pages
23 Pages
23 Pages
24 Pages
27 Pages
30 Pages
23 Pages
18 Pages
17 Pages
17 Pages
17 Pages
22 Pages
17 Pages
19 Pages
13 Pages
13 Pages
17 Pages
17 Pages
18 Pages
18 Pages
18 Pages
19 Pages
19 Pages
12 Pages
19 Pages
19 Pages
20 Pages
22 Pages
19 Pages
14 Pages
13 Pages
19 Pages
19 Pages
23 Pages
23 Pages
20 Pages
19 Pages
18 Pages
12 Pages
23 Pages
23 Pages
12 Pages
20 Pages
20 Pages
25 Pages
14 Pages
13 Pages
19 Pages
22 Pages
13 Pages
13 Pages
21 Pages
25 Pages
13 Pages
18 Pages
30 Pages
21 Pages
18 Pages
16 Pages
1 Page
16 Pages
20 Pages
16 Pages
20 Pages
39 Pages
50 Pages
50 Pages
49 Pages
7 Pages
20 Pages
30 Pages
17 Pages
21 Pages
30 Pages
30 Pages
17 Pages
19 Pages
15 Pages
17 Pages
19 Pages
14 Pages
22 Pages
19 Pages
16 Pages
16 Pages
18 Pages
10 Pages
17 Pages
19 Pages
20 Pages
17 Pages
17 Pages
21 Pages
21 Pages
19 Pages
14 Pages
16 Pages
20 Pages
18 Pages
19 Pages
19 Pages
19 Pages
18 Pages
18 Pages
29 Pages
18 Pages
12 Pages
21 Pages
18 Pages
18 Pages
20 Pages
19 Pages
10 Pages
10 Pages
10 Pages
20 Pages
19 Pages
19 Pages
20 Pages
20 Pages
20 Pages
13 Pages
13 Pages
26 Pages
13 Pages
22 Pages
24 Pages
19 Pages
13 Pages
13 Pages
13 Pages
13 Pages